Please use the system-supplied and supported gpio-shutdown boot overlay. This repo is obsolete

Combined Restart / Shutdown Button for Raspberry Pi

A very simple systemd service for Raspberry Pi that provides a software-controlled restart / shutdown button.

Use

Default behaviour is:

• your Raspberry Pi will reset if the button is held for more than two seconds but fewer than five seconds;

• your Raspberry Pi will shut down if the button is held for more than five seconds.

By default, the software assumes the switch is connected to pin BCM 27. Both the pin and the timing can be changed in the Python source file.

Requirements

Hardware

• A Raspberry Pi (tested on a model 2B, 3B and Zero, and on a model B after minor software modification)

• A normally open, momentary contact button. I use surplus ATX power buttons (as used on desktop PCs), as they're cheap and come with a handy set of wires and header connectors. Virtually any button will do the job, though. Just make sure it's normally open (push to close).

Software

• A Debian-based operating system that uses systemd (tested on Jessie and Stretch)

• the python3-gpiozero package to provide GPIO Zero (tested on version 1.4.0)

Installation

Hardware

40-pin GPIO connector (B+, 2B, 3B, Zero)

Connect the button between GPIO 27 and GND. If you use an ATX power button and a Raspberry Pi with a 40-pin GPIO header, connect it across the seventh column from the left:

            -
· · · · · ·|·|· · · · · · · · · · · · · 
· · · · · ·|·|· · · · · · · · · · · · · 
            -

This shorts GPIO 27 (physical pin 13) to ground (physical pin 14) when the button is pressed.

26-pin GPIO connector (models B and A only)

GPIO 27 is not exposed on the original Raspberry Pi header, so GPIO 17 is a reasonable option. If you use an ATX power button and a Raspberry Pi with a 26-pin GPIO header, connect it across the fifth and sixth columns of the second row:

. . . . ._. . . . . . . .
. . . .|. .|. . . . . . .
         -

You will also need to change line 7 of shutdown_button.py to read:

use_button=17

Software

The software is installed with the following commands:

sudo apt install python3-gpiozero
sudo mkdir -p /usr/local/bin
chmod +x shutdown_button.py
sudo cp shutdown_button.py /usr/local/bin
sudo cp shutdown_button.service /etc/systemd/system
sudo systemctl enable shutdown_button.service
sudo systemctl start shutdown_button.service

Troubleshooting

Enabling the service should produce output very similar to:

Created symlink /etc/systemd/system/multi-user.target.wants/shutdown_button.service → /etc/systemd/system/shutdown_button.service.

You can check the status of the program at any time with the command:

systemctl status shutdown_button.service

This should produce output similar to:

● shutdown_button.service - GPIO shutdown button
   Loaded: loaded (/etc/systemd/system/shutdown_button.service; enabled; vendor 
   Active: active (running) since Sat 2017-10-21 11:20:56 EDT; 27s ago
 Main PID: 3157 (python3)
   CGroup: /system.slice/shutdown_button.service
           └─3157 /usr/bin/python3 /usr/local/bin/shutdown_button.py

Oct 21 11:20:56 naan systemd[1]: Started GPIO shutdown button.

If you're seeing anything other than Active: active (running), it's not working. Does the Python script have the right permissions? Is it in the right place? If you modified the script, did you check it for syntax errors? If you're using a model A or B with a 26-pin GPIO connector, did you make the modifications in the Python script to use GPIO 17 instead of 27?

The output from dmesg will show you any error messages generated by the service.

Modifications

If you use a HAT/pHAT/Bonnet/etc. with your Raspberry Pi, check pinout.xyz to see if it uses BCM 27. If you do need to change the pin, best to pick one that doesn't have a useful system service like serial I/O or SPI. If you're using an ATX button with a two pin connector, make sure you choose a pin physically adjacent to a ground pin.

If you modify the timing, please ensure that you keep the shutdown button press duration longer than the reboot one. Otherwise you'll only be able to shut down.

Notes

You should not need to reboot to enable the service. One machine of mine — a Raspberry Pi Zero running Raspbian Stretch — did need a reboot before the button worked.

The reboot code is based on the Shutdown button example from the GPIO Zero documentation.

This is not the only combined shutdown/reset button project to use GPIO Zero. gilyes/pi-shutdown also does so, but pre-dates the implementation of the various hold time functions in GPIO Zero.

GPIO 27 was used, as it's broken out onto a physical button on the Adafruit PiTFT+ display I own.

This is my first systemd service, and I'm still at the “amazed it works at all” stage. The service file may not contain the ideal configuration.

Connector Pinouts

From GPIO Zero's pinout command

40 pin

   3V3  (1) (2)  5V    
 GPIO2  (3) (4)  5V    
 GPIO3  (5) (6)  GND   
 GPIO4  (7) (8)  GPIO14
   GND  (9) (10) GPIO15
GPIO17 (11) (12) GPIO18
GPIO27 (13) (14) GND   
GPIO22 (15) (16) GPIO23
   3V3 (17) (18) GPIO24
GPIO10 (19) (20) GND   
 GPIO9 (21) (22) GPIO25
GPIO11 (23) (24) GPIO8 
   GND (25) (26) GPIO7 
 GPIO0 (27) (28) GPIO1 
 GPIO5 (29) (30) GND   
 GPIO6 (31) (32) GPIO12
GPIO13 (33) (34) GND   
GPIO19 (35) (36) GPIO16
GPIO26 (37) (38) GPIO20
   GND (39) (40) GPIO21

26 pin

   3V3  (1) (2)  5V    
 GPIO0  (3) (4)  5V    
 GPIO1  (5) (6)  GND   
 GPIO4  (7) (8)  GPIO14
   GND  (9) (10) GPIO15
GPIO17 (11) (12) GPIO18
GPIO21 (13) (14) GND   
GPIO22 (15) (16) GPIO23
   3V3 (17) (18) GPIO24
GPIO10 (19) (20) GND   
 GPIO9 (21) (22) GPIO25
GPIO11 (23) (24) GPIO8 
   GND (25) (26) GPIO7 

Author

Stewart C. Russell — scruss.com — @scruss.

Writeup (with some pictures): http://scruss.com/blog/2017/10/21/combined-restart-shutdown-button-for-raspberry-pi/