Skip to content

nostradomus/ATtinyISPprogrammerShield

Folders and files

NameName
Last commit message
Last commit date

Latest commit

 

History

86 Commits
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Repository files navigation

ATtiny ISP programmer shield for Arduino UNO boards

What

This repo provides you with all necessary info (and files) to build an Arduino shield to program Atmel's attiny 𝜇-controllers. For that matter, the underlying Arduino board should be loaded with the ISP-programmer sketch (built-in example).

Shield - topview Shield - bottomview

Why

Often, one of these "tiny" chips is largely powerful enough for the design of small projects. During the design phase, I however got tired of wiring up things on a breadboard. As (like many people) I was having a spare UNO, which could serve as an ISP programmer, I decided to design a minimalistic shield to fit on top of it.

PCB - component side PCB - copper side

How

The shield has been designed with EAGLE from AutoDesk/CadSoft. This shield project can be opened with the free version (download here). In order to keep things simple, the V1 PCB can be etched single-sided, as the top-layer only contains a couple of short connections (which can easily be replaced by wire-bridges). The V2 PCB (a real double-sided version) has optimised routing and ground-pours. Only through-hole components have been used in order to make the built also feasible for any beginner. In the pdf-folder of this repo pdf versions of all important EAGLE views are available, for those not wanting to install EAGLE. Pay attention to print the bottom and top-layer layouts without re-sizing (1:1). To have the printed circuit board built by a commercial PCB-shop, the gerber-files are also available.

Currently, unpopulated V2 boards are still available from our workshop. If interested, contact us via 📧.

PCB PCB

Technical details

What’s on the board

The board is fit with 3 IC sockets (8, 14 and 20 pin), for the 3 types attiny’s. Only one chip should be fit at a time ❗ On the prototype, pin headers with double functionality have been mounted. Pins on the bottom-side to fit on the Arduino board, and feed-through female headers on the top for easy access of all Arduino connections. The push button, is connected to the reset lines of the attiny’s with a 10kΩ pull-up resistor. When the shield is cut correctly, the reset button for the Arduino UNO itself should still be accessible. In order to make the Arduino Uno work as an ISP programmer a 10µF capacitor needs to be connected on its reset-line. Three LED’s are available to visualise the correct functionality of the programming procedure. An optional AVR ISP socket has been foreseen in order to use the shield as stand-alone with a commercial programmer.

V2 shield with text annotations V1 shield with text annotations

BOM - bill of materials

Part Value Package Description
R1 10kΩ 0207/7 resistor
R2,3,4 270Ω 0207/7 resistor
C1 10µF/16V E2,5-6E polarized capacitor
C2,3,4 100nF C050-025X075 capacitor
LED1 3mm yellow 3mm LED
LED2 3mm red 3mm LED
LED3 3mm green 3mm LED
IC1 8-pin DIL08 IC socket
IC2 14-pin DIL14 IC socket
IC3 20-pin DIL20 IC socket
ICSP1 2x3 pin-header 2x3 AVR ISP-6 Serial Programming Header (optional)
S1 momentary 6x6x6mm momentary tact push button
S2 SPDT MINI SWITCH 90 mini toggle switch
CON1 6-pin SIL06 long needle female stackable pin header strip
CON2,3 8-pin SIL08 long needle female stackable pin header strip
CON4 10-pin SIL10 long needle female stackable pin header strip

How things work

First the the ISP-programmer sketch (built-in example) should be loaded to the Arduino UNO board. During that operation, switch S2 should be set to 'PROG' (or remove the blue jumper JP1 on a V1 board). Select “Arduino Uno” as target board in the tools-menu. Load the ISP-programmer sketch with the “UPLOAD” button. Once loaded, the jumper can be put back to send your a sketch to your attiny 𝜇-controller.

ISP example sketch Board selection Upload

To load a sketch to your attiny chip, make sure that the correct target board is selected in the tools-menu (you might need to download a specific library -> tools-menu, board manager). This time, use the “UPLOAD USING PROGRAMMER” option from the sketch-menu.

Programmer selection Upload Using Programmer

The 3 LED’s will tell you how things are going :

  • Green : ISP programmer running
  • Yellow : uploading sketch
  • Red : error

Proof of concept

So far, I have tested the shield with the below list of 𝜇-controllers :

  • attiny84
  • attiny85
  • attiny2313
  • attiny4313

Any pin-compatible 𝜇-controller should work as well :

  • 8-pin : attiny10/11/12/13/15/22/25/45/85
  • 14-pin : attiny24/44/84
  • 20-pin : attiny2313/4313 (on condition of using the correct settings in your Arduino programming environment)

Contributors

If you are having any good suggestions, just drop me a line 📧. If feasible, I'll be happy to implement any proposed improvements. And if you are having lots of time, I'll be happy to share the work with you ;-).

🌐 License

At this moment, there is no specific license attached to this project.

So, today, if you like it, have fun with it (at your own risk of course :-D), and especially, be creative.

Oh, and when using anything from this repository, it is highly appreciated if you mention its origin.

If you would like to use any of this work (or the whole project) for commercial use, first contact us 📧, so we can add the appropriate license, which best fits your business.