Skip to content

fjp/frenet

Folders and files

NameName
Last commit message
Last commit date

Latest commit

 

History

72 Commits
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Repository files navigation

Trajectory Planning in the Frenet Space

There are many ways to plan a trajectory for a robot. A trajectory can be seen as a set of time ordered state vectors $x$. The following algorithm introduces a way to plan trajectories to maneuver a mobile robot in a 2D plane. It is specifically useful for structured environments, like highways, where a rough path, referred to as reference, is available a priori.

Path planning in frenet coordinates:

Trajectory Planning using frenet coordinates.

Algorithm

  1. Determine the trajectory start state $[x_1,x_2,\theta,\kappa,v,a](0)$ The trajectory start state is obtained by evaluating the previously calculated trajectory at the prospective start state (low-level-stabilization). At system initialization and after reinitialization, the current vehicle position is used instead (high-level-stabilization).
  2. Selection of the lateral mode Depending on the velocity $v$ the time based ($d(t)$) or running length / arc length based ($d(s)$) lateral planning mode is activated. By projecting the start state onto the reference curve the the longitudinal start position $s(0)$ is determined. The frenet state vector $[s,\dot{s},\ddot{s},d,d',d''](0)$ can be determined using the frenet transformation. For the time based lateral planning mode, $[\dot{d}, \ddot{d}](0)$ need to be calculated.
  3. Generating the laterl and longitudinal trajectories Trajectories including their costs are generated for the lateral (mode dependent) as well as the longitudinal motion (velocity keeping, vehicle following / distance keeping) in the frenet space. In this stage, trajectories with high lateral accelerations with respect to the reference path can be neglected to improve the computational performance.
  4. Combining lateral and longitudinal trajectories Summing the partial costs of lateral and longitduinal costs using $J(d(t),s(t)) = J_d(d(t)) + k_s \cdot J_s(s(t))$, for all active longidtuinal mode every longitudinal trajectory is combined with every lateral trajectory and transfromed back to world coordinates using the reference path. The trajectories are verified if they obey physical driving limits by subsequent point wise evaluation of curvature and acceleration. This leads to a set of potentially drivable maneuvers of a specific mode in world coordinates.
  5. Static and dynamic collision check Every trajectory set is evaluated with increasing total costs if static and dynamic collisions are avoided. The trajectory with the lowest cost is then selected.
  6. Longitudinal mode alternation Using the sign based (in the beginning) jerk $\dot{a}(0)$, the trajectory with the strongest decceleration or the trajectory which accelerates the least respectively is selected and passed to the controller.

Frenet Coordinates

"Frenet Coordinates", are a way of representing position on a road in a more intuitive way than traditional (x,y) Cartesian Coordinates.

With Frenet coordinates, we use the variables s and d to describe a vehicle's position on the road or a reference path. The s coordinate represents distance along the road (also known as longitudinal displacement) and the d coordinate represents side-to-side position on the road (relative to the reference path), and is also known as lateral displacement.

In the following sections the advantages and disadvantages of Frenet coordinates are compared to the Cartesian coordinates.

Frenet Features

The image below depicts a curvy road with a Cartesian coordinate system laid on top of it, as well as a curved (continuously curved) reference path (for example the middle of the road).

Representation of a reference path (blue) in Cartesian coordinates (x,d).

The next image shows the same reference path together with its Frenet coordinates.

Representation of a reference path in Frenet coordinates (s,d) on a road segment.

The s coordinate represents the run length and starts with s = 0 at the beginning of the reference path. Lateral positions relative to the reference path are are represented with the d coordinate. Positions on the reference path are represented with d = 0. d is positive to the left of the reference path and negative on the right of it, although this depends on the convention used for the local reference frame.

The image above shows that curved reference paths (such as curvy roads) are represented as straight lines on the s axis in Frenet coordinates. However, motions that do not follow the reference path exactly result in non straight motions in Frenet coordinates. Instead such motions result in an offset from the reference path and therefore the s axis, which is described with the d coordinate. The following image shows the two different representations (Cartesian vs Frenet).

Comparison of a planned trajectory in Cartesian and Frenet coordinates.

To use Frenet coordinates it is required to have a continouosly smooth reference path.

Reference Path

Frenet coordinates provide a mathematically simpler representation of a reference path, because its run length is described with the s axis. This reference path provides a rough reference to follow an arbitrary but curvature continuous course of the road. To avoid collisions, the planner must take care of other objects in the environment, either static or dynamic. Such objects are usually not avoided by the reference path.

A reference path can be represented in two different forms although for all representations a run length information, which represents the s axis, is required for the transformation.

  • Polynome
  • Spline (multiple polynomes)
  • Clothoid (special polynome)
  • Polyline (single points with run length information)

Clothoid

$$ x(l) = c0 + c1*l $$

Polyline

Transformation

The transformation from local vehicle coordinates to Frenet coordinates is based on the relations shown in the following image:

Transformation vehicle frame to Frenet frame.

Given a point $P_C$ in the vehicle frame search for the closest point $R_C$ on the reference path. The run length of $R_C$, which is known from the reference path points, determins the s coordinate of the transformed point $P_F$. If the reference path is sufficiently smooth (continuously differentiable) then the vector $\vec{PR}$ is orthogonal to the reference path at the point $R_C$. The signed length of $\vec{PR}$ determines the d coordinate of $P_F$. The sign is positive, if $P_C$ lies on the left along the run lenght of the reference path.

The procedure to transform a point $P_F$ from Frenet coordinates to the local vehicle frame in Cartesian coordinates is analogous. First, the point $R_C$, which lies on the reference path at run length $s$. Next, a normal unit vector $\vec{d}$ is determined, which, in this point, is orthogonal to the reference path. The direction of this vector points towards positive $d$ values and therefore points to the left with increasing run length $s$. Therefore, the vector $\vec{d}$ depends on the run length, which leads to:

$$ P_C(s,d) = R_C(s) + d \cdot \vec{d}(s) $$

Usage

Jupyter Notebook

In the python folder you find a Jupyter Notebook which shows the described planning algorithm.

Frenet GUI

Note: The Frenet GUI is not functional yet. Contributions are welcome. Here's the plan for this GUI:

Allows you to generate trajectories in a local (world) reference frame from two quintic polynomials. One polynomial describes the longitudinal direction and the other one the lateral. Providing a reference path and applying the Frenet coordinate transformation on this path will result in a trajectory.

Execute frenet.sh run the GUI. This will call uic (Qt's user interface compiler) to process the ui file. Afterwards the main.py will be executed.

Dependencies

The GUI was created with python3 in a conda environment:

conda create -n frenetenv python=3.6
conda activate frenetenv
conda install -c conda-forge pyside2
conda install -c conda-forge matplotlib

You can use the provided environment.yml to create a conda environment with the required dependendies:

conda create --name <env-name> --file environment.yml
conda activate <env-name>

References

Python code:

Helper Function

https://de.mathworks.com/matlabcentral/fileexchange/22441-curve-intersections