Skip to content

maxvfischer/DIY-CNC-machine

Repository files navigation

main_gif

This guide goes through all the steps to build your own CNC machine from scratch. It includes a complete bill of materials (BOM), STL/OBJ-files for all the 3d-printed parts and detailed instructions of how everything is assembled. It also includes instructions of how all the necessary open-source softwares are installed.

The guide is based on Ivan Miranada's design and is a complement to Ivan's Youtube-videos:

  1. Original video: https://www.youtube.com/watch?v=_atw3e0nIrg
  2. Updates with geared stepper motors etc: https://www.youtube.com/watch?v=qpjf5D3WngY
  3. Updating to metal parts: https://www.youtube.com/watch?v=RDnGvhdGFEY

If you have any questions, feel free to contact me on LinkedIn: https://www.linkedin.com/in/max-fischer-92997281/

or

contact

cnc_top_gif


Featured on


Table of content

  1. License
  2. Parts (bill of materials)
  3. Build the CNC machine
    1. Main frame
      1. Drill holes in 900 mm profiles
      2. Rails to 900 mm profiles
      3. Assemble upper and lower frames
      4. Interlock upper and lower frames
    2. Y-axis
      1. Side plates to upper frame
      2. Y-axis motors, idlers and pulleys to side plates
      3. Y-axis belt tensioners and end-stop mounts
      4. Y-axis HTD5M belts
    3. X-axis and Z-axis
      1. Rails to bridge beams
      2. X-axis tensioner and end-stop mount to lower bridge beam
      3. Bridge beams to side plates
      4. Rod bearings to carriage
      5. Carriage to bridge beams
      6. X-axis motor, idlers and pulley to carriage
      7. X-axis HTD5M belt
      8. Acme nut and rails to carriage slider
      9. Acme rod and vertical slider to carriage
      10. Z motor mount and X-axis cable chain
      11. Y-axis cable chain
      12. Z stepper motor, pulleys and belt
    4. Stepper motors and end-stops
      1. Extend stepper motor wires
        1. Y-axis 1
        2. Y-axis 2
        3. X-axis
        4. Z-axis
      2. End-stops and end-stop wires
        1. X-axis (max)
        2. X-axis (min)
        3. Y-axis (max)
        4. Y-axis (min)
        5. Z-axis (max)
      3. Stepper motor and end-stop cable management
        1. Y-axis steppers and X-axis end-stops
        2. X-axis stepper, Z-axis stepper and Z-axis end-stop
    5. Router
      1. Attach router to carriage
      2. Router cable management
    6. Electronic boxes
      1. Small electronic box
      2. Large electronic box
    7. Electrical wiring and connect components
      1. Main power supply
      2. Prepare power to steppers and connect fans and LED
      3. Assemble stepper motor drivers and tune VRef
      4. Attach Arduino and solder USB cable
      5. Stepper and end-stop cable management to small electronic box
      6. Connect steppers to CNC shield
      7. Connect end-stops to CNC shield
      8. Set microstepping
      9. Router cable management and connect to main power supply
      10. Final test of electrical wiring
    8. Wasteboard
      1. Cut out wasteboard
      2. Attach wasteboard to CNC
    9. Dust shoe (updated Feb 4, 2022)
  4. Software
    1. Install CNC software (grbl) on Arduino Uno
      1. Install Arduino Software (IDE)
      2. Install GRBL
    2. G-Code sender
      1. Install G-Code sender
      2. Connect G-Code sender to GRBL
      3. Adjust GRBL configuration
        1. Enable end-stops/hard limits
        2. Calculate and set travel resolutions
        3. Other configurations
  5. Final notes

License

The following license is included when buying Ivan Miranda's blueprints of the CNC machine:

Everything that is in these files that I produced myself, apart from reselling the files, is allowed.
You can print and sell parts, sell machines, sell courses to build the machine. Modify the parts and post 
them for free, as long as you don’t sell the files and keep this license on everything you make with the 
files and credit me, we’re good. No DRM or anything, you are even allowed to repost the files as long as 
they’re kept free. Why buy this then? To support me and keep me encouraged to do more projects like this. 

Ivan does an amazing job putting these DIY builds together. I've posted his STL-files in this repository to simplify the build, but PLEASE buy his blueprints here: https://ivanmiranda.com/products/3d-printed-cnc. It's only $25 and helps him to continue build and share his awesome projects. Also, you will get access to a Discord channel that is really useful, where you can ask questions to a lot of people who have already built the machine.

Also, the Z-axis end-stop trigger, the ordinary end-stops and the rail supports all come from cello4's GitHub: https://github.com/4cello/mirandacnc-community.

Parts (bill of materials)

CLICK HERE TO OPEN THE BILL OF MATERIALS (BOM) MARKDOWN: Bill of materials

To simplify the build, I've created a separate markdown page with tables covering all parts needed to build the CNC-machine. The tables include a unique Item No. to easier refer to the parts in the guide. The tables also include images of all parts and .STL/.OBJ files of the parts that needs to be 3d-printed.

To get an even better understanding of how all the parts are used, I've created a detailed spreadsheet with comments:

To be able to continue with the build, you need to buy and 3d-print all needed parts found in the bill of materials.

Build the CNC machine

This section covers how all the parts is put together to build the CNC machine.

All the measurements, distances and a complete overview of how everything comes together can be found in the main Fusion 360 CAD design. It can be downloaded here:

Please note that the main Fusion 360 design is quite messy, which is one of the reasons why I've extracted the needed parts in a separate bill of materials.

Fusion 360 is a CAD program developed by Autodesk. It's free for personal use and can be downloaded here: https://www.autodesk.com/products/fusion-360/personal. After you've downloaded Fusion 360, import fusion_360_cad_files.f3z to load the main CAD design. This can also come in handy if you need to adjust some of the 3d-printed parts.

Main frame

Drill holes in 900 mm profiles

The main frame consists of two separate frames, the lower and the upper frame. The two frames are kept together using threaded rods, washers and nuts. To enable the threaded rods to slide through the aluminium profiles, holes needed to be drilled.

First, a sharpie was used to indicate where all the holes were going in the 900mm profiles (O07). This was done by using a set square and a penn. A bradawl and a hammer were then used to make indentations at the center of the holes.

holes_main_frame_1

A 9 mm drill-bit and a bench drill was used to drill the holes straight through the profiles.

holes_main_frame_1

holes_main_frame_1

To be able to access the nuts and tight them with a socket wrench, some holes (facing outwards, see Fusion360 CAD file) needed to be enlarged. A sharpie was used to mark all the holes that needed to be enlarged.

holes_main_frame_1

A step drill was then used to enlarge the holes holes to 20 mm. A tip is to measure the size of your socket wrench and keep the holes as small as possible, while you're still able to tighten the nuts. To be able to see which step you're aiming for on the step drill, attach a small piece of masking tape on the step above.

holes_main_frame_1

holes_main_frame_1

holes_main_frame_1

holes_main_frame_1

The edges were finally smoothed out using a round metal file.

holes_main_frame_1

holes_main_frame_1

holes_main_frame_1

Rails to 900 mm profiles

Before the upper and lower frames were assembled, two 600 mm MGN12H rails (O21) were attached to the 900 mm aluminium profiles (O07) of the upper frame. They were attached to the sides facing outwards and above the three 80 mm vertical beams (connecting the lower and upper frame). A tip is to place all the profiles as they should go to make sure that you're attaching the rails to the correct faces (see the red boxes on the image below). Also, be very careful when removing the MGN12H blocks (O22) from the rails.

attach_rails_to_beams_2

rails_main_frame_1

rails_main_frame_0

3x 3d-printed support tools (P25) were used to center the rails on the profiles. A 57 mm wood block were cut out and used to attach the rails at the same distance from the end of the profiles on both sides. The rails were then clamped to the profiles.

rails_main_frame_2

rails_main_frame_3

rails_main_frame_4

rails_main_frame_5

A bradawl and a hammer were then used to make indentations at the center of the holes. Cutting fluid was applied and a 2 mm drill was used to drill all the holes.

rails_main_frame_6

rails_main_frame_7

rails_main_frame_8

rails_main_frame_9

rails_main_frame_10

rails_main_frame_11

Cutting fluid was then applied once more on the drilled holes and a M3 drill tap was used to create threads in the holes.

rails_main_frame_12

rails_main_frame_13

Finally, the rails were attached using 48x 16 mm M3 screws (S03).

rails_main_frame_14

rails_main_frame_15

rails_main_frame_16

rails_main_frame_17

Assemble upper and lower frames

The two frames were assembled using the 4x 717 mm M8 threaded rods (T03), 8x (20mm, 10mm, 2mm) washers (W04) and 8x M8 lock nuts (N03).

The profiles were first placed in their correct place and clamps were used to keep the profiles aligned. I used two jointed spanners (one one each side) to lock everything in place, but you can also use two socket wrenches. Just make sure that the bits fit into the drilled holes.

assemble_frames_1

assemble_frames_3

assemble_frames_2

assemble_frames_4

assemble_frames_5

assemble_frames_6

assemble_frames_7

Interlock upper and lower frames

The upper and lower frames and the 8x 80 mm vertical aluminium beams (O06) were first layed out in their correct place. The 803 mm horizontal bridge beams (used later in the tutorial) (O05) and clamps were then used to align the frames on top of each other.

assemble_frames_9

assemble_frames_10

8x 120 mm M8 threaded rods (T02), 16x (20mm, 10mm, 2mm) washers (W04) and 16x M8 lock nuts (N03) were then used to interlock the upper and lower frames, with the 80 mm vertical aluminium profiles in between.

assemble_frames_8

assemble_frames_12

assemble_frames_11

assemble_frames_13

Y-axis

Side plates to upper frame

Before attaching the side plates, the MGN12H blocks (O22) were added back onto the rails, 2x on each side. Be careful when sliding them onto the rails, there are multiple small bearing balls that easily fall out of the blocks.

assemble_side_plates_1

assemble_side_plates_2

The left (P20) and right (P29) side plates where then attached to the blocks using 16x 20 mm M3 screws (S04) (8x on each side plate). Make sure to attach the plates on the correct side (see images below).

I had to redesign the left side plate and reprint it later in the build (after the images were taken). Therefore, the left side plate seen in the upcoming images look a bit different than the one used (see next image for the left side plate used).

assemble_side_plates_3

assemble_side_plates_4

assemble_side_plates_5

assemble_side_plates_6

assemble_side_plates_7

assemble_side_plates_8

Y-axis motors, idlers and pulleys to side plates

Each idler were made up out of 1x idler blocker (P16), 2x 60 mm fully threaded M8 screws (S15), 6x 698zz bearings (O01) and 8x (15 mm x 8.5 mm x 1.5mm) washers (W03) (2x closest to the idler blocker and 6x closest to the side plate). The idlers were then attached to each side plate using two M8 nuts (N03). Make sure that the bearings are spinning freely.

attach_side_plate_motors_1

attach_side_plate_motors_2

As I designed and added the idler blocker later on in the build, some of the images doesn't have it and they also have 3x washers instead of 1x washer closest to the screw head. I left these images anyways in the guide so you can see how it looks when you attach the idlers, but please ignore the wrong number of washers. Also ignore all the other things around the idlers in the upcoming 2 images, they are taken later on in the build.

attach_side_plate_motors_3_0

attach_side_plate_motors_3_1

Should be idler blockers and a different number of washers in the upcoming images.

attach_side_plate_motors_3

attach_side_plate_motors_4

attach_side_plate_motors_5

attach_side_plate_motors_6

attach_side_plate_motors_7

To attach the stepper motors to the side plates, the 4x M3 screws (S07) locking the gear box to the motor were removed. Save these as they will be used later on to attach the power supply and Arduino to the electronic boxes.

attach_side_plate_motors_1

attach_side_plate_motors_1

The 2x geared stepper motors (E18) were then inserted into the large holes on the side plates, facing inwards. 4x 40 mm M3 screws (S06) and 4x M3 washers (W05) were used to lock each stepper motor to the side plates (I forgot to add the washers in the images below, therefore they're not visible). The motors should be attached so that the cables are facing in the direction of the two bridge beams (i.e. the longer vertical surface on the side plates).

attach_side_plate_motors_1

attach_side_plate_motors_1

attach_side_plate_motors_1

attach_side_plate_motors_1

attach_side_plate_motors_1

1x HTD5M timing pulley (O18) was attached to each motor shaft using set screws.

attach_side_plate_motors_1

attach_side_plate_motors_1

attach_side_plate_motors_1

attach_side_plate_motors_1

Y-axis belt tensioners and end-stop mounts

2x fixed belt tensioners (P19, P28) were attached to the longer aluminium profiles of the upper frame using 4x 20mm M5 screws (S12) (2x for each fixed belt tensioner). When aligning the fixed belt tensioners, make sure that the "belt opening" is pointing in the direction of the rails (1x fixed belt tensioner for each rail). Also make sure that the fixed belt tensioners are positioned on the correct side of the rail (see images). Similar to before, a bradawl and a hammer were used to make indentations at the center of the holes. Cutting fluid was applied and a 4 mm drill was used to drill the holes, followed by a M5 drill tap.

attach_tensioners_and_belts_12

attach_tensioners_and_belts_13

attach_tensioners_and_belts_14

attach_tensioners_and_belts_15

attach_tensioners_and_belts_16

attach_tensioners_and_belts_17

attach_tensioners_and_belts_18

2x belt tension sliders (P17, P26) were attached on the opposite side of the fixed belt tensioners, ontop of the aluminium profile, using 4x 20mm M5 screws (S12). To get them aligned at the exact same place on both sides, a 100 mm distance was cut out and a flat support was clamped to the inner side of the profile. The same drill and tap size were used as for the fixed belt tensioners (4mm drill, M5 drill tap). Make sure that the belt tension sliders are pointing outwards.

attach_tensioners_and_belts_19

attach_tensioners_and_belts_20

attach_tensioners_and_belts_21

attach_tensioners_and_belts_22

attach_tensioners_and_belts_23

attach_tensioners_and_belts_24

attach_tensioners_and_belts_25

attach_tensioners_and_belts_26

attach_tensioners_and_belts_27

2x end-stop mounts (P08) were then attached to the same side as the belt tension sliders using 4x 20mm M5 screws (S12), facing outwards and aligned with the rails. The same drill and tap size were used as for the fixed belt tensioners (4mm drill, M5 drill tap).

attach_tensioners_and_belts_1

attach_tensioners_and_belts_2

attach_tensioners_and_belts_3

attach_tensioners_and_belts_4

attach_tensioners_and_belts_5

attach_tensioners_and_belts_6

attach_tensioners_and_belts_7

attach_tensioners_and_belts_8

attach_tensioners_and_belts_9

attach_tensioners_and_belts_10

attach_tensioners_and_belts_11

The belt tensioners (P18, P27) were loosely attached to the belt tension sliders using 2x 60 mm fully threaded M8 screws (S15), 2x M8 nuts(N03) and 2x (20mm x 10mm x 2mm) washers (W04).

attach_tensioners_and_belts_28

attach_tensioners_and_belts_29

Y-axis HTD5M belts

The HTD5M belt (O17) was first inserted into one of the fixed belt tensioners using a flat screw driver. It was then stretched along the aluminium profile, below the first idler, around the timing pulley, below the second idler and all the way to the belt tensioner.

attach_tensioners_and_belts_30

attach_tensioners_and_belts_31

attach_tensioners_and_belts_32

attach_tensioners_and_belts_33

attach_tensioners_and_belts_34

A scissor was used to cut the belt at an appropriate length. The loose end was then inserted into the belt tensioner using a flat screw driver and the belt was stretched by tightning the M8 nut.

attach_tensioners_and_belts_35

attach_tensioners_and_belts_36

attach_tensioners_and_belts_37

attach_tensioners_and_belts_38

attach_tensioners_and_belts_39

Make sure that the belt is not too loose and not too tight.

attach_tensioners_and_belts_40

attach_tensioners_and_belts_41

Repeat on the other side.

X-axis and Z-axis

Rails to bridge beams

The last two 600 mm MGN12H rails (O21) were attached to two of the 803 mm aluminium bridge beams (O05, used for the X-axis). First, the MGN12H blocks (O22) were carefully removed from the rails.

attach_rails_to_beams_1

attach_rails_to_beams_2

The same 100 mm distance used to align the belt tension sliders were used to align the rails. Because they will be off center by 3 mm, make sure that you later attach the bridge beams to the side plates in a way so the rails line up.

The same 3d-printed support tools (P25) used to align the rails on the 900 mm aluminium profiles were used here as well. Everything was clamped into position. A bradawl and a hammer were used to make indentations and a 2 mm drill and a M3 drill tap was used to make the screw holes.

attach_rails_to_beams_3

attach_rails_to_beams_4

attach_rails_to_beams_5

attach_rails_to_beams_6

attach_rails_to_beams_7

attach_rails_to_beams_8

attach_rails_to_beams_9

attach_rails_to_beams_10

attach_rails_to_beams_11

The rails were finally attached using 16 mm M3 screws (S03) and the MGN12H rail blocks (O22) were gently slided back onto the rails.

attach_rails_to_beams_12

attach_rails_to_beams_13

attach_rails_to_beams_14

attach_rails_to_beams_15

X-axis tensioner and end-stop mount to lower bridge beam

The fixed tensioner (P28) and end-stop mount (P08) were attached to the lower bridge beam in the same fashion as on the 900 mm aluminium profiles, using 4x 20mm M5 screws (S12). When aligning the fixed tensioner, make sure that the "belt opening" is pointing in the direction of the rail. A bradawl and a hammer were used to make indentations at the center of the holes. Cutting fluid was applied and a 4 mm drill was used to drill the holes, followed by a M5 drill tap.

attach_tensioners_to_beams_1

attach_tensioners_to_beams_2

attach_tensioners_to_beams_3

attach_tensioners_to_beams_4

attach_tensioners_to_beams_5

attach_tensioners_to_beams_6

attach_tensioners_to_beams_7

attach_tensioners_to_beams_8

attach_tensioners_to_beams_9

attach_tensioners_to_beams_10

attach_tensioners_to_beams_11

attach_tensioners_to_beams_12

Bridge beams to side plates

All three bridge beams (O05) were then inserted into the slots on the side plates. Make sure that the two beams with the rails are on top of each other, with the rails pointing outwards. Also, make sure that you insert them in the correct orientation, so that the rails are lined up (due to the rails being 3 mm off center).

attach_beams_to_side_plates_1

attach_beams_to_side_plates_1

attach_beams_to_side_plates_1

attach_beams_to_side_plates_1

When the bridge beams were aligned, the blocker clips (P21, P22, P23, P30, P31, P32) were placed in their correct place and a sharpie was used to mark the center of the holes to be drilled. Similar to before, a bradawl and a hammer were used to make indentations at the center of the holes.

attach_beams_to_side_plates_1

attach_beams_to_side_plates_1

attach_beams_to_side_plates_1

attach_beams_to_side_plates_1

A 7 mm drill bit was used to drill the holes. As these holes were going straight through the profiles, a bench drill was used for precision. A metal file was used to remove all excess metal around the holes.

attach_beams_to_side_plates_1

attach_beams_to_side_plates_1

The bridge beams were then inserted into the slots on the side plates once more, along with all the blocker clips. 2x 140 mm threaded M5 rod (T01) was inserted through the bottom two beams and 2x 60 mm M5 (S14) screws was inserted through the top bridge beam. It was all tightened using M5 nuts (N02).

attach_beams_to_side_plates_1

attach_beams_to_side_plates_1

attach_beams_to_side_plates_1

attach_beams_to_side_plates_1

attach_beams_to_side_plates_1

attach_beams_to_side_plates_1

attach_beams_to_side_plates_1

Rod bearings to carriage

Before attaching the carriage (P07) to the bridge beams, two KFL08 rod bearings (O19) were attached on the top and the bottom of the carriage (inside) using 4x 20 mm M5 screws (S12) and 4x M5 nuts (N02). A tip is to temporarily use the acme rod (used in an upcoming step) to vertically align the two bearings.

assemble_carriage_1

assemble_carriage_2

assemble_carriage_3

assemble_carriage_4

assemble_carriage_5

Carriage to bridge beams

The carriage was attached to the 4x MGN12H blocks (O22) on the bridge beams, using 16x 25 mm M3 screws (S05).

attach_carriage_to_beams_1

attach_carriage_to_beams_2

attach_carriage_to_beams_3

attach_carriage_to_beams_4

X-axis motor, idlers and pulley to carriage

Each idler were made up out of 1x 60 mm fully threaded M8 screw (S15), 3x 698zz bearings (O01) and 4x (15 mm x 8.5 mm x 1.5mm) washers (W03) (1 closest to the idler blocker and 3 closest to the side plate). 2x idlers were then attached to each side plate using 2x M8 nuts (N03). Make sure that the bearings are spinning freely.

attach_side_plate_motors_1

attach_side_plate_motors_2

As I designed and added the idler blocker later on in the build, some of the images doesn't have it and they also have 3 washers instead of 1 washer closest to the screw head. I left these images anyways in the guide so you can see how it looks when you attach the idlers, but please ignore the wrong number of washers. Also ignore all the other things around the idlers in the upcoming image, they are taken later on in the build.

attach_idlers_motor_to_carriage_3

Should be idler blockers and a different number of washers in the upcoming images.

attach_idlers_motor_to_carriage_3

attach_idlers_motor_to_carriage_4

attach_idlers_motor_to_carriage_5

To attach the stepper motor to the carriage, the 4x M3 screws locking the gear box to the motor were removed.

attach_idlers_motor_to_carriage_6

attach_idlers_motor_to_carriage_7

attach_idlers_motor_to_carriage_8

The stepper motor was then inserted into the large hole on the carriage, facing towards the bridge beams/idlers. 4x 40 mm M3 screws (S06) and 4x M3 washers (W05) were used to lock the stepper motor onto the carriage. The motor should be attached so that the cables are facing upwards.

attach_idlers_motor_to_carriage_9

attach_idlers_motor_to_carriage_10

attach_idlers_motor_to_carriage_11

1x HTD5M timing pulley (O18) was attached to the motor shaft using set screws.

attach_idlers_motor_to_carriage_12

attach_idlers_motor_to_carriage_13

X-axis HTD5M belt

The HTD5M belt (O17) was first inserted into the fixed belt tensioner using a flat screw driver. It was then stretched along the aluminium profile, below the first idler, around the timing pulley, below the second idler and all the way to the other side.

The belt was cut at an appropriate length and inserted into the belt tensioner (P27) using a flat screw driver.

attach_x_axis_belt_1

attach_x_axis_belt_2

attach_x_axis_belt_3

attach_x_axis_belt_4

attach_x_axis_belt_5

The belt tensioner was then attached to the side plate using 1x 60mm fully threaded M8 screw (S15), 1x M8 nut (N03) and 1x (20mm x 10mm x 2mm) washer (W04). The M8 screw in the image is not fully threaded as I lost the one I was suppose to use and had to use another one, so please ignore :)

attach_x_axis_belt_6

attach_x_axis_belt_7

Make sure that the belt is not too loose and not too tight.

attach_x_axis_belt_8

Acme nut and rails to carriage slider

1x acme nut (O03) was inserted from the outside, into the the center hole at the top of the vertical carriage slider (P36). It was locked in place using 4x 25mm M3 screws (S05).

assemble_carriage_6

assemble_carriage_6

assemble_carriage_7

assemble_carriage_8

2x smaller 200 mm MGN12H rails (O20) were then attached to the back of the vertical carriage slider. First, the MGN12H blocks (O22) were carefully removed from each rail. After that, the rails were screwed in place on the back of the vertical carriage slider using 16x 20 mm M3 screws (S04). The MGN12H blocks were then slided back on and each end were blocked using tape.

assemble_carriage_9

assemble_carriage_10

assemble_carriage_11

assemble_carriage_12

assemble_carriage_13

Acme rod and vertical slider to carriage

To attach the vertical slider to the carriage, 16x 25 mm M3 screws (S05) were first inserted into the holes on the carriage. You might need to "open up" the holes using a narrow tool (depending on the direction you 3d-printed the carriage).

assemble_carriage_17

assemble_carriage_18

assemble_carriage_19

1x acme rod (O02) was then inserted through the two KFL08 rod bearings and the acme nut, and the set screws on the bearings were tightened.

assemble_carriage_14

assemble_carriage_15

assemble_carriage_16

The vertical slider was finally attached to the carriage by attaching the previously mentioned 16x 25 mm M3 screws (S05) to the MGN12H blocks on the vertical slider.

assemble_carriage_20

assemble_carriage_21

Z motor mount and X-axis cable chain

The first step was to find a good length of the X-axis cable chain (O09). To simplify this process, the X-axis belt was removed to easier move the carriage along the X-axis.

assemble_carriage_22

The Z motor mount (P40) and the X-axis cable chain mount (P38) were then attached using 3x 25 mm M4 screws (S10), 3x M4 nuts (N01) and 3x (10mm x 5mm x 1mm) washers (W01).

assemble_carriage_23

assemble_carriage_24

assemble_carriage_25

assemble_carriage_26

assemble_carriage_27

assemble_carriage_28

assemble_carriage_29

assemble_carriage_30

They Z motor mount was then attached to the carriage using 2x 80mm M8 screws (S16), 2x M8 nuts (N03) and 1x (20mm x 10mm x 2mm) washers (W04). The vaccum mount was also inserted and attached to the right-side M8 screw. Please ignore the timing pulley attached to the acme rod in some of the images, it will be attached in a later step.

assemble_carriage_30

assemble_carriage_31

assemble_carriage_32

assemble_carriage_33

assemble_carriage_34

assemble_carriage_35

1x 1 meter cable chain (O09) were then clamped to the cable chain mount and to the back-side bridge beam. The carriage was then moved as far to the sides as possible. It's important that the chain doesn't touch any of the side plates when moved. In my case, I had to remove 3 links from the cable chain to get a good length of the chain.

assemble_carriage_36

assemble_carriage_37

assemble_carriage_38

assemble_carriage_39

assemble_carriage_39

The Z motor mount and cable chain mount were then disassembled and the cable chain was properly attached to the cable chain mount using 2x 25mm M4 screws (S10), 2x M4 nuts (N01) and 2x (10mm x 5mm x 1mm) washers (W01).

assemble_carriage_40

assemble_carriage_41

assemble_carriage_42

assemble_carriage_43

The Z motor mount and cable chain mount were then assembled again and attached to the carriage in the same fashion as before.

assemble_carriage_44

assemble_carriage_45

assemble_carriage_46

assemble_carriage_47

The carriage was move all the way to the right side plate and the cable chain was clamped to the lower back bridge beam.

assemble_carriage_48

assemble_carriage_49

A bradawl and a hammer were used to make indentations at the center of the two holes. Cutting fluid was applied and a 3 mm drill was used to drill the holes, followed by a M4 drill tap. The cable chain was then attached to the bridge beam using 2x 25 mm M4 screws (S10).

assemble_carriage_50

assemble_carriage_51

assemble_carriage_52

assemble_carriage_53

assemble_carriage_54

assemble_carriage_55

assemble_carriage_56

assemble_carriage_57

assemble_carriage_58

assemble_carriage_59

assemble_carriage_60

Finally, the X-axis belt was reattached and tightened.

assemble_carriage_61

Y-axis cable chain

The Y-axis cable chain (O09) was attached to the frame using 1x cable chain mount (P05) and 1x cable chain support (P06). The cable chain mount was clamped to the left side of the lower frame and aligned with the last vertial beam. A bradawl and a hammer were used to make indentations at the center of the two holes. Cutting fluid was applied and a 4 mm drill was used to drill the holes, followed by a M5 drill tap. The cable chain mount was then attached to the lower frame using 2x 20 mm M5 screws (S12).

assemble_cable_support_y_axis_1

assemble_cable_support_y_axis_2

assemble_cable_support_y_axis_3

assemble_cable_support_y_axis_4

assemble_cable_support_y_axis_5

The cable chain support was only attached to the lower frame for the cable chain to rest on. It was aligned and attached it at the center between the second and third vertical beam. Make sure that it does not go below the bottom frame!

In the same way as the cable chain mount, a bradawl and a hammer were used to make indentations at the center of the two holes. Cutting fluid was applied and a 4 mm drill was used to drill the holes, followed by a M5 drill tap. The support was then attached to the lower frame using 2x 20 mm M5 screws (S12).

assemble_cable_support_y_axis_6

assemble_cable_support_y_axis_6

assemble_cable_support_y_axis_7

assemble_cable_support_y_axis_8

assemble_cable_support_y_axis_9

assemble_cable_support_y_axis_10

assemble_cable_support_y_axis_11

The Y-axis cable chain (O09) was then attached to the left side plate (P20) and lower frame support using 4x 25 mm M4 screws (S10), 4x M4 nuts (N01) and 4x (10mm x 5mm x 1mm) washers (W01).

assemble_cable_support_y_axis_12

assemble_cable_support_y_axis_13

assemble_cable_support_y_axis_14

assemble_cable_support_y_axis_15

assemble_cable_support_y_axis_16

assemble_cable_support_y_axis_17

Z stepper motor, pulleys and belt

The non-geared NEMA17 stepper motor (E11) was attached to the Z-axis motor mount using 4x 8mm M3 screws (S08) and 4x M3 washers (W06). Make sure that the motor cable connector is pointing in the same direction as the opening of the X-axis cable chain.

1x 16 teeth GT2 timing pulley (O15) was then attached to the motor shaft and 1x 60 teeth GT2 timing pulley (O16) was attached to the acme rod. Both were locked in place using set screws. Make sure that they line up.

attach_z_stepper_pulleys_belt_1

attach_z_stepper_pulleys_belt_2

attach_z_stepper_pulleys_belt_3

attach_z_stepper_pulleys_belt_4

attach_z_stepper_pulleys_belt_5

attach_z_stepper_pulleys_belt_6

1x GT2 timing belt (O14) was looped around both timing pulleys and stretched. Before tightning the M3 screws and locking the motor into place, make sure that the belt is not too loose and not too tight.

attach_z_stepper_pulleys_belt_7

attach_z_stepper_pulleys_belt_8

attach_z_stepper_pulleys_belt_9

attach_z_stepper_pulleys_belt_10

Stepper motors and end-stops

Extend stepper motor wires

All 4 stepper motors (2x Y-axis, 1x X-axis and 1x Z-axis) get their power and movement instructions from the Arduino + CNC shield that in a later step will be attached in the small electronic box. Therefore, the stepper motor cables needed to be extended to reach through the cable chains all the way to the front of the machine, where the small electronic box will be located.

AWG22 cables (E08) of matching colors were used when increasing the length of the stepper motor cables. The same process was used for all the motors:

  1. The amount of wires needed to reach all the way to the electronic box was approximated and cut. Make sure to have an extra ~300 mm wire from the point where the wires exits the Y-axis cable chain, as this will be needed to reach the small electronic box.
  2. The ends of the original stepper wires and the extra AWG22 wires were stripped using a wire stripper.
  3. The colors of the original stepper wires and the extra AWG22 wires were matched up and the stripped ends of the wires were twisted around each other.
  4. The twisted wires where then locked in a steady position by a "third hand".
  5. Soldering grease was applied to the twisted wires and the wires were soldered together.
  6. 4 shrinking tubes (one per cable) were shrunk around the now soldered twisted wires, covering the soldering.
  7. A handful of larger shrinking tubes were shrunk around all 4 wires to keep them together.
  8. Finally, the wires were marked using tape and a penn, indicating which stepper motor the wires belonged to. This is important as it will help a lot later on, when the stepper motors are connected to the Arduino.

Y-axis 1

The extended wires of the first Y-axis stepper motor were cut at a length so that they reached through the lower front bridge beam (see red arrow on the next image) and through the Y-axis cable chain going to the front of the CNC machine.

solder_steppers_y_axis_1

solder_steppers_y_axis_2

solder_steppers_y_axis_3

solder_steppers_y_axis_4

solder_steppers_y_axis_5

solder_steppers_y_axis_6

solder_steppers_y_axis_7

solder_steppers_y_axis_8

solder_steppers_y_axis_9

solder_steppers_y_axis_10

solder_steppers_y_axis_10_1

Y-axis 2

The extended wires of the second Y-axis stepper motor were cut at a length so that they reached through the Y-axis cable chain going to the front of the CNC machine.

solder_steppers_y_axis_11

solder_steppers_y_axis_12

solder_steppers_y_axis_13

solder_steppers_y_axis_14

solder_steppers_y_axis_15

solder_steppers_y_axis_16

solder_steppers_y_axis_17

solder_steppers_y_axis_18

solder_steppers_y_axis_19

solder_steppers_y_axis_20

X-axis

I ran out of AWG22 wires when soldering the X-axis stepper motor cables, therefore you will see different type of cables in the upcoming images. Because of this, I had to insert the shrinking tubes before I soldered the cables. Please disregard this and follow the previous instructions.

The extended wire of the X-axis stepper motor were cut at a length so that they reached up and behind the Z-axis stepper motor, through the X-axis cable chain and through the Y-axis cable chain to the front of the CNC machine.

solder_steppers_x_axis_1.jpg

solder_steppers_x_axis_2.jpg

solder_steppers_x_axis_3.jpg

solder_steppers_x_axis_4.jpg

solder_steppers_x_axis_5.jpg

solder_steppers_x_axis_6.jpg

solder_steppers_x_axis_7.jpg

solder_steppers_x_axis_8.jpg

Z-axis

The non-geared NEMA17 motor used for the Z-axis had removable wires, in contrast to the 1:19 geared NEMA17 motors that had non-removable wires. The first step was therefore to connect the wires to the NEMA17 motor and cut of the connector on the other side using a scissor. Otherwise, the same procedure was followed as for the other motors.

The extended wires of the Z-axis stepper motor were cut at a length so that they reached through the X-axis cable chain and through the Y-axis cable chain to the front of the CNC machine.

solder_steppers_z_axis_1.jpg

solder_steppers_z_axis_2.jpg

solder_steppers_z_axis_3.jpg

solder_steppers_z_axis_4.jpg

solder_steppers_z_axis_5.jpg

solder_steppers_z_axis_6.jpg

solder_steppers_z_axis_7.jpg

solder_steppers_z_axis_8.jpg

solder_steppers_z_axis_9.jpg

solder_steppers_z_axis_9.jpg

End-stops and end-stop wires

End-stops are important, as they do not only enable you to home the CNC machine, but they also limit the CNC machine from moving past what is physically possible. When the end-stops are triggered, an alarm is fired and the machine automatically stops.

The wires used for end-stops were 0.75 mm^2 (E03).

X-axis (max)

A microswitch (E21) was attached to the thick X-axis (+) end-stop mount (P10) using 2x 12mm M3 screws (S02).

attach_endstoppers_x_axis_1

attach_endstoppers_x_axis_2

attach_endstoppers_x_axis_3

attach_endstoppers_x_axis_4

The end-stop mount was then pushed against the backside of the top bridge beam, which enabled the end-stop to trigger on the Z-axis stepper motor. The X-axis (carriage) was then moved to its maximum position and the end-stop mount was positioned in a way so that the end-stop triggered just before the X-axis reached its maximum position.

Please ignore the flexible conduit/hose in the next two images, it will be added in an upcoming step.

attach_endstoppers_x_axis_5

attach_endstoppers_x_axis_7

The end-stop mount was then clamped to the upper bridge beam and a small drill (-2 mm) was used to carefully make indentations at the center of the holes. The end-stop mount was then removed. Cutting fluid was applied and a 4 mm drill was used to drill the holes, followed by a M5 drill tap. The end-stop mount was then attached to the upper bridge beam using 2x 40 mm M5 screws (S13).

attach_endstoppers_x_axis_8

attach_endstoppers_x_axis_9

attach_endstoppers_x_axis_10

attach_endstoppers_x_axis_11

attach_endstoppers_x_axis_12

attach_endstoppers_x_axis_13

attach_endstoppers_x_axis_14

attach_endstoppers_x_axis_15

attach_endstoppers_x_axis_16

One black and one red 0.75 mm^2 wire (E03) were cut out at a length so that they reached from the X-axis max end-stop to the right side plate, through the top bridge beam and through the Y-axis cable chain to the front of the CNC machine. A handful of shrinking tubes (O24) were shrunk around the wires to keep them together.

attach_endstoppers_x_axis_17

attach_endstoppers_x_axis_18

attach_endstoppers_x_axis_19

One end of the wires were taped together and inserted through the upper bridge beam to the side plate on the other side.

attach_endstoppers_x_axis_20

attach_endstoppers_x_axis_21

attach_endstoppers_x_axis_22

A flexible conduit/hose (O13) was then cut out and the other side of the cables were inserted through the conduit. The flexible conduit was then inserted ~50 mm into the upper bridge beam and the other side was attached to the outside of the upper bridge beam using cable ties (O11).

attach_endstoppers_x_axis_23

attach_endstoppers_x_axis_24

attach_endstoppers_x_axis_25

The end of the wires were stripped and twisted. Two 2.8 mm spade connectors (E25) were then attached to the stripped wires using a plier. The red wire was then attached to C (Common terminal) pinout on the end-stop and the black cable was connected to the NO (Normally Open) pinout.

attach_endstoppers_x_axis_26

attach_endstoppers_x_axis_27

attach_endstoppers_x_axis_28

attach_endstoppers_x_axis_29

attach_endstoppers_x_axis_30

Finally, the open end of the wires were marked using tape (O23) and a penn, indicating which end-stop the cables belonged to. This is important as it will help a lot later on, when the end-stops are connected to the Arduino.

attach_endstoppers_x_axis_31

X-axis (min)

A microswitch (E21) was attached to the X-axis end-stop (-) mount (P08) using 2x 12mm M3 screws (S02).

attach_endstoppers_x_axis_32_0

attach_endstoppers_x_axis_32_1

attach_endstoppers_x_axis_32_2

One black and one red 0.75 mm^2 wire (E03) were cut out at a length so that they reached from the X-axis end-stop (-), around the left side plate, through the Y-axis cable chain to the front of the CNC machine. A handful of shrinking tubes (O24) were shrunk around the wires to keep them together.

attach_endstoppers_x_axis_32

attach_endstoppers_x_axis_33

attach_endstoppers_x_axis_34

The end of the wires were stripped and twisted. Two 2.8 mm spade connectors (E25) were then attached to the stripped wires using a plier. The red wire was then attached to C (Common terminal) pinout on the end-stop and the black cable was connected to the NO (Normally Open) pinout.

The wires were initially strapped around the lower front bridge beam (seen in the first two images), but as it turned out it blocked the belt tensioner. So they were instead strapped around the M8 tensioner screw, using a cable tie (O11).

attach_endstoppers_x_axis_36

attach_endstoppers_x_axis_37

attach_endstoppers_x_axis_38

Finally, the open end of the wires were marked using tape and a penn, indicating which end-stop the cables belonged to.

attach_endstoppers_x_axis_39

Y-axis (max)

The tall Y-axis end-stop (+) mount (P09) was clamped to the inner side of the upper frame and a sharpie was used to indicate the center of the holes. Note that this end-stop mount can probably be redesigned to gain an extra ~10 mm of Y-axis movement, something I will probably do in the future.

attach_endstoppers_y_axis_1

attach_endstoppers_y_axis_2

attach_endstoppers_y_axis_3

attach_endstoppers_y_axis_4

A bradawl and a hammer were then used to make indentations at the center of the holes. Cutting fluid was applied and a 4 mm drill was used to drill the holes, followed by a M5 drill tap. The end-stop mount was then attached to the inside of the upper frame using 2x 20 mm M5 screws (S12).

attach_endstoppers_y_axis_5

attach_endstoppers_y_axis_6

attach_endstoppers_y_axis_7

attach_endstoppers_y_axis_8

attach_endstoppers_y_axis_9

attach_endstoppers_y_axis_10

attach_endstoppers_y_axis_11

attach_endstoppers_y_axis_12

One black and one red 0.75 mm^2 wire (E03) were cut out at a length so that they reached from the Y-axis end-stop (+) and through the 900 mm aluminium profile of the upper frame to the front of the CNC machine.

attach_endstoppers_y_axis_13

attach_endstoppers_y_axis_14

attach_endstoppers_y_axis_15

A microswitch (E21) was attached to the tall Y-axis end-stop (+) mount using 2x 12mm M3 screws (S02).

attach_endstoppers_y_axis_17

attach_endstoppers_y_axis_18

attach_endstoppers_y_axis_19

A flexible conduit/hose (O13) was then cut out and the wires were inserted through the conduit. The flexible conduit was then inserted ~50 mm into the 900 mm aluminium profile of the upper frame. The other side was bent around and attached to the outside of the upper frame using cable ties (O11).

attach_endstoppers_y_axis_20

attach_endstoppers_y_axis_21

attach_endstoppers_y_axis_22

The end of the wires were stripped and twisted. Two 2.8 mm spade connectors (E25) were then attached to the stripped wires using a plier. The red wire was then attached to C (Common terminal) pinout on the end-stop and the black cable was connected to the NO (Normally Open) pinout.

attach_endstoppers_y_axis_23

attach_endstoppers_y_axis_24

Finally, the open end of the wires were marked using tape and a penn, indicating which end-stop the cables belonged to.

attach_endstoppers_y_axis_16

Y-axis (min)

A microswitch (E21) was attached to the Y-axis end-stop (-) mount (P08) using 2x 12mm M3 screws (S02).

attach_endstoppers_y_axis_25

attach_endstoppers_y_axis_26

attach_endstoppers_y_axis_27

One black and one red 0.75 mm^2 wire (E03) were cut out at a length so that they reached from the Y-axis end-stop (-) and to the front of the CNC machine.

The end of the wires were stripped and twisted. Two 2.8 mm spade connectors (E25) were then attached to the stripped wires using a plier. The red wire were then attached to C (Common terminal) pinout on the end-stop and the black cable was connected to the NO (Normally Open) pinout.

attach_endstoppers_y_axis_28

attach_endstoppers_y_axis_29

attach_endstoppers_y_axis_30

attach_endstoppers_y_axis_31

A flexible conduit/hose (O13) was cut out and the wires were inserted through the conduit. The flexible conduit was attached to the outside of the upper frame using cable ties (O11).

attach_endstoppers_y_axis_33

attach_endstoppers_y_axis_34

attach_endstoppers_y_axis_32

attach_endstoppers_y_axis_35

Finally, the open end of the wires were marked using tape and a penn, indicating which end-stop the cables belonged to.

Z-axis (max)

The main purpose of the Z-axis end-stop (+) is, apart from homing the machine, to limit the CNC machine from moving past what the length of the rails allow. As the MGN12H blocks contains a lot of small bearing balls, there's a high risk of them falling out if the blocks move past the rail.

To reduce the complexity and amount of wires, I chose not to include a Z-axis end-stop (-), as you are likely to mill straight through your waste board before there's a risk of moving past the Z-axis min limit. But if you want to add a Z-axis min end-stop, just repeat the process in this section with the new switch flipped around.

First, the vertical carriage slider was moved upwards to its maximum point, where the MGN12H blocks are just about to move past the limit of the rails. The Z-axis end-stop trigger (P39) was then pressed against the outside of the vertical carriage slider and a sharpie was used to mark the center of the holes.

attach_endstoppers_z_axis_1

attach_endstoppers_z_axis_2

attach_endstoppers_z_axis_3

A 2.5 mm drill was used to drill the holes into the vertical carriage slider. A tip is to mark the drill depth needed using tape. The Z-axis end-stop trigger was then attached to the vertical carriage slider using 2x 12 mm M3 screws (S02).

attach_endstoppers_z_axis_4

attach_endstoppers_z_axis_5

attach_endstoppers_z_axis_6

attach_endstoppers_z_axis_7

A microswitch (E21) was pressed against the carriage and positioned and aligned to be triggered by the maximum state of the Z-axis end-stop trigger.

attach_endstoppers_z_axis_8

attach_endstoppers_z_axis_9

A 2.5 mm drill was used to drill the first hole into the carriage and the microswitch was attached to the carriage using 1x 12 mm M3 screw (S02). After the microswitch was locked into position, the second hole was drilled and the second 12 mm M3 screw (S02) was attached.

attach_endstoppers_z_axis_10

attach_endstoppers_z_axis_11

attach_endstoppers_z_axis_12

One black and one red 0.75 mm^2 wire (E03) were cut at a length so that they reached over the top bridge beam, through the X-axis cable chain and through the Y-axis cable chain to the front of the CNC machine. A handful of shrinking tubes (O24) were shrunk around the wires to keep them together.

attach_endstoppers_z_axis_13

attach_endstoppers_z_axis_14

attach_endstoppers_z_axis_15

The end of the wires were stripped and twisted. Two 2.8 mm spade connectors (E25) were then attached to the stripped wires using a plier. The red wire was then attached to C (Common terminal) pinout on the end-stop and the black wire was connected to the NO (Normally Open) pinout.

attach_endstoppers_z_axis_16

attach_endstoppers_z_axis_17

attach_endstoppers_z_axis_18

The wires were strapped around the M8 screw keeping the Z motor mount attached to the carriage, using a cable tie (O11).

Finally, the open end of the wires were marked using tape and a penn, indicating which end-stop the cables belonged to.

attach_endstoppers_z_axis_19

attach_endstoppers_z_axis_20

Stepper motor and end-stop cable management

To keep a nice structure of all the wires, braided cable sleeves (O08) and flexible conduits/hoses (O13) were used.

Y-axis steppers and X-axis end-stops

First, the wires from the right-side Y-axis stepper motor were inserted into a small flexible conduit and pushed through the lower bridge beam closest to the carriage.

stepper_motor_cable_management_1

stepper_motor_cable_management_3

stepper_motor_cable_management_4

The wires from the two geared Y-axis stepper motors and the two X-axis end-stops were bundled together into the same cable sleeve.

stepper_motor_cable_management_6

stepper_motor_cable_management_6_1

stepper_motor_cable_management_6_2

stepper_motor_cable_management_5

stepper_motor_cable_management_6_3

To simplify pushing the wires and the cable sleeve through the cable chain, the wires were taped together, leaving no loose ends to get stuck in the cable chain. This was needed as the wires were longer than the cable sleeve (to reach all the way to the small electronic box in the front of the CNC machine).

A cable tie (O11) was used to close the entrence of the cable sleeve.

stepper_motor_cable_management_6_4

stepper_motor_cable_management_6_5

stepper_motor_cable_management_6_6

X-axis stepper, Z-axis stepper and Z-axis end-stop

First, the wires from the X-axis stepper motor were inserted into a flexible conduit (O13). The conduit was then bent over the upper bridge beam, strapped to the vaccum mount and Z motor mount, and then pushed behind the Z-axis stepper motor.

stepper_motor_cable_management_9

stepper_motor_cable_management_10

stepper_motor_cable_management_11

stepper_motor_cable_management_12

The wires from the X-axis stepper, Z-axis stepper and the Z-axis end-stop were bundled together into the same cable sleeve. The cable sleeve was cut at a length so that it reached through the X-axis cable chain, around the left side-plate and through the Y-axis cable chain.

To simplify pushing the wires through the cable chains, the wires were taped together, leaving no loose ends to get stuck in the cable chains. This was needed as the wires were longer than the cable sleeve (to reach all the way to the small electronic box in the front of the CNC machine).

A cable tie (O11) was used to close the entrence of the cable sock.

stepper_motor_cable_management_13

stepper_motor_cable_management_13_1

stepper_motor_cable_management_13_2

stepper_motor_cable_management_13_3

stepper_motor_cable_management_13_4

stepper_motor_cable_management_13_5

stepper_motor_cable_management_13_6

stepper_motor_cable_management_13_7

stepper_motor_cable_management_13_8

A cable tie (O11) was used to strap the cable sleeve to the left side-plate.

stepper_motor_cable_management_13_9

Router

Attach router to carriage

A Makita RT0700CJ (E20) trimming router was used as I was not able to get my hands on the Makita RT0700C that Ivan is using. To my knowledge, the RT0700CJ is just an upgraded European version of the RT0700C, with the same dimensions.

The trimming router was locked in place by using the router bracket (P24), 4x 40mm M5 screws (S13), 4x M5 nuts (N02) and 4x (10mm x 5mm x 1mm) washers (W01).

attach_router_to_carriage_1

attach_router_to_carriage_2

attach_router_to_carriage_3

attach_router_to_carriage_4

attach_router_to_carriage_6

attach_router_to_carriage_7

Router cable management

NOTE: THIS PART INCLUDES WIRING OF HIGH VOLTAGE ELECTRICITY THAT CAN BE LETHAL IF NOT DONE PROPERLY. THE COLORS OF THE CABLES CAN VARY DEPENDING ON REGION/COUNTRY AND YOUR COMPONENTS/PINOUT NUMBERS MIGHT LOOK DIFFERENT. BEFORE YOU CONNECT THE POWER CORD TO THE POWER OUTLET, YOU MUST CONSULT WITH A LICENSED ELECTRICIAN TO MAKE SURE THAT EVERYTHING IS PROPERLY WIRED AND THAT IT IS IN LINE WITH YOUR LOCAL LEGISLATIONS.

To be able to easily replace the trimming router in the future, a power plug (E04) and socket were added (E05).

router_cable_management_23

First, the router's power cord was cut and stripped at an appropriate length to reach behind the X-axis cable chain mount. A flexible conduit (O13) was cut out at an appropriate length and the power cord closest to the router was inserted into the conduit. The end of the power cord and the inside wires were then stripped and twisted.

router_cable_management_1

router_cable_management_2

router_cable_management_3

The power plug was opened up and the wires were connected. The built-in strain relief was then tightened around the cable before the plug was closed again.

router_cable_management_4

router_cable_management_5

router_cable_management_6

router_cable_management_7

router_cable_management_8

The rest of the power cord was inserted through the Y-axis cable chain, around the left side plate (under the cable tie) and through the X-axis cable chain. Getting the power cord through the X-axis cable chain was quite tricky due to the friction of the rubber cable. A cable tie (O11) was therefore attached to the top of the cable and used to pull the cable through the cable chain.

router_cable_management_9

router_cable_management_10

router_cable_management_11

router_cable_management_12

router_cable_management_13

router_cable_management_14

router_cable_management_15

The power cord was pulled through the cable chains and adjusted to an appropriate length to reach behind the X-axis cable chain mount. The end of the cable and the inside wires were then stripped and twisted.

router_cable_management_17

router_cable_management_19

The power socket was opened and the wires were attached to the terminals inside. The built-in strain relief was then tightened around the cable before the socket was closed again.

router_cable_management_16

router_cable_management_18

router_cable_management_20

router_cable_management_21

router_cable_management_22

The plug and socket were connected and strapped to the back of the X-axis cable chain mount using cable ties (O11). The flexible conduit with the router power cord inside was strapped to the stepper motor flexible conduit using cable ties (O11). Make sure that it doesn't touch and drag along the upper bridge beam.

router_cable_management_23

router_cable_management_24

Electronic boxes

Two electronic boxes were attached to the front side of the CNC machine, a large box to encapsulate the power supply and a small box to encapsulate the Arduino and the CNC shield.

Small electronic box

The small electronic box consisted of 4 parts (P02, P04, P13, P15). The two middle parts were clamped together on the front-left side of the frame, closest to the Y-axis cable chain. A finger was used to feel that the two parts were perfectly lined up.

Make sure to have enought space on the left side of the box for the all the stepper motor wires, end-stop wires and router power cable to enter the box (the vertical beam might block if you attach it too far to the left). Also make sure that the two holes are pointing to the left.

attach_small_electronic_box_1

attach_small_electronic_box_2

attach_small_electronic_box_3

The front-middle part (P13) was attached first. A small 2 mm drill was used to make indentations at the center of the holes. Cutting fluid was applied and a 3 mm drill was used to drill the holes, followed by a M4 drill tap. The front-middle and front part was then attached to the frame using 4x 40mm M4 screws (S11).

attach_small_electronic_box_4

attach_small_electronic_box_5

attach_small_electronic_box_6

attach_small_electronic_box_7

attach_small_electronic_box_8

attach_small_electronic_box_9

attach_small_electronic_box_10

To attach the back-middle part (P02), the whole CNC machine had to be pushed partly over the edge of the working table to be able to drill on the inside of the frame. The machine was firmly clamped to the table.

The back-middle part was again clamped to the frame and aligned with the now attached front-middle part. A small 2 mm drill was used to make indentations at the center of the holes. Cutting fluid was applied and a 3 mm drill was used to drill the holes, followed by a M4 drill tap. The back-middle and back part was then attached to the frame using 4x 25mm M4 screws (S10).

attach_small_electronic_box_11

attach_small_electronic_box_12

attach_small_electronic_box_13

attach_small_electronic_box_14

attach_small_electronic_box_15

attach_small_electronic_box_16

Large electronic box

As the small box, the large electronic box consisted of 4 parts (P01, P03, P12, P14). The two middle parts were clamped together to the right of the small box. A finger was used to feel that the two parts were perfectly lined up.

Make sure that the hole is pointing to the left.

attach_large_electronic_box_1

attach_large_electronic_box_1_1

The front-middle part (P12) was attached first. A small 2 mm drill was used to make indentations at the center of the holes. Cutting fluid was applied and a 3 mm drill was used to drill the holes, followed by a M4 drill tap. The front-middle and front part was then attached to the frame using 4x 40mm M4 screws (S11).

attach_large_electronic_box_2

attach_large_electronic_box_3

attach_large_electronic_box_4

attach_large_electronic_box_5

attach_large_electronic_box_6

attach_large_electronic_box_7

attach_large_electronic_box_8

To attach the back-middle part (P01), the whole CNC machine had to be pushed partly over the edge of the working table to be able to drill on the inside of the frame. The machine was firmly clamped to the table.

The back-middle part was again clamped to the frame and aligned with the now attached front-middle part. A small 2 mm drill was used to make indentations at the center of the holes. Cutting fluid was applied and a 3 mm drill was used to drill the holes, followed by a M4 drill tap. The back-middle and back part was then attached to the frame using 4x 25mm M4 screws (S10).

attach_large_electronic_box_9

attach_large_electronic_box_10

attach_large_electronic_box_11

attach_large_electronic_box_12

attach_large_electronic_box_13

attach_large_electronic_box_14

attach_large_electronic_box_15

Electrical wiring and connect components

Main power supply

NOTE: THIS PART INCLUDES WIRING OF HIGH VOLTAGE ELECTRICITY THAT CAN BE LETHAL IF NOT DONE PROPERLY. THE COLORS OF THE CABLES CAN VARY DEPENDING ON REGION/COUNTRY AND YOUR COMPONENTS/PINOUT NUMBERS MIGHT LOOK DIFFERENT. BEFORE YOU CONNECT THE POWER CORD TO THE POWER OUTLET, YOU MUST CONSULT WITH A LICENSED ELECTRICIAN TO MAKE SURE THAT EVERYTHING IS PROPERLY WIRED AND THAT IT IS IN LINE WITH YOUR LOCAL LEGISLATIONS.

The large electronic box was detached from the frame.

The 200W power supply (E02) was then attached to the back panel of the larger electronic box using 4x 5mm M3 screws (S07) unscrewed from the geared stepper motors.

connect_main_electronic_box_1

connect_main_electronic_box_2

connect_main_electronic_box_3

The C14 connector/terminal (E14) and the emergency stop switch (E17) were inserted into the holes on the front plate of the large electronic box.

connect_main_electronic_box_4

connect_main_electronic_box_5

connect_main_electronic_box_6

A small brown/red wire (E06) was cut out and the ends were stripped and twisted. Two 4.8 mm spade connectors (E26) were then attached to the stripped wire using a plier. The space connectors were connected between 10 and 1A on the back side of the C14 connector.

connect_main_electronic_box_7

connect_main_electronic_box_8

connect_main_electronic_box_9

connect_main_electronic_box_10

A longer brown wire was cut out to reach between L on the C14 connector and 13 on the emergency stop switch. The ends were stripped and twisted. A 4.8 mm spade connector (E26) was attached to the side connected to the C14 connector and a 6.3 mm space connector (E27) was attached to the side connected to the emergency stop switch. The spade connectors were then connected.

connect_main_electronic_box_11

connect_main_electronic_box_12

connect_main_electronic_box_13

Two short and one longer blue wire were cut out at an appropriate length and the ends of the wires were stripped and twisted.

connect_main_electronic_box_14

Two 4.8 mm spade connector (E26) were attached to one of the sides of each shorter wire and the other sides were inserted and locked into 1x 3-way Wago 221-413 (E07).

connect_main_electronic_box_15

connect_main_electronic_box_16

A 6.3 mm space connector (E27) was attached to one side of the longer blue wire and the other side were inserted and locked into the 3-way Wago 221-413 (E07).

I didn't have access to matching colors of all the spade connectors, so I followed the appropriate color scheme of the wires instead. So please ignore if there's a mismatch between the wire color and the spade connector color in the upcoming images.

connect_main_electronic_box_17

The shorter blue wires were connected to N and XX on the C14 connector. The longer blue wire was connected to 23 on the emergency stop switch.

connect_main_electronic_box_18

connect_main_electronic_box_19

One brown and one blue wire were cut out to reach between the emergency stop switch and the power supply's input terminals. The ends of the wires were stripped and twisted. Two 6.3 mm space connectors (E27) were attached to one side of the wires and 2x M4 ring terminals (E24) were attached to the other side. The blue wire's spade connector was connected to 24 on the emergency stop switch. The brown wire's spade connector was connected to 14 on the emergency stop switch.

connect_main_electronic_box_20

connect_main_electronic_box_21

connect_main_electronic_box_22

A small green/yellow wire was cut out to reach between the C14 connector and the power supply's input terminals. The end of the wire was stripped and twisted, a 4.8 mm spade connector (E26) was attached to one side and 1x M4 ring terminal (E24) was attached to the other side. The spade connector was then attached to ⏚ (ground) on the C14 connector.

connect_main_electronic_box_23

connect_main_electronic_box_24

The three M4 ring terminals were then connected to the power supply's input terminals in the following way:

  • Brown -> AC/L
  • Blue -> AC/N
  • Green/Yellow -> ⏚ (ground)

connect_main_electronic_box_25

connect_main_electronic_box_26

Power was connected to the C14 connector (read this note before connecting the power) and a multimeter was used to verify that the power supply outputted 12V. The multimeter was also used to verify that the C14 connector worked properly (cut power when using the switch) and that the emergency stop switch worked propertly (cut power when pushed. Also that the emegency stop switch remains off when C14 connector is switched off and on again).

connect_main_electronic_box_26

The emergency stop switch was attached to the front plate using 2x 18mm M4 screws (S09), 2x M4 nuts (N01) and two (9 mm, 4.5 mm, 1 mm) washers (W07).

connect_main_electronic_box_27

connect_main_electronic_box_28

The C14 connector was attached to the front plate using super glue. A cloth was used to remove excess glue.

connect_main_electronic_box_28_1

connect_main_electronic_box_28_2

connect_main_electronic_box_28_3

Shrink tubes (O24) were cut out at an appropriate length, one for each spade connector. Each spade connector was then temporarily removed and inserted into its shrink tube, before attached back again. The shrink tubes were then shrunk around all the spade connectors.

connect_main_electronic_box_29

connect_main_electronic_box_30

connect_main_electronic_box_31

connect_main_electronic_box_32

Prepare power to steppers and connect fans and LED

To prepare the power for the stepper motors, one black and one red wire (E03) were cut out (approx. 300 mm long) to reach between the 12V terminals on the power supply and the small electronic box containing the Arduino and CNC shield. One side of each wire was then stripped and twisted, and 2x M3 ring terminals (E23) were attached.

The red wire was connected to the V+ and the black wire was connected to V-.

connect_main_electronic_box_33

connect_main_electronic_box_34

connect_main_electronic_box_35

A 40x40 mm 12V fan (E01) was attached to the back side of the large electronic box's front panel, using 4x 12 mm M3 screws (S02). The fan was attached to blow air out of the box.

attach_fans_led_1

attach_fans_led_2

attach_fans_led_3

A 12V red LED (E22) was inserted into the small ďż˝~8 mm hole on the front of the large electronic box's front panel.

attach_fans_led_4

attach_fans_led_5

attach_fans_led_6

The second 40x40 mm 12V fan (E01) was attached to the back side of the small electronic box's front panel, using 4x 12 mm M3 screws (S02). A short flexible conduit (O13) reaching between the two eletronic boxes was cut out and the wires from the fan were inserted through it.

attach_fans_led_7

attach_fans_led_8

attach_fans_led_9

attach_fans_led_9

The loose wires of the two fans and the LED were stripped and twisted together, black together and red together. Then all three black wires were attached into the same M3 ring terminal (E23) and all three red wires were attached into the same M3 ring terminal (E23).

attach_fans_led_10

attach_fans_led_11

attach_fans_led_11

The red wires (red ring terminal) were finally connected to the V+ and the black wires (blue ring terminal) were connected to V- on the 12V power supply.

attach_fans_led_13

The red and black 12V power wires intended for the stepper motors were inserted through the same short flexible conduit as the fan wires.

attach_fans_led_14

2x 3d-printed strain relief halves (P11) were inserted into the hole on the side of the large electronic box facing the small electronic box. The large box was then carefully closed and attached to the upper and lower frame again. It's really important that you don't have to force it closed. If that's the case you need to move some cables for it to close smoothly.

attach_fans_led_15

attach_fans_led_16

attach_fans_led_17

attach_fans_led_18

Assemble stepper motor drivers and tune VRef

One small heatsink was attached to each DRV8825 stepper driver (E16).

vref_stepper_drivers_1

vref_stepper_drivers_2

Before the stepper motors were connected to the CNC shield, the stepper motor drivers' VRef needed to be tuned. The VRef regulates the voltage from the stepper driver to the stepper motor. If the VRefs are set to high, it can damage the stepper motors by supplying to much voltage.

The CNC shield (E10) was first attached to the Arduino Uno (E09).

vref_stepper_drivers_3

vref_stepper_drivers_4

The four stepper drivers were then attached to the CNC shield, one for each axis (X, Y, Z) and one for the mirrored Y-axis (A). The stepper drivers were inserted so that the "EN" pins on the stepper drivers aligned with the EN female terminal on the CNC shield.

vref_stepper_drivers_5

vref_stepper_drivers_6

vref_stepper_drivers_7

A USB cable (E28) was connected to the Arduino Uno and to a computer to supply the Arduino with power.

The power wires connected to the 12v power supply were connected to the CNC shield:

  • Red cable -> +
  • Black cable -> -

Power was then added to the system by inserting the C13 cable (E30) into the C14 connector on the front panel of the large electronic box.

vref_stepper_drivers_8

A multimeter was then used to regulate the VRef on each stepper driver. The equation to calculate the VRef differs depending on the stepper driver. The DRV8825 stepper drivers are using the following equation:

vref_stepper_drivers_8_1

By checking the I_{max} in the technical specification for each stepper motor, the following VRefs were calculated for each stepper driver:

Stepper driver I_{max} VRef
X 1.68A 1.68/2 = 0.84V
Y 1.68A 1.68/2 = 0.84V
A (mirrored Y) 1.68A 1.68/2 = 0.84V
Z 1.68A 1.68/2 = 0.84V

To measure the VRef of each stepper driver, the red test probe was connected to the screw on top of the stepper driver, and the black test probe was connected to the second bottom left pin (GND). The screw was then rotated to adjust the VRef to the appropriate voltage (~0.84V).

vref_stepper_drivers_9

vref_stepper_drivers_10

Attach Arduino and solder USB cable

The CNC shield was removed from the Arduino and the Arduino was attached to the back plate of the small electronic box using the 4x 5mm M3 screws (S07) unscrewed from the geared stepper motors. The USB cable was left inserted in the Arduino, as there was no space to insert it afterwards.

arduino_and_usb_1

arduino_and_usb_2

arduino_and_usb_3

The end of the USB cable was cut and stripped, showing the following 4 wires inside:

Color Type
Red VCC (+5V)
White Data -
Green Data +
Black GND

Each wire was stripped and twisted.

arduino_and_usb_3_1

A female USB-A (E29) was inserted into the front plate of the small electronic box. By using a soldering iron, solder/filler metal was first added to each pin on the female USB-A before attaching the wires, to simplify the soldering.

arduino_and_usb_4

arduino_and_usb_4

4 small shrink tubes (O24) were cut out and the wires were inserted into the shrink tubes.

arduino_and_usb_7

arduino_and_usb_8

To know which wire to solder to which pin, the following schema was used. The schema illustrates when looking straight into the female USB-A, with the flat surface at the top and the internal USB pins pointing downwards. As the pins goes straight through the connector, it's possible to map it to the pins on the back.

arduino_and_usb_6_1

arduino_and_usb_6

When the correct pin-wire-mapping was found, the wires were soldered one by one, by placing the stripped wires on the pins and then pressing the solder iron onto the tip of the wires. As filler metal had already been applied to the pins, no extra filler metal had to be added. The shrink tubes were then shrunk around the wires.

arduino_and_usb_9

arduino_and_usb_10

Finally, a 3d-printed block (P33) was glued to the female USB-A connector and the back of the front panel to lock it into place.

arduino_and_usb_11

arduino_and_usb_12

arduino_and_usb_13

arduino_and_usb_14

Stepper and end-stop cable management to small electronic box

The CNC shield was attached to the Arduino and 6x 3d-printed strain relief halves (P11) were inserted into the holes on the sides of the small electronic box.

steppers_to_cnc_shield_1

steppers_to_cnc_shield_2

Two flexible conduits (O13) were cut out to reach between the end of the Y-axis cable chain and the two holes in the small box. A hole was then drilled in the upper flexible conduit for the Y-axis end-stop wires to enter. To do this, the upper flexible conduit was placed where it was intended to be and tape was used to indicate the position of the hole.

A drill was then used to create the hole in the upper flexible conduit.

steppers_to_cnc_shield_3

steppers_to_cnc_shield_4

steppers_to_cnc_shield_5

steppers_to_cnc_shield_6

The Y-axis end-stop (+ and -) wires were inserted into the hole, followed by half of the wires coming from the Y-axis cable chain. The rest of the wires were inserted into the lower flexible conduit.

To simplify the process, the cables going into the same conduit were taped together.

steppers_to_cnc_shield_7

steppers_to_cnc_shield_8

steppers_to_cnc_shield_9

The end of the conduits were then placed between the strain relief halves and the front-middle part of the box were carefully attached to the frame again, locking the strain reliefs and the flexible conduits in place.

steppers_to_cnc_shield_10

steppers_to_cnc_shield_11

Connect steppers to CNC shield

To keep a good structure of the wires inside the small box, electrical crimp sleeves (E15) and contact housings (E13) were used. This also reduced the risks of shortings and loose wires.

steppers_to_cnc_shield_13

steppers_to_cnc_shield_18

For each stepper, the wires were cut at an appropriate length to reach to its connection on the CNC shield. Each wire were stripped and twisted. An AWG22/24 crimp connector was then attached to the end of each wire using a crimping tool. A shrinking tube (O24) was shrunk around the wires to keep a good structure.

The wires were then inserted and locked into a 1X4 contact housing (E13). Make sure to insert the wires in the correct orinentation, as the crimp connector has a "lock" that interlocks with the contact housing.

To know in which order to insert the wires, check the technical specification of your steppers. You should find something like this (given that you've bought bi-polar stepper motors):

A+ A- B+ B-
Black Green Red Blue

A and B indicate the two different coils in the stepper motor and the colors are the colors of the wires. You want to connect the crimp connectors so that each coil's wires are next to each other: A A B B.

steppers_to_cnc_shield_12

steppers_to_cnc_shield_14

steppers_to_cnc_shield_15

steppers_to_cnc_shield_16

steppers_to_cnc_shield_17

steppers_to_cnc_shield_19

This was done for all four steppers (X, Y, Z, A (mirrored Y)). Tape and a sharpie was used to indicate which contact housing beloning to which stepper. The contact housings were then connected to its connections on the CNC shield.

Note that if any of the steppers are moving in the "wrong" direction later on, you can just turn the connection 180 degrees and it will move the opposite way.

steppers_to_cnc_shield_20

steppers_to_cnc_shield_21

Finally, two jumpers (E19) were attached to the blue and yellow column on the "Y row". This tells the Arduino to mirror the Y-stepper instructions to the stepper connected to the A connection.

steppers_to_cnc_shield_22

steppers_to_cnc_shield_23

Connect end-stops to CNC shield

As with the stepper motor wires, electrical crimp connectors were used to keep a good structure in the small electornic box.

For each end-stop, the two wires were cut at an appropriate length to reach to its connection on the CNC shield. Each wire were stripped and twisted. An AWG22/24 crimp connector (E15) was then attached to the end of each wire using a crimping tool.

endstops_to_cnc_shield_1

endstops_to_cnc_shield_2

As I didn't have access to any 1x2 contact housings (E12), a shrinking tube (O24) was shrunk around each crimp connectors to reduce the risk of shorts.

This was done for all end-stops (X+, X-, Y+, Y- and Z+). Tape and a sharpie was used to indicate which pair of wires beloning to which end-stop. The crimp connector pairs were then connected to its connections on the CNC shield.

endstops_to_cnc_shield_3

endstops_to_cnc_shield_4

endstops_to_cnc_shield_5

endstops_to_cnc_shield_6

Set microstepping

Microstepping is a way to control the stepper motors in a smoother way and at a higher resolution, but usually at a lower speed and torque.

The 6 pins (M0, M1, M2) underneath each stepper driver were used to set the microstepping for each motor. By shorting the pins in certain combinations, different type of microstepping can be achieved (0 indicates no shorting, 1 indicates shorting):

Microstepping M0 M1 M2
Full-step 0 0 0
1/2 1 0 0
1/4 0 1 0
1/8 1 1 0
1/16 0 0 1
1/32 1 0 1

The 4 stepper drivers were carefully removed. The microstepping was set to 1/16 for each motor by shorting the two M2 pins using jumpers (E19). The stepper drivers were then carefully inserted back again.

set_microstepping_1

set_microstepping_2

Router cable management and connect to main power supply

NOTE: THIS PART INCLUDES WIRING OF HIGH VOLTAGE ELECTRICITY THAT CAN BE LETHAL IF NOT DONE PROPERLY. THE COLORS OF THE CABLES CAN VARY DEPENDING ON REGION/COUNTRY AND YOUR COMPONENTS/PINOUT NUMBERS MIGHT LOOK DIFFERENT. BEFORE YOU CONNECT THE POWER CORD TO THE POWER OUTLET, YOU MUST CONSULT WITH A LICENSED ELECTRICIAN TO MAKE SURE THAT EVERYTHING IS PROPERLY WIRED AND THAT IT IS IN LINE WITH YOUR LOCAL LEGISLATIONS.

As I wanted the emergency stop switch to kill the router as well, the router cable was inserted into the small electronic box to reach the emergency stop switch in the large electronic box.

A round cable grommet (O25) was inserted in the left side of the small electronic box, aligned between the two main wire holes.

The center of the hole was measured and drilled using a 8.5 mm drill. The cable grommet was then inserted and super glue was used to keep it in place.

router_small_box_1

router_small_box_2

router_small_box_3

router_small_box_4

router_small_box_5

The router cable was then inserted into the cable grommet. Some ordinary soap was used to reduce the friction between the rubber cable grommet and the rubber cable.

A cable tie (O11) was closed around the router cable on the inside of the box as a strain relief.

router_small_box_6

router_small_box_7

router_small_box_6_1

The large electronic box was opened once more and the router cable was inserted through the flexible conduit into the large electronic box. A cable clip (O10) was then used to position the router cable inside the small box.

The small electronic box was then carefully closed. It's really important that you don't have to force it closed. If that's the case you need to move some cables for it to close smoothly.

router_small_box_8

router_small_box_9

router_small_box_10

router_small_box_11

The blue and brown wires going between the emergency stop switch and the 12V power supply were cut in the middle and stripped and twisted. The router cable and the wires inside were also stripped and twisted.

router_small_box_12

router_small_box_14

router_small_box_15

router_small_box_13

The three brown wires were inserted and locked into a 3-way Wago 221-413 (E07). The three blue wires were also inserted and locked into a 3-way Wago 221-413 (E07).

The large electronic box was then carefully closed once more. It's really important that you don't have to force it closed. If that's the case you need to move some cables for it to close smoothly.

router_small_box_16

router_small_box_17

router_small_box_18

Final test of electrical wiring

The electrical wiring was tested by plugging in a C13 cable (E30) into the C14 socket and the C14 switch and emergency stop switch were turned on. But before this was done, I made sure that the router was turned off.

The red LED should light up, both fans should rotate and the router should rotate when turned on.

test_electrical_wiring_1

test_electrical_wiring_2

test_electrical_wiring_3

test_electrical_wiring_4

test_electrical_wiring_5

Wasteboard

Cut out wasteboard

The length and width of the CNC was measured and a 12 mm plywood (O26) was cut out using a vertical panel saw. If you don't have a vertical panel saw, a jigsaw or a circular saw works as well.

wasteboard_1

wasteboard_2

wasteboard_3

Attach wasteboard to CNC

The wasteboard was placed underneath the CNC machine. 7x 3d-printed wasteboard brackets (P37), 14x 3.5x20mm screws (S01) and 14x (15mm x 5mm x 1mm) washers (W02) were used to to keep the wasteboard in place.

wasteboard_4

wasteboard_5

wasteboard_7

wasteboard_6

wasteboard_8

wasteboard_9

Dust shoe (updated Feb 4, 2022)

The purpose of a dust shoe is to collect the dust generated by the CNC machine. Ivan's original dust shoe didn't fit my router, thus I designed a new dust shoe using a brush.

To not have to reprint the router bracket, I manually cut of the blocking piece from it. The STL/OBJ router bracket file in this repo is redesigned and updated, so no manual cutting should be needed.

The brush slot at the bottom of the vaccum funnel (P34) was measured and the brush (O27) was cut at an appropriate length. The brush was then inserted into the slot. As the fit was very tight, no glue was needed.

dust_shoe_1

dust_shoe_2

dust_shoe_3

dust_shoe_4

The vaccum funnel (P34) was placed next to the router bracket (P24) and a pen was used to indicate how much of the router bracket that was to be removed.

dust_shoe_5

dust_shoe_6

A hand-held Fein multitool was used to remove the blocking piece from the router bracket. A sand paper was used to smooth out the edges.

dust_shoe_7

dust_shoe_8

dust_shoe_9

dust_shoe_10

The vaccum funnel was then attached to the router bracket and a scissor was used to cut the brush at an appropriate length.

dust_shoe_11

1x 80 mm M5 screw (S17) and 1x M5 nut (N02) was used to lock the vaccum funnel in place.

dust_shoe_14

dust_shoe_15

dust_shoe_16

Software

Install CNC software (grbl) on Arduino Uno

The software used in this project to control the CNC machine is called grbl. It's an open source and high performance g-code-parser and CNC milling controller that can run on a straight Arduino Uno. To be able to install the software on the Arduino, an external computer was needed.

Install Arduino Software (IDE)

To be able to install grbl on the Arduino, Arduino Software (IDE) was installed on the computer. This program is used to upload code to the Arduino. The program was downloaded from Arduino's official website and the instructions were followed:

https://www.arduino.cc/en/software

After starting the program, you should see something like this:

install_software_1

Install GRBL

After installing the Arduino Software, the latest stable version of grbl was downloaded (as zip-format) from their official GitHub release page:

https://github.com/gnea/grbl/releases

After unzipping the file, you should see something similar to this in the folder:

install_software_2

Before grbl was loaded into the Arduino Software (IDE), a minor adjustment had to be done to grbl's config file, config.h. The reason for this was because when gbrl released v1.1, it changed the pin used by the Z end-stops. If this wasn't done, the Z end-stops wouldn't be recognized by grbl. To tell grbl that the old way of accessing the Z end-stops should be used, a specific variable in the config.h was commented out.

The config grbl/config.h was opened in a text editor and the line were the variable VARIABLE_SPINDLE is set was commented out by adding two slashes (//) at the beginning of the line (see the last line):

// Enables variable spindle output voltage for different RPM values. On the Arduino Uno, the spindle
// enable pin will output 5V for maximum RPM with 256 intermediate levels and 0V when disabled.
// NOTE: IMPORTANT for Arduino Unos! When enabled, the Z-limit pin D11 and spindle enable pin D12 switch!
// The hardware PWM output on pin D11 is required for variable spindle output voltages.
// #define VARIABLE_SPINDLE // <-- THIS SHOULD BE COMMENTED OUT!!

The updated config.h was saved.

The Arduino Software (IDE) was then launched and the Sketch > Include Library > Add .ZIP Library... menu alternative was clicked:

install_software_3

You should see a pop-up similar to this:

install_software_4

The unzipped grbl directory was opened and the folder grbl was chosen. After choosing the folder, a text below the editor appeared stating Library added to your libraries. Check "Include library" menu.

A USB cable was connected to the USB connection on the small electronic box.

Next, connect the Arduino to your computer.

install_software_5

To let the IDE know where to upload the software, the correct serial port and board were chosen. The serial port was set under Tools > Port > SOMETHINGSOMETHING (Arduino Uno).

If you have trouble finding the correct port, you might need to install 
CH340 drivers. It might occurr if you're using an Arduino clone. Look at
this resource for more info: 
https://learn.sparkfun.com/tutorials/how-to-install-ch340-drivers/all

install_software_8

The board was set under Tools > Board > Arduino Uno.

install_software_8_1

To test if the correct board and serial port were chosen, the template code (default code available when launching the IDE) was compiled by clicking on the check mark in the top left corner. When the compiling was done, the right-pointing arrow was clicked to upload the code to the Arduino. If successfull, you should see a text saying Done uploading below the editor.

install_software_9

install_software_10

The IDE was now ready to upload grbl to the Arduino. This was done by clicking File > Open in the top menu:

install_software_11

In the pop-up window, the downloaded folder was found and the following file grbl/examples/grblUpload/grblUpload.ino was opened.

install_software_12

A new pop-up was opened and the grbl code was compile by clicking on the check mark. When done, the compiled code was uploaded to the Arduino by clicking on the right-pointing arrow. grbl was now installed on the Arduino!

install_software_13

G-Code sender

To be able to send G-Code instructions from the computer to grbl on the Arduino, a G-Code sender is needed. grbl's official list of recommended G-Code senders can be found here: https://github.com/gnea/grbl/wiki/Using-Grbl (Sep 26, 2021)

Install G-Code sender

In this project a G-code sender called Universal G-Code Sender (UGS) was used. The program was downloaded from UGS's official website and the instructions were followed:

https://winder.github.io/ugs_website/download/

After starting the program, you should see something like this:

gcode_sender_1

Connect G-Code sender to GRBL

To let UGS know where to connect to, the correct firmware (GRBL) and serial port (cu.usbmodem<NUMBER>) were chosen. If you can't find the correct serial port, click the spinning arrows to refresh the ports.

gcode_sender_2

gcode_sender_3

UGS was then connected to the Arduino by clicking on plug/socket icon in the top left corner. If the connection succeeds, you should see the plug/socket icon turn orange and the GRBL configuration outputted in the console.

gcode_sender_4

gcode_sender_5

Adjust GRBL configuration

The GRBL configuration enables you to adjust important settings, such as the maximum mm/min rates for different axes and if the end-stops should be used. A full description of all settings can be found here:

https://github.com/gnea/grbl/blob/master/doc/markdown/settings.md (Sep 26, 2021)

To update a setting, the new setting is inputted into the console command line, e.g.: $21 = 1 to enable end-stops/hard limits. A confirmation that the setting is changed is then outputted in the console.

gcode_sender_6

Enable end-stops/hard limits

The end-stops/hard limits were enabled by updating the following setting:

$21 = 0 -> $21 = 1

To test that the end-stops were working properly, each end-stop was tested by manually triggering it with a finger. After triggering, an alarm should be raised in UGS.

gcode_sender_7

gcode_sender_8

After the alarm was triggered, UGS was reset by clicking Soft reset and Unlock.

gcode_sender_9

Calculate and set travel resolutions

The most important settings to adjust is the X-axis, Y-axis and Z-axis travel resolutions. These settings tells GRBL how many steps it should take to move one millimeter. The travel resolution depends on the stepper motor's steps per revolution, the microstepping, the teeth spacing and the number of teeth on the timing pulley(s).

The following equation was used to calculate the travel resolution (steps/mm) for each stepper:

gcode_sender_10

In this project, this is how the travel resolutions were calculated:

Stepper motor Microstepping Step angle Steps per revolution Teeth spacing Number of teeth - Pulley 1 Number of teeth - Pulley 2 Travel resolution
X-axis 16 0.094 deg 360/0.094 = 3829.7872 steps 5 mm (HTD5M) 12 1 (used when no pulley 2) (16*3829.7872)/(5*12/1) = 1021.277
Y-axis (1) 16 0.094 deg 360/0.094 = 3829.7872 steps 5 mm (HTD5M) 12 1 (used when no pulley 2) (16*3829.7872)/(5*12/1) = 1021.277
Y-axis (2) 16 0.094 deg 360/0.094 = 3829.7872 steps 5 mm (HTD5M) 12 1 (used when no pulley 2) (16*3829.7872)/(5*12/1) = 1021.277
Z-axis 16 1.8 deg 360/1.8 = 200 steps 8 mm (acme rod) 16 60 (16*200)/(8*16/60) = 1500

The travel resolutions were updated:

  • X-axis travel resolution: $100=250.000 -> $100 = 1021.277
  • Y-axis travel resolution: $101=250.000 -> $101 = 1021.277
  • Z-axis travel resolution: $102=250.000 -> $102 = 1500.000

The calculated travel resolutions were validated by moving each axis 10 mm in UGS and measuring the actual distance moved.

gcode_sender_11

gcode_sender_12

gcode_sender_13

Other configurations

The homing cycle is when the CNC machine automatically moves all axises to it's limits to home itself before starting the job. I disabled this as I will manually jog the router to it's position:

$22 = 1 -> $22 = 0

The X-axis and Y-axis minimum rates were increased to 1000:

  • X-axis maximum rate: $110=500.000 -> $110 = 1000.000
  • Y-axis maximum rate: $111=500.000 -> $111 = 1000.000

The X-axis and Y-axis maximum travel were increased to 500:

  • X-axis maximum travel: $130=200.000 -> $130 = 500.000
  • Y-axis maximum travel: $131=200.000 -> $131 = 500.000

Final notes

I have a couple of things I want to improve with this build:

  • Build a wasteboard using wasteboard clamps
  • Design a dust shoe

cnc_top_gif

Releases

No releases published

Packages

No packages published