Skip to content

ThunderFly JST-GH connector cables for Pixhawk based drones

License

Notifications You must be signed in to change notification settings

ThunderFly-aerospace/TFCAB01

Folders and files

NameName
Last commit message
Last commit date

Latest commit

 

History

17 Commits
 
 
 
 
 
 

Repository files navigation

TFCAB01 - ThunderFly Pixhawk compatible cabling system

TFCABxxyy01 are silicone cables for Pixhawk based drones. The cables are equipped on both sides with JST-GH high-strength plastic clips, which feature a locking mechanism for good mechanical connection and resistance to vibrations. Cables are designed and manufactured to have increased resistance to electromagnetic interference and self cross-talk.

Where I can buy them?

I sell on Tindie

Cables can be purchased online from Thunderfly Tindie store or contact ThunderFly team by email info@thunderfly.cz for individual quotation. Links to individual variants can be found in the following list.

List of ThunderFly cables

Currently, there are available cables mainly for I²C and UAVCAN busses, although more cable variants are defined. That less common variants of cables could be delivered upon request.

  • TFCAB15I2C01 (I2C, 15cm), buy it online
  • TFCAB30I2C01 (I2C, 30cm), buy it online
  • TFCAB45I2C01 (I2C, 45cm), buy it online
  • TFCAB15CAN01 (CAN, 15cm)
  • TFCAB30CAN01 (CAN, 30cm)
  • TFCAB45CAN01 (CAN, 45cm)

Wires

  • Insulation: Silicone, high temperature resistant (up to 200 °C)
  • Wire outer diameter: 1mm
  • Conductor: 26 AWG; 20/0.08, Sn plated Cu
  • Wire ending: JST-GH

Plastic endings

We use original JST-GH connectors from the manufacturer JST (JAPAN SOLDERLESS TERMINALS).

Color scheme

For easy orientation in avionics cabling cables we have designed a ThunderFly color scheme. The each type of signal/cable has own color combination, which is common in all our equipment.

I2C bus

Signal Pixhawk Color ThunderFly color
+5V Red red Red
SCL Black yellow Yellow
SDA Black green Green
GND Black black Black

ThunderFly I2C JST-GH connection cable

Cable twisting

  • 10 turns for each pair SCL/+5V and SDA/GND per 30cm cable length
  • 4 turns of both pairs together per 30cm cable length.

UAVCAN bus

Signal Pixhawk Color ThunderFly color
+5V Red red Red
CAN_H Black white White
CAN_L Black yellow Yellow
GND Black black Black

ThunderFly CAN JST-GH connection cable

Cable twisting

  • 10 turns for each pair GND/+5V and CAN_L/CAN_H per 30cm cable length
  • 4 turns of both pairs together per 30cm cable length.

UART/TELEM/SERIAL

UART is used to connect peripherals to the autopilot. By default, UART does not support networking and therefore it directly connects two devices together. It is often used to connect an autopilot and a radio modem. CTS and RTS are signals that are used to indicate that data is being transmitted on TX/RX pins. This hand-shake mechanism increases reliability of data transfer. CTS and RTS may remain loose when it is not used by the device. The connecting cable is not crossed. Therefore, it is necessary to connect only the autopilot and peripherals with this straight cable. The device must cross the wiring internally by swapping RX/TX and RTS/CTS pins.

Signal Pixhawk Color ThunderFly color
+5V Red red Red
TX Black white White
RX Black green Green
CTS Black blue Blue
RTS Black yellow Yellow
GND Black black Black

UART signals are common sources of low frequency EMI, therefore the length of the cable should be minimized as much as possible. Cable twisting is not applicable for UART cables due to possible increase of cross-talks.