Version 2.3.0

• Allow reading raw frames or I/Q data from standard input. To enable this,
  specify "-" as the argument to --iq-file or --raw-frames-file option,
  respectively.
• Added --prettify-json command line option which enables prettification of
  JSON payloads in libacars >= 2.2.0. This currently applies to OHMA messages
  only.
• Fixed incompatibility with libacars 2.2.0 which might cause a crash during
  reassembly of CLNP packets.

Version 2.2.0

• Added support for reassembly of multipart CLNP and COTP packets. This brings
  the ability to decode ADS-C v2 messages which are too large to fit in a single
  CLNP / COTP packet, even if fragmented in the X.25 layer.
• Added proper formatting of Route Clearance CPDLC message elements.
• Removed the obsolete 8-channel limit. The maximum number of VDL2 channels that
  can be decoded simultaneously is now limited only by the hardware (thx
  @rpatel3001).
• Station ID (specified with --station-id option) is now appended to the StatsD
  namespace if StatsD metric collection is enabled. For example, if the station
  ID is set to KLAX, the new namespace would be "dumpvdl2.KLAX" instead of just
  "dumpvdl2". This allows simultaneous monitoring of several dumpvdl2 instances
  separately in Grafana (thx @cdschuett).
• Fixed a crash which occurred when the ground station list file could not be
  opened.

Version 2.1.1

• Fixed wrong ZeroMQ version check, which incorrectly declared ZMQ version 4.0.x as too old (#18)

Version 2.1.0

• Added full JSON formatting for all protocols and message types. This is
  supported on all output types - file, udp and zmq. Together with multiple
  outputs feature that was introduced in version 2.0.0 this enables arbitrarily
  flexible arrangements, like logging to a file as text, logging to another
  file as JSON and sending JSON across the network using UDP and/or ZMQ. When
  collecting data from multiple receivers, --station-id option may be used to
  assign unique names to receivers in order to discriminate input from each
  one.

• Removed a few duplicate routines that have their counterparts in libacars.

Version 2.0.1

• Fixed build failure with gcc version 10.

Version 2.0.0

• Major overhaul of the output subsystem. The new architecture is modular, multithreaded and can easily be extended with new output drivers. It also allows using multiple outputs simultaneously.
• New output configuration scheme. --output-file --daily, --hourly and --output-acars-pp options have been removed. All outputs are now configured using --output option. Adjusting command line parameters is therefore required to run the program. Run dumpvdl2 --output help for instructions or see "Output configuration" section in README.md for details and examples.
• Support for streaming messages over network using UDP/IP.
• Support for streaming messages over network using ZeroMQ publisher sockets. Requires libzmq library.
• Support for storing AVLC frames as raw data (without decoding) in binary files for archiving purposes. File contents can then be decoded anytime later, as if the frames were just received from the air. Requires protobuf-c library.
• Minor bugfixes.

Version 1.10.1

• Added support for SDRPlay API version 3 which is required for new devices (notably RSPdx). API version 2 is still supported, however it will probably be removed in a future release. It is possible to have both versions installed simultaneously and to choose which one to use at runtime. See README.md for details.
• Added --milliseconds option which enables printing timestamps in message headers up to a millisecond precision. Note that the arrival timestamp is stored per VDL2 burst, not per VDL2 message. Since a VDL2 burst may contains more than one VDL2 message, all messages extracted from a single burst will still have exactly the same timestamp value, regardless of whether millisecond precision has been enabled or not.

Version 1.9.0

• Added decoder for ISO 8650 / X.227 Association Control Service (ACSE).
• Improved decoder for ISO 8327 / X.225 Session Protocol.
• Restructured code of ATN applications decoder. The previous implementation
  was a little messy and was unable to handle a few uncommon types of messages
  (like ACSE Abort PDU with no payload). This should bring the number of
  undecoded ATN messages down to zero.
• Enable debugging output from SDRPlay driver only if --debug sdr option is used.
• Fix formatting of geo coordinates in ADS-C v2 messages.

Version 1.8.2

• Fix another crash opportunity due to missing sanity check on unparseable ACARS
  messages.
• Fix ACARS output to Planeplotter. Only first three characters of Message
  Serial Number (MSN) field were sent instead of all four.

Version 1.8.1

• Fix a bug where an unparseable ACARS message could cause the program to crash.
• Add a little bit of optimization when compiling with debugging enabled. Debug
  builds are now compiled with -Og flag rather than -O0. This makes debugging on
  a Raspberry Pi feasible - when -O0 was used, CPU usage was often too high and
  caused loss of samples and reduced decoding success rate.