/
config.json.example
114 lines (89 loc) · 4.2 KB
/
config.json.example
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
{
"//": "general settings",
"general": {
"//": "how long to wait after startup for the network & API to become accessible",
"//": "useful if started after boot while the network is still being set up",
"//": "value is in seconds, specify 0 to wait forever until access succeeds",
"startup_timeout": 0,
"//": "directory where capture images will appear",
"//": "note: make sure that both the PIR capture command and the motion software",
"//": " write their images into exactly this directory!",
"image_dir": "/tmp/piCamBot",
"//": "delete captured image after sending them? recommended, otherwise your disk runs full",
"//": "note: this also purges (removes and re-creates) the image directory on startup",
"delete_images": true,
"//": "automatically arm device directly after startup?",
"arm": false
},
"//": "telegram-related settings",
"telegram": {
"//": "telegram bot authorization token",
"token": "YOUR_TELEGRAM_API_TOKEN",
"//": "telegram IDs of the bot owner(s). only owners can interact with the bot",
"owner_ids": [ YOUR_TELEGRAM_USER_ID ]
},
"//": "PIR (passive infrared) sensor related settings (for motion detection via PIR sensor)",
"pir": {
"//": "enable motion detection via PIR sensor?",
"enable": false,
"//": "GPIO input pin for reading from sensor",
"gpio": 17,
"//": "command for creating snapshots if motion is detected",
"capture_cmd": "raspistill -a 12 -dt -vf -hf -n -t 1500 -o /tmp/piCamBot/piCamBot_%d.jpg",
"__capture_cmd": "raspistill -a 12 -dt -vf -hf -n -t 5000 -tl 1000 -o /tmp/piCamBot/piCamBot_%d.jpg",
"//": "store time of last detected motion, even if not armed. will be included in status report.",
"creepy_mode": false
},
"//": "settings related to the software 'motion' (for motion detection via camera instead of PIR sensor)",
"motion": {
"//": "enable motion detection via camera?",
"enable": false,
"//": "pid file for stopping the motion daemon (process_id_file setting)",
"pid_file": "/tmp/motion/motion.pid",
"//": "command for starting motion (always use option -b for daemon mode!)",
"cmd": "motion -b -c /home/pi/picambot/motion.conf",
"//": "process name to send SIGKILL to in case stopping by PID is not possible",
"kill_name": "motion"
},
"//": "settings for capturing single shots",
"capture": {
"//": "command for creating a snapshot",
"//": "note: the resulting image should be located outside the usual image_dir,",
"//": " otherwise it gets ignored while motion tracking is disabled",
"cmd": "raspistill -t 2000 -a 12 -vf -hf -n -o /tmp/piCamBot.jpg",
"//": "where to find the image after capturing",
"file": "/tmp/piCamBot.jpg",
"//": "settings for LEDs during image capture",
"led": {
"//": "turn on LED(s) during image capture?",
"enable": true,
"//": "GPIO output pin for turning LED(s) on",
"gpio": 26
}
},
"//": "buzzer settings for acoustic alarms, e.g. for piezo buzzers",
"//": "note: each buzzer sequence is defined by 1's (buzzer on) and 0's (buzzer off)",
"//": " and a configurable duration before 'playing' the next character",
"//": "note: buzzer gets automatically turned off after each onetime sequence",
"//": " (so you don't need to terminate a onetime sequence with a 0",
"//": "note: if you want to disable the buzzer for specific sequences then just",
"//": " leave the corresponding sequences empty",
"buzzer": {
"//": "enable buzzer",
"enable": false,
"//": "GPIO output pin for enabling/disabling buzzer",
"gpio": 16,
"//": "duration of on and off periods for sequences, in seconds",
"duration": 0.2,
"//": "on/off sequence (continuous) during motion detection",
"seq_motion": "1110",
"//": "on/off sequence (onetime) when arming camera",
"seq_arm": "1",
"//": "on/off sequence (onetime) when disarming camera",
"seq_disarm": "101",
"//": "on/off sequence (onetime) when capturing single shots",
"seq_capture": "10101",
"//": "on/off sequence (onetime) for the /buzzer command",
"seq_buzzer": "11110110"
}
}