Skip to content

Epoxy coffe table with 3d printed hexagon inserts and led pcbs with touch sensor

License

Notifications You must be signed in to change notification settings

mazls/hexagon-desk

Folders and files

NameName
Last commit message
Last commit date

Latest commit

 

History

42 Commits
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Repository files navigation

Hexagon Desk

Epoxy Coffe Table

This work is licensed under a Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License.

CC BY-NC-SA 4.0

Hexagon Desk

📖 Table of Contents

Table of Contents
  1. ➤ About The Project
  2. ➤ Overview
  3. ➤ Project Files Description
  4. ➤ Getting Started
  5. ➤ PCB: Main-PCB
  6. ➤ PCB: HexagonPCB
  7. ➤ Useful Links:
  8. ➤ Sponsor:

-----------------------------------------------------

📝 About The Project

I saw a short TikTok with a led table that lights up when touched and immediately felt like building it myself. So i designed my own Main-PCB and little hexagonal PCBs for the light and touch. Unfortunately, there were a few setbacks due to the availability of some components. So I had to equip the main PCB with self soldered components. I also had to get the touch sensors externally and solder them on. If the whole thing with the chips calms down a bit I will tackle the whole thing again and simplify it.

HexagonDesk

-----------------------------------------------------

☁️ Overview

This project still requires a lot of manual work. The main board still has to be assembled by yourself, as well as the touch sensors on the Hexagon boards. Also a lot of wiring has to be done. The touch sensors are individually connected to the main board. The WS2812B on the hexagons are looped through per channel.

I have created a bom and instructions. however, these are still far from good. I am always working on improving these and also on the programme/boards. I have opened the discussions area for questions, suggestions etc.

HexagonWiring

-----------------------------------------------------

💾 Project Files Description

  • Desk_PRG.ino - Is the first version with an ESP32 as main controller
  • Desk_PRG_RP2040.ino - Is the current version with a RP2040 as controller.
  • Adafruit_MCP23017.cpp/Adafruit_MCP23017.h - Is for the MCP23017 I2C communication
  • FastLED - This is a modified Version of FastLED V3.4 to work with the RP2040

-----------------------------------------------------

📖 Getting Started

Install the RP2040 Board: https://github.com/earlephilhower/arduino-pico

For ESP32 you have to install ESP32 Boards: https://randomnerdtutorials.com/installing-the-esp32-board-in-arduino-ide-windows-instructions/

For RP2040 You have to clone the repo and copy the FastLED folder in your "...\Dokuments\Arduino\libraries\" folder to work with the RP2040

Now you should be able to compile the

Desk_PRG_RP2040.ino

In the header you should config your Setup

Just configure the amount of Hexagon PCBs you have connectet to channel 0-3

#define Hexagons_channel_0  12
#define Hexagons_channel_1  12
#define Hexagons_channel_2  12
#define Hexagons_channel_3  14

In this config i have connectet 12 Hexagon PCBs to channel 0, 12 Hexagon PCBs to channel 1, 12 Hexagon PCBs to channel 2 and 14 Hexagon PCBs to channel 3. The desk was build with 50 Hexagon PCBs. The maximum is 64, but this can be expanded with more MCP23017.

-----------------------------------------------------

🔸 Main-PCB: What is the Main-PCB

The Main-PCB contains 4x MCP23017, 2x 1500uF Capacitor, 1x Fuse holder, 1x SN74HC125N and one ESP32 Dev Kit C / Raspberry Pi Pico

The MCP23017 are communicating over I2C, every MCP23017 has 16 Inputs/Outputs.

The SN74HC125N is to shift the data channel from 3.3V to 5V so the leds don't glitch.

-----------------------------------------------------

🔸 HexagonPCB: The LED and Touch PCBs

I have designed this PCB to integrate the LEDs and the Touch Sensor.

The PCB has a "Data IN" and "Data OUT" so it is possible to connect multiple PCBs to act as a WS2812B Strip

Every PCB has a "Signal" Pin which connects the signal output from the TTP223 PCB to the Main-PCB

The Input Voltage is 5V for the PCB

I have scraped some varnish from the touch surface of the TTP223 sensors and soldered a cable there, which then functions as a touch sensor.

HexagonPCB

-----------------------------------------------------

BOM

[Tisch_BOM.xlsx](https://github.com/mazls/hexagon-desk/blob/main/BOM/Tisch_BOM.xlsx)

Schematic Wiring

[Wiring.pdf](https://github.com/mazls/hexagon-desk/files/8800328/Wiring.pdf)

Desk Cutout for 50 Hexagons

[Hex_Desk_Ausschnitt.pdf](https://github.com/mazls/hexagon-desk/blob/main/Woodwork/Hex_Desk_Ausschnitt.pdf)

Desk Legs

[Table_legs.pdf](https://github.com/mazls/hexagon-desk/blob/main/Woodwork/Table_legs.pdf)

Print files can be found here:

https://www.printables.com/model/200964-hexagon-led-coffee-table

HexagonPrint

Dev Kit link:

https://www.az-delivery.de/en/products/esp32-developmentboard

Videos

https://youtu.be/I4rWym8PK4s

https://www.youtube.com/watch?v=-OrUfqWGYhM&feature=emb_title

-----------------------------------------------------

➤ Sponsor:

PCBway kindly sponsored a batch of PCBs which you can see pictures of inside the _img folder. The pcbs came in an absolutely outstanding quality and also very fast!

Ordering at PCBWay is simple:

Upload the files from the desired folder After submitting your file, a PCBWay engineer will spend a few minutes reviewing your file to make sure everything goes smoothly for production. For high-priority work, it's always good to see how things are progressing. You have the opportunity to check the production status of each step. For assembled PCB, PCBWay will also send you sample photos for preview and confirmation.

PCBwaylogo.png

http://pcbway.com

Releases

No releases published

Packages

No packages published

Languages