wgfrontend

A simple web frontend for configuring peers within a WireGuard configuration file to thus administer road warrior clients.

There are already a lot of user interfaces for administering WireGuard configuration files available. However, many of them have a bunch of dependencies, require root privileges to operate, or are a hassle to set up. "wgfrontend" provides a user interface that can be easily installed by just installing a package from Python's package repository PyPi (i.e. using pip).

This little tool is independent of the Towalink site connectivity solution (see https://towalink.readthedocs.io).

---

Features

• Web frontend for adding, modifying, and deleting WireGuard peers
• Config files for WireGuard peers can be downloaded
• Config files for WireGuard peers are shown as QR Code
• Assistant for initial set-up
• Web frontend has responsive design
• Web frontend does not run with root privileges
• Simple installation

---

Installation

Install using PyPi:

pip3 install wgfrontend

Note: In the case you get an error regarding the imaging library needed for generating QR Codes, try to install it via the operating system packages:

# For Alpine:
apk add py3-pillow
# For Debian:
apt install python3-pil

---

Quickstart

After installing "wgfrontend" as shown above, just execute the tool with root permissions to get started:

wgfrontend

An interactive set-up assistant queries for the needed configuration data and sets up the environment. Once everything is configured, "wgfrontend" drops root privileges and runs a small web server on port 8080 to serve the web frontend.

---

Screenshots

See additional screenshots in the "screenshots" folder.

---

Details

The wgfrontend configuration file

The interactive set-up assistant creates a configuration file with the desired information. It is located at "/etc/wgfrontend/wgfrontend.conf".

Here is an example:

### Config file of the Towalink WireGuard Frontend ###
[general]
# The WireGuard config file to read and write
wg_configfile = /etc/wireguard/wg_rw.conf

# The command to be executed when the WireGuard config has changed
on_change_command = "sudo /etc/init.d/wgfrontend_interface restart"

# The interface to bind to for the web server
socket_host = 0.0.0.0

# The port to bind to for the web server
socket_port = 8080

# The system user to be used for the frontend
user = wgfrontend

[users]
admin = dc524e423d9762830649d4d9e18f4b47a56c92f96646104dd06c71b26b54f732e8318d5b60a6b2b01b4f269407771496e879c9bf65ca9ef4f55a243ff358fc8dfea0bd9d30d766320857093eb95022822f71b098215f26f6d2644033d956bfdd

Add an additional frontend user

Create a password hash using the following command:

wgfrontend-password

Using this, you can add another user to the [users] section in the wgfrontend configuration file.

A note on security

Don't expose the web frontend to the Internet without another layer of protection.

The wgfrontend web server does not run with root permissions. That's a start and better than many other WireGuard frontends. But the web server user has the permission to write to a WireGuard configuration file. This file may reference scripts that are run with root permissions when wg-quick is run. In case of a vulnerability in wgfrontend, this can be abused for privilege escalation. Thus add an additional safeguard layer of protection.

---

Reporting bugs

In case you encounter any bugs, please report the expected behavior and the actual behavior so that the issue can be reproduced and fixed.

---

Developers

Clone repository

Clone this repo to your local machine using https://github.com/towalink/wgfrontend.git

Install the module temporarily to make it available in your Python installation:

pip3 install -e <path to directory with setup.py>

---

License

• AGPL3 license
• Copyright 2020 © Dirk Henrici.
• WireGuard is a registered trademark of Jason A. Donenfeld.