Skip to content
This repository has been archived by the owner on Aug 10, 2022. It is now read-only.

ESPHome component for the Bosch BME680 sensor via BSEC providing temperature, humidity, pressure and indoor air quality measurements.

Notifications You must be signed in to change notification settings

trvrnrth/esphome-bsec-bme680

Folders and files

NameName
Last commit message
Last commit date

Latest commit

 

History

42 Commits
 
 
 
 
 
 
 
 

Repository files navigation

🎁 Component now included in the core distribution 🎁

⚠️ Warning: You should only use this repository if you are specifically testing a new release or experimental feature.

Introduction

This component facilitates use of the Bosch BME680 sensor with ESPHome via the closed source Bosch BSEC library providing additional calculated indoor air quality measurements not available with the core component:

Home Assistant Entities

Installation

As of ESPHome 1.18 this component is included in the core distribution, however you may still wish to use this repository if a new release or experimental feature is available.

⚠️ Note: The Bosch BSEC library is only available for use after accepting its software license agreement. By enabling this component, you are explicitly agreeing to the terms of the BSEC license agreement.

As an external component

In ESPHome 1.18 and later you can use the external components system:

external_components:
  - source: github://trvrnrth/esphome-bsec-bme680

ESPHome 1.17 and earlier

Copy the components/bme680_bsec directory into your ESPHome custom_components directory (creating it if it does not exist). If you are running via Home Assistant this will be /config/esphome/custom_components/bme680_bsec.

Dependencies

The I2C Bus must be set up in order for this component to work.

Minimal configuration

The following configuration shows the minimal set up to read temperature and humidity from the sensor.

i2c:

bme680_bsec:

sensor:
  - platform: bme680_bsec
    temperature:
      name: "BME680 Temperature"
    humidity:
      name: "BME680 Humidity"

Advanced configuration

The following configuration shows all the available sensors and optional settings for the component. It also includes an example of filtering to guard against outliers, limit the number of updates sent to home assistant and reduce storage requirements in other systems such as influxdb used to store historical data.

For each sensor all other options from Sensor and TextSensor are also available for filtering, automation and so on.

bme680_bsec:
    # i2c address
    # -----------
    # Common values are:
    # - 0x76
    # - 0x77
    # Default: 0x76
    address: 0x76

    # Temperature offset
    # ------------------
    # Useful if device is in enclosure and reads too high
    # Default: 0
    temperature_offset: 0

    # IAQ calculation mode
    # --------------------
    # Available options:
    # - static (for fixed position devices)
    # - mobile (for on person or other moveable devices)
    # Default: static
    iaq_mode: static

    # Sample rate
    # -----------
    # This controls the sampling rate for gas-dependant sensors and will govern the interval
    # at which the sensor heater is operated.
    # By default this rate will also be used for temperature, pressure and humidity sensors
    # but these can be overridden on a per-sensor level if required.
    #
    # Available options:
    # - lp (low power - samples every 3 seconds)
    # - ulp (ultra low power - samples every 5 minutes)
    # Default: lp
    sample_rate: ulp

    # Interval at which to save BSEC state
    # ------------------------------------
    # Default: 6h
    state_save_interval: 6h

sensor:
  - platform: bme680_bsec
    temperature:
      # Temperature in °C
      name: "BME680 Temperature"
      sample_rate: lp
      filters:
        - median
    pressure:
      # Pressure in hPa
      name: "BME680 Pressure"
      sample_rate: lp
      filters:
        - median
    humidity:
      # Relative humidity %
      name: "BME680 Humidity"
      sample_rate: lp
      filters:
        - median
    gas_resistance:
      # Gas resistance in Ω
      name: "BME680 Gas Resistance"
      filters:
        - median
    iaq:
      # Indoor air quality value
      name: "BME680 IAQ"
      filters:
        - median
    iaq_accuracy:
      # IAQ accuracy as a numeric value of 0, 1, 2, 3
      name: "BME680 Numeric IAQ Accuracy"
    co2_equivalent:
      # CO2 equivalent estimate in ppm
      name: "BME680 CO2 Equivalent"
      filters:
        - median
    breath_voc_equivalent:
      # Volatile organic compounds equivalent estimate in ppm
      name: "BME680 Breath VOC Equivalent"
      filters:
        - median

text_sensor:
  - platform: bme680_bsec
    iaq_accuracy:
      # IAQ accuracy as a text value of Stabilizing, Uncertain, Calibrating, Calibrated
      name: "BME680 IAQ Accuracy"

Indoor Air Quality (IAQ) Measurement

Indoor Air Quality measurements are expressed in the IAQ index scale with 25IAQ corresponding to typical good air and 250IAQ indicating typical polluted air after calibration.

IAQ Accuracy and Calibration

The BSEC algorithm automatically gathers data in order to calibrate the IAQ measurements. The IAQ Accuracy sensor will give one of the following values:

  • Stabilizing: The device has just started, and the sensor is stabilizing (this typically lasts 5 minutes)
  • Uncertain: The background history of BSEC is uncertain. This typically means the gas sensor data was too stable for BSEC to clearly define its reference.
  • Calibrating: BSEC found new calibration data and is currently calibrating.
  • Calibrated: BSEC calibrated successfully.

Every state_save_interval, or as soon thereafter as full calibration is reached, the current algorithm state is saved to flash so that the process does not have to start from zero on device restart.

About

ESPHome component for the Bosch BME680 sensor via BSEC providing temperature, humidity, pressure and indoor air quality measurements.

Topics

Resources

Stars

Watchers

Forks