iiwa_setup

iiwa real-world setup

Installation

This repo uses Poetry for dependency management. To set up this project, first install Poetry and, make sure to have Python3.10 installed on your system.

Then, configure poetry to set up a virtual environment that uses Python 3.10:

poetry env use python3.10

Next, install all the required dependencies to the virtual environment with the following command:

poetry install -vvv

(the -vvv flag adds verbose output).

For local Drake and manipulation installations, insert the following at the end of the .venv/bin/activate and .venv/bin/activate.nu files, modifying the paths and python version as required:

export PYTHONPATH=""
export PYTHONPATH=~/drake-build/install/lib/python3.10/site-packages:${PYTHONPATH}
export PYTHONPATH=~/manipulation:${PYTHONPATH}

Activate the environment:

poetry shell

Install git-lfs:

git-lfs install
git-lfs pull

iiwa Driver

Drake's iiwa driver must be installed manually to use the real iiwa robot. NOTE that Drake's pre-requisites must be installed before installing the driver.

The FRI source can be downloaded from here and installed using the following instructions (from the driver repo):

cd kuka-fri
unzip /path/to/your/copy/of/FRI-Client-SDK_Cpp-1_7.zip
patch -p1 < ../fri_udp_connection_file_descriptor.diff

Once build, the driver can be run using ./bazel-bin/kuka-driver/kuka_driver or using bazel run //kuka-driver:kuka_driver.

Networking troubleshooting

If the driver doesn't connect to the kuka, check that the sunrise cabinet is reachable on the network using nmap -sP 192.170.10.2/24. Both the local computer and a second computer (the sunrise cabinet) should show up.

If it doesn't show up, check the following:

1. There must be an ethernet network connecting the local computer and the sunrise sunrise cabinet KONI port (ideally through a switch). This network must have the static IP 192.170.10.200 with netmask 255.255.255.0.
2. The sunrise cabinet KONI port must be owned by RTOS and not by Windows. Connect a monitor, mouse, and keyboard to the sunrise cabinet. Start the cabinet and login. Press WIN+R to open the command window. Type C:\KUKA\Hardware\Manager\KUKAHardwareManager.exe -query OptionNIC -os RTOS. Everything is in order if the popup says BusType OptionNIC found. If the popup says BusTypeOptionNIC not present, change the port ownership using C:\KUKA\Hardware\Manager\KUKAHardwareManager.exe -assign OptionNIC -os RTOS. Unplug the monitor and restart the sunrise cabinet before re-checking the network with nmap.

Port troubleshooting

Make sure that the sunrise cabinet port matches the kuka driver port. If not, then modify the kuka driver source code to change the port (kuka-driver/kuka_driver.cc/kDefaultPort). It is also possible to start the kuka driver with a specific port over the command line. However, it is easier to hardcode the port as the cabinet port won't change.

Robot limit exceeded errors

1. Enter the KRF mode
2. Manually operate the robot out of the limits using the tablet
3. Re-enter automatic mode

If no KRF mode exists, then do the following:

1. Unmaster the joint whose limits are exceeded
2. Use the teach pendant in T1 mode to move the joint back inside its allowed range
3. Master the joint

"Voltage of intermediate circuit too low" error

One of the fuses is blown. You need to open the control box and replace them.

The two fuses are:

• 5A/80V Automotive Fuse (buying link)
• 7.5A/80V Automotive Fuse (buying link)

Schunk WSG 50 Gripper Driver (Optional)

Connect the WSG gripper to the same switch that is connecting the local computer with the sunrise cabinet. Add the IP 192.168.1.200 with netmask 255.255.255.0 as an additional static IP to the network (the first IP should still be 192.170.10.200). The WSG is connected properly if the WSG 50 Control Panel web interface can be accessed through http://192.168.1.20/. Try to control the gripper through the web interface. If this doesn't work, then controlling it through the driver also won't work.

Drake's Schunk driver must be installed manually to use the WSG programatically. Once built, the driver can be run using bazel run //src:schunk_driver. The driver requires Bazel 6. Multiple Bazel versions can be managed by installing bazelisk from [here](https://github.com/bazelbuild/bazelisk/releases). The Bazel version will then be read from the .bazeliskrc` file in the repo.

Networking troubeshooting

Check that one host shows up when using nmap -sP 192.168.1.201. and that the website is accessible at http://192.168.1.20/. If not, then check that you followed the IP instructions and that the gripper's ethernet cable is plugged into the switch.

Error while moving: The device is not initialized

1. Navigate to the website http://192.168.1.20/
2. Motion -> Manual Control
3. Click on Home and wait until the homing sequence is finished
4. Re-try commanding the gripper via the web interface

Getting system info failed

Follow the wsg driver setup instructions. In particular, the gripper might be set to ICP instead of UDP.

Optitrack Driver (Optional)

Drake's Optitrack driver must be installed manually to use the Optitrack functionality.

Build and install the wheel as described here. Make sure to install the wheel from inside the poetry virtual environment.

FT 300-S Driver (Optional)

The FT 300-S LCM driver must be installed according to its README instructions.

The included LCM messages must be added to the python path (after building):

export PYTHONPATH=~/path_to_parent_dir/ft_300s_driver/bazel-bin/lcmtypes/ft_300s/:${PYTHONPATH}

Executing code on the real robot

1. Start the DrakeFRIPositionDriver or DrakeDRITorqueDriver on the teach pendant.
2. Run the iiwa driver by running bazel run //kuka-driver:kuka_driver from drake-iiwa-driver.
3. If using the WSG, run the schunk driver using bazel run //src:schunk_driver from drake-schunk-driver.
4. Run the desired script with the --use_hardware flag.

Note about timesteps

The torque_only driver runs at 1000Hz while all other controllers run at 200Hz. The specified timesteps should match the controllers, i.e. 0.001 for the torque_only driver and 0.005 for all other drivers.

Controlling the robot in torque_only mode

NOTE: It is recommended to calibrate the joint torque sensors before running the robot in torque_only mode. This can be achieved by running the PositionAndGMSReferencing application on the teach pendant.

1. Start the DrakeFRITorqueOnlyDriver on the teach pendant.
2. Optional: Make sure that the iiwa driver is build by running bazel build //... from drake-iiwa-driver.
3. Run the iiwa driver by running sudo ./bazel-bin/kuka-driver/kuka_driver --torque_only=true --time_step 0.001 --realtime from drake-iiwa-driver (sudo is required for --realtime which helps but is not required).
4. Run the desired script with the --use_hardware flag.

Obtaining slightly better performance

You might be able to achieve slightly better performance in torque_only mode by pinning the processes to the same core and increasing their priority.

1. Make sure that you can run chrt without sudo privileges: sudo setcap cap_sys_nice=eip /usr/bin/chrt. This is only required once.
2. Run the desired script using taskset -c 1,29 chrt -r 90 python {...} --use_hardware.

Optitrack

To use the Optitrack system, run the Optitrack client from the driver directory:

bazel run //src:optitrack_client

Inspecting Optitrack LCM messages

Clone drake and run LCM Spy from inside the drake directory:

bazel run lcmtypes:drake-lcm-spy

Calibrating Optitrack bodies

In a usual setup, we want to use Optitrack to update our internal model of the world (multibody plant). However, the body poses returned by Optitrack assume different world and body frames than the ones from our plant. Hence, we need to find the transform between the Optitrack body pose and the plant body pose.

scripts/calibrate_optitrack_body.py can be used for computing this transform using the the following procedure:

1. Setup

Make sure that the optitrack iiwa frame is in the middle of the iiwa (in the middle of the 4 corner points of which 3 are optitrack markers). By default, the frame will be in the middle of the 3 optitrack markers, which is slightly different. It can be changed using the optitrack GUI.

Modify the scenario_str to contain the body of interest (currently sugar_box.dmd.yaml) and a second (reference) version of that body (currently sugar_box_reference.dmd.yaml). Both should be identical apart from the model name and contain the SDFormat file of the body/ object.

Modify object_name and ref_object_name to match the model names of the first and second version of the body.

Modify ref_object_initial_positions to position the body above the Optitrack workspace (the object should fall on the floor and not start on the floor).

Modify optitrack_iiwa_id and optitrack_body_id to match the body IDs of the Optitrack system. These can be identified as described here.

Make sure that X_oB_pB = RigidTransform([0, 0, 0]) is uncommented.

2. Determine the reference body's positions

1. Set is_init = True and run the script.
2. Wait a few seconds until the printed pose stays approximately static. Then note down the printed z-position and terminate the script.
3. Modify the reference body directive file to include a weld from the world frame to the body frame. The weld transform should include the printed z-position, no rotation, and planar positions that position the object close to the iiwa base inside the Optitrack workspace.

3. Determine the Optitrack body to plant-body transform

1. Place the real object at the planar position that corresponds to the weld from step 2. Taking the iiwa center as the world origin and using a ruler to measure positions and ensuring axis-aligned rotations should be helpful strategies here.
2. Remove the collision geometries from the body SDFormat file.
3. Set is_init = False and run the script.
4. Note down the printed transform and terminate the script.
5. Set X_W_oB to the printed transform.
6. Comment out X_oB_pB = RigidTransform([0, 0, 0]).
7. Run the script and check if both bodies align. If they do, then X_oB_pB represents the desired transform.

Recording Optitrack object pose data

The script scripts/record_optitrack_body_pose_data.py can be used for recording the pose of an object using optitrack.

Example usage:

python scripts/record_optitrack_body_pose_data.py --out_path sugar_box_logs \
--object_directive "package://iiwa_setup/sugar_box.dmd.yaml" --object_name sugar_box \
--optitrack_object_id 3 --object_initial_positions '[1, 0, 0, 0, 0.5, 0.5, 0.025]' \
--p_optitrackBody_plantBody_world '[-0.03427348, 0.01983565, -0.01967432]' \
--R_optitrackBody_plantBody_world '[0.013, -0.035, 1.372]' --save_html

Note that data is only saved if the script is excited gracefully using the Stop Simulation button in Meshcat.

Simulating Optitrack Measurements

The script scripts/simulate_optitrack.py can be used to simulate Optitrack frame measurements. The script either loads Optitrack frames and their associated publish times from disk (arbitrary number of objects) or opens a GUI for interactively moving a single object.

Example usage (disk):

python scripts/simulate_optitrack.py --optitrack_frames_path frames.npy \
--optitrack_frame_times_path frame_times.npy

Example usage (GUI):

python scripts/simulate_optitrack.py --initial_object_position '[0.5, 0.0, 0.15]' \
--initial_object_quaternion '[1.0, 0.0, 0.0, 0.0]' --optitrack_object_ids '[4, 3]'