GAME BOY Pokemon Trading MALVEKE

FW Official	FW Unleashed	FW RogueMaster	FW Xtreme

Introduction

This is a Pokemon exchange application from Flipper Zero to Game Boy (Generaction I). Flipper Zero emulates a "Slave" Game Boy connected to a Game Link Cable to be able to exchange any Pokemon from the First Generation (Red, Blue, Yellow) to a real Game Boy.

It currently trades a Pokemon based on your choice of Pokemon, Level, Stats and 4 Moves.

Hardware Interface

The Game Boy is connected to the Flipper Zero's GPIO pins via a GBC style Game Link Cable. The Flipper GB Link module is an easy way to connect a Game Boy via a Game Link Cable to the Flipper Zero.

Additionally, the MALVEKE - GAME BOY Tools for Flipper Zero is supported by this tool.

Details on the hardware interface, as well as how to create your own adapter board, can be found in the How Does It Work section below.

Installation Directions

This project is intended to be overlaid on top of an existing firmware repo, in my case the Release 0.79.1 version.

• Clone the Flipper Zero firmware repository. Refer to this tutorial for updating the firmware.
• Copy the "pokemon" folder into the /applications_user/pokemon folder in your firmware.
• Run the command fbt launch to run it on your Flipper Zero.

./fbt launch APPSRC=pokemon

• NOTE: If you only want to generate the fap file, you must run the following command.

./fbt fap_pokemon

And use qFlipper to copy the generated pokemon.fap file to the SD Card/apps/Game Boy folder.

Instructions for use.

These instructions assume that you are starting at the Flipper Zero desktop. Otherwise, press the Back button until you are at the desktop.

• If you're using a MALVEKE PCB version, verify the Pinout configuration:

  
  
  

  • MALVEKE 2.5 PCB Version: If you're using this version, select the MALVEKE configuration.

    
    
    

  • MALVEKE 2.5.1 PCB Version: If you're using this version, select the ORIGINAL

    
    
    

• Press the OK button on the Flipper to open the main menu.

• Choose Applications from the menu.

• Choose GPIO from the submenu.

• Choose Pokemon Trading

• The Flipper Zero will show the main menu of the application. The first option is to select the Pokemon to trade.

  
  
  

• Press the LEFT/RIGHT buttons to paginate the selection of Pokemon by 1.

• Press the UP/DOWN buttons to paginate the selection of Pokemon by 10.

• Press the OK button to select the Pokemon to trade and return to the main menu

  
  
  

• The traded Pokemon's nickname can be set. When a Pokemon is selected, the nickname defaults to the species name in all caps. This mimics a Pokemon without a customized nickname. In order to reset this nickname to its default, clear the text entry field, press OK on the Save button. This will fill the text box with the default name. Press Save again to set this name.

  • Note: The Nidoran♀ and Nidoran♂ names will not properly render. This is because the Flipper currently cannot print unicode characters to screen. Following the above instructions will fill the text entry field with NIDORAN with a space after it. This space is the unrenderable ♀/♂ symbol. Once traded, it will be correctly named.

  • Note: Only alphanumeric characters are supported in the Pokemon's nickname at this time.

    
    
    

• The Pokemon's level can be adjusted as well by hitting OK on the level option. The minimum level is 2 and the maximum is 100. The level is input via a text box. (Levels below 2 cause an underflow glitch in Gen I games that would cause the level to jump to 100, so if you want this just set the Pokemon's level to 100)

  
  
  

• The Select Moves menu is used to pick the set the traded Pokemon's moves. They are pre-populated with the moveset that the Pokemon would know at level 1. Selecting a move slot will bring up an alphabetical index of moves. Additionally, No Move and Default can be quickly selected. Note that any move after the first No Move is ignored.

  
  
  

  
  
  

• The Select Types menu can change the traded Pokemon's types. The type(s) are pre-set to what the selected Pokemon normally is.

  • Pokemon with a single type will have the same type set for both types.

  • Note: Unlike other menus, changing either type immediately saves it. Pressing Back will keep any changes. This will be addressed in a later version. If you need to revert to the default types, a different Pokemon can be selected and the desired Pokemon re-selected.

  • Note: When changing the type(s), the Pokemon's in-game stats will NOT reflect the chosen type(s). Additionally, these may be overwritten back to default in-game if the Pokemon uses a move that affects types (e.g. Transform) or the Pokemon evolves.

    
    
    

• The Pokemon's stats can also be influenced. The current settings are:

  • Random IV, Zero EV Mimics stats of a caught wild Pokemon.

  • Random IV, Max EV / Level IV is randomized, but EV is set to the maximum a trained Pokemon could be for its current level.

  • Random IV, Max EV IV is randomized, EV is set to the absolute max for a perfectly trained Pokemon.

  • Max IV, Zero EV Mimics stats of a caught wild Pokemon, but with the maximum IV possible.

  • Max IV, Max EV / Level IV is max, EV is set to the maximum a trained Pokemon could be for its current level.

  • Max IV, Max EV Absolutely perfect and overly powerful Pokemon.

    
    
    

• The OT ID# and OT Name of the Pokemon can also be set. The OT ID# must be between 0 and 65535. Setting the OT ID# and OT Name to the same as your current trainer's causes the game to believe it was a wild caught Pokemon and not one that was traded. This means high level Pokemon will still obey you without badges, but, will not get the experience boost of a traded Pokemon.

  
  
  

  
  
  

• Finally, select Trade PKMN to start the trade process.

  
  
  

  
  
  

• On your Game Boy, you should connect the Game Link Cable to the Game Boy and in the game, go to the nearest Pokemon Center.

  
  
  

• Talk to the girl at the counter on the right. The girl will tell us that we have to save the game before playing, we will answer YES by pressing the A button.

  
  
  

• The Flipper Zero will show that we are connected.

  
  
  

• On the Game Boy, we will be asked which option we want, and we select TRADE CENTER.

  
  
  

• You will enter the Trade Center where you must press the A button on the Game Boy on your side of the table.

  
  
  

• Flipper Zero will remain on a waiting screen with the Pokemon you selected.

  
  
  

• You will see your Pokemon and the Pokemon you selected on the Flipper Zero, in this case, Mew. You must select the Pokemon you want to trade and press TRADE.

  
  
  

• You must confirm the selected trade by selecting TRADE.

  
  
  

• Flipper Zero will remain on a waiting screen with the Pokemon you selected.

  
  
  

• Finally, the Pokemon exchange will start from Flipper Zero to the Game Boy.

  
  
  

• Once the trade is complete, both the Game Boy and the Flipper Zero will return to the WAITING state. If the Game Boy selects CANCEL, the Flipper Zero will return to the READY state. The BACK button can be pressed to return to the main menu. The traded Pokemon can be modified, or completely changed, if desired. Once the Flipper Zero Re-enters the Trade screen, and the Game Boy re-selects the trade table in-game, another trade can be completed. This allows for trading multiple Pokemon without having to reset the Game Boy each time.

  If the Flipper Zero gets stuck at the end of the exchange, you must reboot it by pressing the LEFT + BACK key combination.

  
  
  

How does it work?

The method used to communicate 2 Game Boys is based on the SPI protocol, which is a very simple serial communication protocol in which a master device communicates with one or more slave devices. The protocol is bidirectional and synchronous, and uses three basic signals:

• A clock signal (CLK).
• An output signal (Serial Out or SO).
• An input signal (Serial In or SI).

In the Game Boy, games store data in an internal shift register that is used to send and receive information. The SPI protocol used by the Game Boy uses the clock signal to indicate when data is being transferred.

The Game Boy link protocol is synchronous and requires the slave device to respond at the same rate as the master device. The master device supplies an 8KHz clock (data transfer rate of 1KB/s). The time window for responding is only ~120μs. However, the slave device has no restrictions and can respond when it receives data. The clock can vary and there is no lower limit.

An example GB SPI transfer. Here, the master sends 0xD9 (217) and the slave sends 0x45 (69).

You can learn more about it in the following video. Analyzing the Different Versions of the Link Cable.

Board for Flipper Zero with PortData EXT Link.

For the Flipper Zero board, a PortData EXT Link and a 2x8 prototype board were used.

PortData EXT Link for Game Boy Color, Game Boy Pocket, GBC, GBP, GBL.

I used 33kΩ resistor on CLK, but it's optional, it can be connected directly.

Connection: Flipper Zero GPIO - Game Boy

The pins should be connected as follows:

Cable Game Link (Socket)	Flipper Zero GPIO
6 (GND)	8 (GND)
5 (CLK)	6 (B2)
3 (SI)	7 (C3)
2 (SO)	5 (B3)

Connect to Flipper Zero without Socket PortData EXT Link

It's possible to cut a cable directly without using a socket, but it's important to note that the cable is a crossover cable SI-SO.

"Cable Game Link" cut and directly connected to the Flipper Zero pins.

NOTE: Don't rely on the cable colors as they may vary depending on the manufacturer. Use a multimeter to measure continuity and identify which cable corresponds to each pin.

GUI

To generate the graphical interface, the FUI-Editor tool was used. Additionally, the original sprites from the game Pokemon Yellow, which are found in the Disassembly of Pokemon Yellow repository, were used.

For each image, the color #aaa was transformed to #fff so that Flipper Zero would render it correctly. To do this, a batch process was used in Photopea, the online image editor.

Tested In

• Game Boy Color (GBC)
• Game Boy Advance (GBA)

Contributors

Links

• Flipper Zero firmware source code
• Adan Scotney's Pokemon trade protocol specification and implementation
• Derek Jamison - Youtube Channel
• Matt Penny - GBPlay Blog
• Pokémon data structure (Generation I)
• Disassembly of Pokemon Yellow
• Arduino-Spoofing-Gameboy-Pokemon-Trades
• 🎮 Gameboy link cable breakout PCB

From Talcahuano 🇨🇱 with ❤