Seeed_Arduino_LIS3DHTR

Introduction

An Arduino library for 3-Axis Digital Accelerometer ±2g to 16g (LIS3DHTR).Acceleration data can be obtained using IIC interface and SPI interface.

How to install Arduino Library

please refer here.

Usage

// This example use I2C.
#include "LIS3DHTR.h"
#include <Wire.h>
LIS3DHTR<TwoWire> LIS; //IIC
#define WIRE Wire

void setup()
{
  Serial.begin(115200);
  while (!Serial)
  {
  };
  LIS.begin(WIRE, LIS3DHTR_ADDRESS_UPDATED); //IIC init
  delay(100);
  LIS.setOutputDataRate(LIS3DHTR_DATARATE_50HZ);

}
void loop()
{
  if (!LIS)
  {
    Serial.println("LIS3DHTR didn't connect.");
    while (1)
      ;
    return;
  }
  //3 axis
   Serial.print("x:"); Serial.print(LIS.getAccelerationX()); Serial.print("  ");
   Serial.print("y:"); Serial.print(LIS.getAccelerationY()); Serial.print("  ");
   Serial.print("z:"); Serial.println(LIS.getAccelerationZ());

}

API Reference

• begin(comm<TwoWire>, address<uint8_t>=0x18) : void

// Init device by IIC
LIS3DHTR<TwoWire> LIS; //IIC
LIS.begin(Wire, 0x19)

• begin(comm<SPIClass>, sspin<uint8_t>=SS) : void

// Init device by SPI
LIS3DHTR<SPIClass> LIS; //SPI
LIS.begin(SPI, 10); //SPI SS/CS

• setPoweMode(mode<power_type_t>) : void

// Set power mode
LIS.setPoweMode(POWER_MODE_NORMAL); // Normal mode
LIS.setPoweMode(POWER_MODE_LOW); // Low power mode

• setFullScaleRange(range<scale_type_t>) : void

// Set Full scale
LIS.setFullScaleRange(LIS3DHTR_RANGE_2G); // 2G
LIS.setFullScaleRange(LIS3DHTR_RANGE_4G); // 4G
LIS.setFullScaleRange(LIS3DHTR_RANGE_8G); // 8G
LIS.setFullScaleRange(LIS3DHTR_RANGE_16G); // 16G

• setOutputDataRate(odr<odr_type_t>) : void

// Set output data rate
LIS.setOutputDataRate(LIS3DHTR_DATARATE_POWERDOWN); // Power down
LIS.setOutputDataRate(LIS3DHTR_DATARATE_1HZ); // 1HZ
LIS.setOutputDataRate(LIS3DHTR_DATARATE_10HZ); // 10HZ
LIS.setOutputDataRate(LIS3DHTR_DATARATE_25HZ); // 25HZ
LIS.setOutputDataRate(LIS3DHTR_DATARATE_50HZ); // 50HZ
LIS.setOutputDataRate(LIS3DHTR_DATARATE_100HZ); // 100HZ
LIS.setOutputDataRate(LIS3DHTR_DATARATE_200HZ); // 200HZ
LIS.setOutputDataRate(LIS3DHTR_DATARATE_400HZ); // 400HZ
LIS.setOutputDataRate(LIS3DHTR_DATARATE_1_6KH); // 1.6kHZ
LIS.setOutputDataRate(LIS3DHTR_DATARATE_5KHZ); // 5KHZ

• available(void) : bool

// if new data
if(LIS.available){
  float x = LIS.getAccelerationX();
}

• getAcceleration(x<float *>, y<float *>, z<float *>) : void

// get acceleration
float x, y, z;
LIS.getAcceleration(&x, &y, &z);

• getAccelerationX(void) : float

// get acceleration x
float x = LIS.getAccelerationX();

• getAccelerationY(void) : float

// get acceleration y
float y = LIS.getAccelerationY();

• getAccelerationY(void) : float

// get acceleration z
float Z = LIS.getAccelerationZ();

• getTemperature(void) : int16_t

// get temperature, you need to execute LIS.openTemp() before get temperature
int16_t temp = LIS.getTemperature();

• openTemp(void) : void

// open temperature enable
LIS.openTemp();

• closeTemp(void) : void

// close temperature enable
LIS.closeTemp();

• readbitADC1(void) : uint16_t

// read ADC1
uint16_t adc1 = LIS.readbitADC1();

• readbitADC2(void) : uint16_t

// read ADC2
uint16_t adc2 = LIS.readbitADC2();

• readbitADC3(void) : uint16_t

// read ADC3
uint16_t adc3 = LIS.readbitADC3();

• reset(void) : void

// reset device
LIS.reset();

---

License

This software is written by seeed studio
and is licensed under The MIT License. Check License.txt for more information.

Contributing to this software is warmly welcomed. You can do this basically by
forking, committing modifications and then pulling requests (follow the links above
for operating guide). Adding change log and your contact into file header is encouraged.
Thanks for your contribution.

Seeed Studio is an open hardware facilitation company based in Shenzhen, China.
Benefiting from local manufacture power and convenient global logistic system,
we integrate resources to serve new era of innovation. Seeed also works with
global distributors and partners to push open hardware movement.