Get duckyPad | Official Discord | Getting Started | Table of Contents
Thanks for purchasing duckyPad! Here is a short guide on how to put everything together.
Feel free to join our Official Discord for discussions, asking questions, sharing scripts, and latest updates!
A small Phillips-head screwdriver (+shape) is needed, there should be one provided in the package.
A pair of pliers would make tightening the fasteners easier, but by no means required. You can use your hand just fine.
When handling the bare circuit board, remember to:
-
Wash your hands first
-
Always hold the circuit board by its edge
-
Don't touch the components
The reason for hand-washing is to reduce the risk of static electricity(SE) on your body zapping the board and damage it, especially in dry weather.
By washing your hands, you release the existing SE through the metal water pipe, your hands are moist to prevent further SE build-up, and your clean hands won't leave greasy fingerprints all over the place, win-win-win!
Of course, your hands can't be dripping wet either, but that's just common sense.
By now, you should have:
-
1x duckyPad circuit board
-
1x Front Plate
-
1x Back Plate
-
15x Cherry MX-style switches
-
15x Keycaps
-
4x Silicone Anti-slip Pad
-
Fasteners
-
microSD Card
You should have the following fasteners:
-
6x
8mm Screw -
8x
2.8mm Screw -
7x
2mm Standoff -
6x
4mm Standoff
Be careful while handling them, if you drop one you'll never find it again!
Probably safer to leave them in the bag for now.
Start by peeling off the protective cover on the front and back plate:
Place the Back Plate in front of you like this. Note the orientation of the holes:
Start from a hole in the middle, put a 8mm Screw through the back side:
Then screw on the 2mm Standoff.
Don't over-tighten! Doing so might deform or crack the acrylic plate.
Finger-tight is OK, just make sure it's not loose and doesn't rattle.
Do the same with all the holes EXCEPT the bottom right:
Put a 2.8mm Screw through that one:
And install the 2mm Standoff.
This is gonna be a PITA, but you'll eventually get it :) Careful not to drop the small parts.
Now go wash your hands, grab the circuit board by its edge, line up and install as shown:
Then install all 6 4mm Standoffs, moderately tighten.
Also install the 2.8mm Screw on the lower right.
Line up the Front Plate, and install the 2.8mm Screws.
DO NOT tighten each screw as you install it! Put them all on loosely first, then tighten them one-by-one.
This ensures the plate is properly lined up. Again, don't over-tighten.
Flip it over, clean the plate with a dry cloth if dirty, and stick on the anti-slip pads on each corner:
Time to install the switches! duckyPad supports hot-swap, so no soldering is needed.
-
Make sure the pins are straight!
-
Make sure the pins are straight!
-
Make sure the pins are straight!, otherwise you might damage the circuit board or the switch itself!
Then line up with the holes, and gently push straight down until it clicks in place:
Keycaps next! Note the orientation ("slope" side pointing left in this photo). Just push it down.
All the keys should be lined up evenly. If not, try push down or wiggle it a little.
Finally, if it hasn't already been done, peel off the protective cover on the OLED screen:
And you're done! Congratulations!
Head on down to the Quick Start Guide to see how to use it.
Using duckyScript | duckyScript 3 Info
Common issues / Troubleshooting
Firmware Updates and Version History
Kickstarter Backer Acknowledgments
Please feel free to open an issue, ask in the official duckyPad discord, DM me on discord dekuNukem#6998, or email dekuNukem@gmail.com for inquires.