SMM2-Printer

中文说明

Using LUFA to emulate Nintendo Switch's controller input, automatic draw images in comment of Super Mario Maker 2.

Printing Comments

This works by using the smallest size pen and D-pad inputs to plot out each pixel one-by-one.

Printing Procedure

Just press L to select the pixel pen and plug in the controller: it will automatically sync with the console, reset the cursor position, clean the canvas and print. In case you see issues with controller conflicts while in docked mode, try using a USB-C to USB-A adapter in handheld mode. In dock mode, changes in the HDMI connection will briefly make the Switch not respond to incoming USB commands, skipping pixels in the printout. These changes may include turning off the TV, or switching the HDMI input. (Switching to the internal tuner will be OK, if this doesn't trigger a change in the HDMI input.)

The printing goes from top to bottom, alternating between two lines, from left to right and viceversa. Printing times varies from 30 minutes to 4 hours depending on image preprocessing methods.

Optionally, upon completion, the Teensy's LED will begin flashing. On compatible Arduino boards, some combination of the onboard LEDs will flash. On the UNO, for instance, both TX and RX LEDs will flash, however the other LEDs will not. If this functionality is desired, issue make with-alert when building the firmware. All pins on both PORTB and PORTD are toggled! Beware of possible interactions with any attached peripherals, say from another project.

This repository has been tested using a Teensy 2.0++.

Compiling and Flashing onto the Teensy 2.0++

Go to the Teensy website and download/install the Teensy Loader application. For Linux, follow their instructions for installing the GCC Compiler and Tools. For Windows, you will need the latest AVR toolchain from the Atmel site. (Note for Mac users - the AVR MacPack is now called AVR CrossPack. If that does not work, you can try installing avr-gcc with brew.)

Next, you need to grab the LUFA library. You can download it in a zipped folder at the bottom of this page. Unzip the folder, rename it LUFA, and place it where you like. Then, download or clone the contents of this repository onto your computer. Next, you'll need to make sure the LUFA_PATH inside of the makefile points to the LUFA subdirectory inside your LUFA directory. My Switch-Fightstick directory is in the same directory as my LUFA directory, so I set LUFA_PATH = ../LUFA/LUFA.

Now you should be ready to rock. Open a terminal window in the Switch-Fightstick directory, type make, and hit enter to compile. If all goes well, the printout in the terminal will let you know it finished the build! Follow the directions on flashing Joystick.hex onto your Teensy, which can be found page where you downloaded the Teensy Loader application.

Compiling and Flashing onto the Arduino UNO R3

You will need to set your Arduino in DFU mode, and flash its USB controller. (Note for Mac users - try brew to install the dfu-programmer with brew install dfu-programmer.) Setting an Arduino UNO R3 in DFU mode is quite easy, all you need is a jumper (the boards come with the needed pins in place). Please note that once the board is flashed, you will need to flash it back with the original firmware to make it work again as a standard Arduino. To compile this project you will need the AVR GCC Compiler and Tools. (Again for Mac users - try brew, adding the osx-cross/avr repository, all you need to do is to type brew tap osx-cross/avr and brew install avr-gcc.) Next, you need to grab the LUFA library: download and install it following the steps described for the Teensy 2.0++.

Finally, open a terminal window in the Switch-Fightstick directory, edit the makefile setting MCU = atmega16u2, and compile by typing make. Follow the DFU mode directions to flash Joystick.hex onto your Arduino UNO R3 and you are done.

Compiling and Flashing onto the Arduino Micro

The Arduino Micro is more like the Teensy in that it has a single microcontroller that communicates directly over USB. Most of the steps are the same as those for the Teensy, except do not download Teensy Loader program. You will also need to edit makefile before issuing make. Change MCU = at90usb1286 on line 15 to MCU = atmega32u4.

Once finished building, start up Arduino IDE. Under File -> Preferences, check Show verbose output during: upload and pick OK. With the Arduino plugged in and properly selected under Tools, upload any sketch. Find the line with avrdude and copy the entire avrdude command and all options into a terminal, replacing the .hex file and path to the location of the Joystick.hex created in the previous step. Also make sure the -P/dev/?? port is the same as what Arduino IDE is currently reporting. Now double tap the reset button on the Arduino and quickly press Enter in the terminal. This may take several tries. You may need to press Enter first and then the reset button or try various timings. Eventually, avrdude should report success. Store the avrdude command in a text file or somewhere safe since you will need it every time you want to print a new image.

Sometimes, the Arduino will show up under a different port, so you may need to run Arduino IDE again to see the current port of your Micro.

If you ever need to use your Arduino Micro with Arduino IDE again, the process is somewhat similar. Upload your sketch in the usual way and double tap reset button on the Arduino. It may take several tries and various timings, but should eventually be successful.

The Arduino Leonardo is theoretically compatible, but has not been tested. It also has the ATmega32u4, and is layed out somewhat similar to the Micro.

Attaching the optional buzzer

A suitable 5V buzzer may be attached to any of the available pins on PORTB or PORTD. When compiled with make with-alert, it will begin sounding once printing has finished. See above warning about PORTB and PORTD. Reference section 31 of the AT90USB1286 datasheet for maximum current specs.

Pin 6 on the Teensy is already used for the LED and it draws around 3mA when fully lit. It is recommended to connect the buzzer to another pin. Do not bridge pins for more current.

For the Arduino UNO, the easiest place to connect the buzzer is to any pin of JP2, or pins 1, 3, or 4 of ICSP1, next to JP2. Refer to section 29 of the ATmega16u2 datasheet for maximum current specs. Do not bridge pins for more current.

On the Arduino Micro, D0-D3 may be used, or pins 1, 3, or 4 (PORTB) on the ICSP header. Power specs are the same as for the AT90USB1286 used on the Teensy. The TX and RX LEDs are on PORTD and PORTB respectively and draw around 3mA apiece. Do not bridge pins for more current.

Using your own image

The image printed depends on image.c which is generated with png2c.py which takes a 320x180 .png image. png2c.py will pack the image to a linear 5bpp array.

png2c.py support different processing method, examples are shown bellow:

Method	Result	Arguments	Description
Origin		None	Original image
Dither		None (Default)	The best way to restore origin image, drawing takes a long time. (Usually hours)
Average		-a	The restore effect is poor and the drawing time is shorter. Suitable for vector pictures / anime.
Monochrome		-m	The fasted way to draw, only three color was used.

In order to run png2c.py, you need to install Python (I use Python 2.7). Also, you need to have the Python Imaging Library installed (install pip if you need to). Using the supplied sample image, example.png:

$ python png2c.py example.png

Substitute your own .png image to generate the image.c file necessary to print. Just make sure your image is in the Switch-Fightstick directory.

To generate an monochrome of the image:

$ python png2c.py -m example.png

To preview output, simply add -p argument:

$ python png2c.py -p example.png