Applications

You can use Application support to graph performance statistics of many applications.

Different applications support a variety of ways to collect data:

By direct connection to the application
snmpd extend
The agent.

The monitoring of applications could be added before or after the hosts have been added to LibreNMS.

If multiple methods of collection are listed you only need to enable one.

SNMP Extend

When using the snmp extend method, the application discovery module will pick up which applications you have set up for monitoring automatically, even if the device is already in LibreNMS. The application discovery module is enabled by default for most *nix operating systems, but in some cases you will need to manually enable the application discovery module.

SUDO

One major thing to keep in mind when using SNMP extend is these run as the snmpd user that can be an unprivileged user. In these situations you need to use sudo.

To test if you need sudo, first check the user snmpd is running as. Then test if you can run the extend script as that user without issue. For example if snmpd is running as 'Debian-snmp' and we want to run the extend for proxmox, we check that the following run without error:

sudo -u Debian-snmp /usr/local/bin/proxmox

If it doesn't work, then you will need to use sudo with the extend command. For the example above, that would mean adding the line below to the sudoers file:

Debian-snmp ALL = NOPASSWD: /usr/local/bin/proxmox

Finally we would need to add sudo to the extend command, which would look like that for proxmox:

extend proxmox /usr/bin/sudo /usr/local/bin/proxmox

Enable the application discovery module

Edit the device for which you want to add this support
Click on the Modules tab and enable the applications module.
This will be automatically saved, and you should get a green confirmation pop-up message.

After you have enabled the application module, it would be wise to then also enable which applications you want to monitor, in the rare case where LibreNMS does not automatically detect it.

Note: Only do this if an application was not auto-discovered by LibreNMS during discovery and polling.

Enable the application(s) to be discovered

Go to the device you have just enabled the application module for.
Click on the Applications tab and select the applications you want to monitor.
This will also be automatically saved, and you should get a green confirmation pop-up message.

Agent

The unix-agent does not have a discovery module, only a poller module. That poller module is always disabled by default. It needs to be manually enabled if using the agent. Some applications will be automatically enabled by the unix-agent poller module. It is better to ensure that your application is enabled for monitoring. You can check by following the steps under the SNMP Extend heading.

Apache

Either use SNMP extend or use the agent.

Note that you need to install and configure the Apache mod_status module before trying the script.

SNMP Extend

Download the script onto the desired host (the host must be added to LibreNMS devices)

wget https://raw.githubusercontent.com/librenms/librenms-agent/master/snmp/apache-stats.py -O /etc/snmp/apache-stats.py

Make the script executable

chmod +x /etc/snmp/apache-stats.py

Create the cache directory, '/var/cache/librenms/' and make sure that it is owned by the user running the SNMP daemon.

mkdir -p /var/cache/librenms/

Verify it is working by running /etc/snmp/apache-stats.py Package urllib3 for python3 needs to be installed. In Debian-based systems for example you can achieve this by issuing:

apt-get install python3-urllib3

Edit your snmpd.conf file (usually /etc/snmp/snmpd.conf) and add:

extend apache /etc/snmp/apache-stats.py

Restart snmpd on your host
Test by running

snmpwalk <various options depending on your setup> localhost NET-SNMP-EXTEND-MIB::nsExtendOutput2Table

Agent

Install the agent on this device if it isn't already and copy the apache script to /usr/lib/check_mk_agent/local/

Verify it is working by running /usr/lib/check_mk_agent/local/apache (If you get error like "Can't locate LWP/Simple.pm". libwww-perl needs to be installed: apt-get install libwww-perl)
Create the cache directory, '/var/cache/librenms/' and make sure that it is owned by the user running the SNMP daemon.

mkdir -p /var/cache/librenms/

On the device page in Librenms, edit your host and check the Apache under the Applications tab.

Asterisk

A small shell script that reports various Asterisk call status.

SNMP Extend

Download the asterisk script to /etc/snmp/ on your asterisk server.

wget https://raw.githubusercontent.com/librenms/librenms-agent/master/snmp/asterisk -O /etc/snmp/asterisk

Make the script executable

chmod +x /etc/snmp/asterisk

Configure ASCLI in the script.
Verify it is working by running /etc/snmp/asterisk
Edit your snmpd.conf file (usually /etc/snmp/snmpd.conf) and add:

extend asterisk /etc/snmp/asterisk

Restart snmpd on your host

The application should be auto-discovered as described at the top of the page. If it is not, please follow the steps set out under SNMP Extend heading top of page.

backupninja

A small shell script that reports status of last backupninja backup.

SNMP Extend

Download the backupninja script to /etc/snmp/backupninja.py on your backuped server.

wget https://raw.githubusercontent.com/librenms/librenms-agent/master/snmp/backupninja.py -O /etc/snmp/backupninja.py`

Make the script executable:

chmod +x /etc/snmp/backupninja.py

Edit your snmpd.conf file (usually /etc/snmp/snmpd.conf) and add:

extend backupninja /etc/snmp/backupninja.py

Restart snmpd on your host

BIND9 aka named

Create stats file with appropriate permissions:

~$ touch /var/cache/bind/stats
~$ chown bind:bind /var/cache/bind/stats

Change user:group to the user and group that's running bind/named.

Bind/named configuration:

options {
    ...
    statistics-file "/var/cache/bind/stats";
    zone-statistics yes;
    ...
};

Restart your bind9/named after changing the configuration.
Verify that everything works by executing rndc stats && cat /var/cache/bind/stats. In case you get a Permission Denied error, make sure you changed the ownership correctly.
Also be aware that this file is appended to each time rndc stats is called. Given this it is suggested you setup file rotation for it. Alternatively you can also set zero_stats to 1 in the config.
The script for this also requires the Perl module File::ReadBackwards.

FreeBSD       => p5-File-ReadBackwards
CentOS/RedHat => perl-File-ReadBackwards
Debian/Ubuntu => libfile-readbackwards-perl

If it is not available, it can be installed by cpan -i File::ReadBackwards.

You may possibly need to configure the agent/extend script as well.

The config file's path defaults to the same path as the script, but with .config appended. So if the script is located at /etc/snmp/bind, the config file will be /etc/snmp/bind.config. Alternatively you can also specify a config via -c $file.

Anything starting with a # is comment. The format for variables are $variable=$value. Empty lines are ignored. Spaces and tabs at either the start or end of a line are ignored.

Content of an example /etc/snmp/bind.config . Please edit with your own settings.

rndc = The path to rndc. Default: /usr/bin/env rndc
call_rndc = A 0/1 boolean on whether or not to call rndc stats.
    Suggest to set to 0 if using netdata. Default: 1
stats_file = The path to the named stats file. Default: /var/cache/bind/stats
agent = A 0/1 boolean for if this is being used as a LibreNMS
    agent or not. Default: 0
zero_stats = A 0/1 boolean for if the stats file should be zeroed
    first. Default: 0 (1 if guessed)

If you want to guess at the configuration, call the script with -g and it will print out what it thinks it should be.

SNMP Extend

Copy the bind shell script, to the desired host.

wget https://github.com/librenms/librenms-agent/raw/master/snmp/bind -O /etc/snmp/bind

Make the script executable

chmod +x /etc/snmp/bind

Edit your snmpd.conf file and add:

extend bind /etc/snmp/bind

Restart snmpd on the host in question.

The application should be auto-discovered as described at the top of the page. If it is not, please follow the steps set out under SNMP Extend heading top of page.

Agent

Install the agent on this device if it isn't already and copy the script to /usr/lib/check_mk_agent/local/bind via wget https://raw.githubusercontent.com/librenms/librenms-agent/master/snmp/bind -O /usr/lib/check_mk_agent/local/bind
Make the script executable

chmod +x /usr/lib/check_mk_agent/local/bind

Set the variable 'agent' to '1' in the config.

Certificate

A small python3 script that checks age and remaining validity of certificates

This script needs following packages on Debian/Ubuntu Systems:

python3
python3-openssl

Content of an example /etc/snmp/certificate.json . Please edit with your own settings.

{"domains": [
    {"fqdn": "www.mydomain.com"},
    {"fqdn": "some.otherdomain.org",
     "port": 8443},
    {"fqdn": "personal.domain.net"}
]
}

Key 'domains' contains a list of domains to check. Optional you can define a port. By default it checks on port 443.

SNMP Extend

Copy the shell script to the desired host.

wget https://raw.githubusercontent.com/librenms/librenms-agent/master/snmp/certificate.py -O /etc/snmp/certificate.py

Make the script executable

chmod +x /etc/snmp/certificate.py

Edit your snmpd.conf file (usually /etc/snmp/snmpd.conf) and add:

extend certificate /etc/snmp/certificate.py

Restart snmpd on your host

The application should be auto-discovered as described at the top of the page. If it is not, please follow the steps set out under SNMP Extend heading top of page.

C.H.I.P

C.H.I.P. is a $9 R8 based tiny computer ideal for small projects. Further details: https://getchip.com/pages/chip

Copy the shell script to the desired host.

wget https://raw.githubusercontent.com/librenms/librenms-agent/master/snmp/chip.sh -O /etc/snmp/power-stat.sh

Make the script executable

chmod +x /etc/snmp/power-stat.sh

Edit your snmpd.conf file (usually /etc/snmp/snmpd.conf) and add:

extend power-stat /etc/snmp/power-stat.sh

Restart snmpd on your host

The application should be auto-discovered as described at the top of the page. If it is not, please follow the steps set out under SNMP Extend heading top of page.

Docker Stats

It allows you to know which container docker run and their stats.

This script require: jq

SNMP Extend

Install jq

sudo apt install jq

Copy the shell script to the desired host.

wget https://github.com/librenms/librenms-agent/raw/master/snmp/docker-stats.sh -O /etc/snmp/docker-stats.sh

Make the script executable

chmod +x /etc/snmp/docker-stats.sh

Edit your snmpd.conf file (usually /etc/snmp/snmpd.conf) and add:

extend docker /etc/snmp/docker-stats.sh

If your run Debian, you need to add the Debian-snmp user to the docker group

usermod -a -G docker Debian-snmp

Restart snmpd on your host

systemctl restart snmpd

Entropy

A small shell script that checks your system's available random entropy.

SNMP Extend

Download the script onto the desired host.

wget https://raw.githubusercontent.com/librenms/librenms-agent/master/snmp/entropy.sh -O /etc/snmp/entropy.sh

Make the script executable

chmod +x /etc/snmp/entropy.sh

Edit your snmpd.conf file (usually /etc/snmp/snmpd.conf) and add:

extend entropy /etc/snmp/entropy.sh

Restart snmpd on your host

The application should be auto-discovered as described at the top of the page. If it is not, please follow the steps set out under SNMP Extend heading top of page.

EXIM Stats

SNMP extend script to get your exim stats data into your host.

SNMP Extend

Download the script onto the desired host.

wget https://raw.githubusercontent.com/librenms/librenms-agent/master/snmp/exim-stats.sh -O /etc/snmp/exim-stats.sh

Make the script executable

chmod +x /etc/snmp/exim-stats.sh

Edit your snmpd.conf file (usually /etc/snmp/snmpd.conf) and add:

extend exim-stats /etc/snmp/exim-stats.sh

If you are using sudo edit your sudo users (usually visudo) and add at the bottom:

snmp ALL=(ALL) NOPASSWD: /etc/snmp/exim-stats.sh, /usr/bin/exim*

Restart snmpd on your host

The application should be auto-discovered as described at the top of the page. If it is not, please follow the steps set out under SNMP Extend heading top of page.

Fail2ban

SNMP Extend

Copy the shell script, fail2ban, to the desired host.

wget https://github.com/librenms/librenms-agent/raw/master/snmp/fail2ban -O /etc/snmp/fail2ban

Make the script executable

chmod +x /etc/snmp/fail2ban

Edit your snmpd.conf file (usually /etc/snmp/snmpd.conf) and add:

extend fail2ban /etc/snmp/fail2ban

1. If you want to use the cache, it is as below, by using the -c switch.
```
extend fail2ban /etc/snmp/fail2ban -c
```

2. If you want to use the cache and update it if needed, this can by using the -c and -U switches.
```
extend fail2ban /etc/snmp/fail2ban -c -U
```

3. If you need to specify a custom location for the fail2ban-client, that can be done via the -f switch.
```
extend fail2ban /etc/snmp/fail2ban -f /foo/bin/fail2ban-client
```
If not specified, "/usr/bin/env fail2ban-client" is used.

Restart snmpd on your host
If you wish to use caching, add the following to /etc/crontab and restart cron.

*/3    *    *    *    *    root    /etc/snmp/fail2ban -u

Restart or reload cron on your system.

If you have more than a few jails configured, you may need to use caching as each jail needs to be polled and fail2ban-client can't do so in a timely manner for than a few. This can result in failure of other SNMP information being polled.

For additional details of the switches, please see the POD in the script it self at the top.

FreeBSD NFS Client

SNMP Extend

Copy the shell script, fbsdnfsserver, to the desired host

wget https://github.com/librenms/librenms-agent/raw/master/snmp/fbsdnfsclient -O /etc/snmp/fbsdnfsclient

Make the script executable

chmod +x /etc/snmp/fbsdnfsclient

Edit your snmpd.conf file and add:

extend fbsdnfsclient /etc/snmp/fbsdnfsclient

Restart snmpd on your host

The application should be auto-discovered as described at the top of the page. If it is not, please follow the steps set out under SNMP Extend heading top of page.

FreeBSD NFS Server

SNMP Extend

Copy the shell script, fbsdnfsserver, to the desired host

wget https://github.com/librenms/librenms-agent/raw/master/snmp/fbsdnfsserver -O /etc/snmp/fbsdnfsserver

Make the script executable

chmod +x /etc/snmp/fbsdnfsserver

Edit your snmpd.conf file and add:

extend fbsdnfsserver /etc/snmp/fbsdnfsserver

Restart snmpd on your host

The application should be auto-discovered as described at the top of the page. If it is not, please follow the steps set out under SNMP Extend heading top of page.

FreeRADIUS

The FreeRADIUS application extension requires that status_server be enabled in your FreeRADIUS config. For more information see: https://wiki.freeradius.org/config/Status

You should note that status requests increment the FreeRADIUS request stats. So LibreNMS polls will ultimately be reflected in your stats/charts.

Go to your FreeRADIUS configuration directory (usually /etc/raddb or /etc/freeradius).
cd sites-enabled
ln -s ../sites-available/status status
Restart FreeRADIUS.
You should be able to test with the radclient as follows...

echo "Message-Authenticator = 0x00, FreeRADIUS-Statistics-Type = 31, Response-Packet-Type = Access-Accept" | \
radclient -x localhost:18121 status adminsecret

Note that adminsecret is the default secret key in status_server. Change if you've modified this.

SNMP Extend

Copy the freeradius shell script, to the desired host.

wget https://raw.githubusercontent.com/librenms/librenms-agent/master/snmp/freeradius.sh -O /etc/snmp/freeradius.sh

Make the script executable

chmod +x /etc/snmp/freeradius.sh

If you've made any changes to the FreeRADIUS status_server config (secret key, port, etc.) edit freeradius.sh and adjust the config variable accordingly.
Edit your snmpd.conf file and add:

extend freeradius /etc/snmp/freeradius.sh

Restart snmpd on the host in question.

The application should be auto-discovered as described at the top of the page. If it is not, please follow the steps set out under SNMP Extend heading top of page.

Agent

Install the script to your agent

wget https://raw.githubusercontent.com/librenms/librenms-agent/master/snmp/freeradius.sh -O /usr/lib/check_mk_agent/local/freeradius.sh`

Make the script executable

chmod +x /usr/lib/check_mk_agent/local/freeradius.sh

If you've made any changes to the FreeRADIUS status_server config (secret key, port, etc.) edit freeradius.sh and adjust the config variable accordingly.
Edit the freeradius.sh script and set the variable 'AGENT' to '1' in the config.

Freeswitch

A small shell script that reports various Freeswitch call status.

Agent

Install the agent on this device if it isn't already and copy the freeswitch script to /usr/lib/check_mk_agent/local/

wget https://raw.githubusercontent.com/librenms/librenms-agent/master/agent-local/freeswitch -O /usr/lib/check_mk_agent/local/freeswitch`

Make the script executable

chmod +x /usr/lib/check_mk_agent/local/freeswitch

Configure FSCLI in the script. You may also have to create an /etc/fs_cli.conf file if your fs_cli command requires authentication.
Verify it is working by running /usr/lib/check_mk_agent/local/freeswitch

SNMP Extend

Download the script onto the desired host

wget https://github.com/librenms/librenms-agent/raw/master/agent-local/freeswitch -O /etc/snmp/freeswitch

Make the script executable

chmod +x /etc/snmp/freeswitch

Configure FSCLI in the script. You may also have to create an /etc/fs_cli.conf file if your fs_cli command requires authentication.
Verify it is working by running /etc/snmp/freeswitch
Edit your snmpd.conf file (usually /etc/snmp/snmpd.conf) and add:

extend freeswitch /etc/snmp/freeswitch

Restart snmpd on your host

The application should be auto-discovered as described at the top of the page. If it is not, please follow the steps set out under SNMP Extend heading top of page.

GPSD

SNMP Extend

Download the script onto the desired host.

wget https://raw.githubusercontent.com/librenms/librenms-agent/master/snmp/gpsd -O /etc/snmp/gpsd

Make the script executable

chmod +x /etc/snmp/gpsd

Edit your snmpd.conf file (usually /etc/snmp/snmpd.conf) and add:

extend gpsd /etc/snmp/gpsd

Restart snmpd on your host

The application should be auto-discovered as described at the top of the page. If it is not, please follow the steps set out under SNMP Extend heading at the top of the page.

Agent

Install the agent on this device if it isn't already and copy the gpsd script to /usr/lib/check_mk_agent/local/

You may need to configure $server or $port.

Verify it is working by running /usr/lib/check_mk_agent/local/gpsd

Icecast

Shell script that reports load average/memory/open-files stats of Icecast

SNMP Extend

Copy the shell script, icecast-stats.sh, to the desired host (the host must be added to LibreNMS devices)

wget https://github.com/librenms/librenms-agent/raw/master/snmp/icecast-stats.sh -O /etc/snmp/icecast-stats.sh

Make the script executable

chmod +x /etc/snmp/icecast-stats.sh

Verify it is working by running /etc/snmp/icecast-stats.sh
Edit your snmpd.conf file (usually /etc/snmp/icecast-stats.sh) and add:

extend icecast /etc/snmp/icecast-stats.sh

ISC DHCP Stats

A small python3 script that reports current DHCP leases stats and pool usage of ISC DHCP Server.

Also you have to install the dhcpd-pools Package. Under Ubuntu/Debian just run apt install dhcpd-pools

SNMP Extend

Copy the shell script to the desired host.

wget https://github.com/librenms/librenms-agent/raw/master/snmp/dhcp.py -O /etc/snmp/dhcp.py

Make the script executable

chmod +x /etc/snmp/dhcp.py

Edit your config file, Content of an example /etc/snmp/dhcp.json

{"leasefile": "/var/lib/dhcp/dhcpd.leases" }

Key 'leasefile' specifies the path to your lease file.

Edit your snmpd.conf file (usually /etc/snmp/snmpd.conf) and add:

extend dhcpstats /etc/snmp/dhcp.py

Restart snmpd on your host

The application should be auto-discovered as described at the top of the page. If it is not, please follow the steps set out under SNMP Extend heading top of page.

mailcow-dockerized postfix

SNMP Extend

Download the script into the desired host.

wget https://raw.githubusercontent.com/librenms/librenms-agent/master/snmp/mailcow-dockerized-postfix -O /etc/snmp/mailcow-dockerized-postfix

Make the script executable

chmod +x /etc/snmp/mailcow-dockerized-postfix

Maybe you will need to install pflogsumm on debian based OS. Please check if you have package installed.

Edit your snmpd.conf file (usually /etc/snmp/snmpd.conf) and add:

extend mailcow-postfix /etc/snmp/mailcow-dockerized-postfix

Restart snmpd on your host

The application should be auto-discovered as described at the top of the page. If it is not, please follow the steps set out under SNMP Extend heading top of page.

Mailscanner

SNMP Extend

Download the script onto the desired host.

wget https://raw.githubusercontent.com/librenms/librenms-agent/master/snmp/mailscanner.php -O /etc/snmp/mailscanner.php

Make the script executable

chmod +x /etc/snmp/mailscanner.php

Edit your snmpd.conf file (usually /etc/snmp/snmpd.conf) and add:

extend mailscanner /etc/snmp/mailscanner.php

Restart snmpd on your host

The application should be auto-discovered as described at the top of the page. If it is not, please follow the steps set out under SNMP Extend heading top of page.

Mdadm

It allows you to checks mdadm health and array data

This script require: jq

SNMP Extend

Install jq

sudo apt install jq

Download the script onto the desired host.

sudo wget https://raw.githubusercontent.com/librenms/librenms-agent/master/snmp/mdadm -O /etc/snmp/mdadm

Make the script executable

sudo chmod +x /etc/snmp/mdadm

Edit your snmpd.conf file (usually /etc/snmp/snmpd.conf) and add:

extend mdadm /etc/snmp/mdadm

Verify it is working by running

sudo /etc/snmp/mdadm

Restart snmpd on your host

sudo service snmpd restart

The application should be auto-discovered as described at the top of the page. If it is not, please follow the steps set out under SNMP Extend heading top of page.

MegaRAID

This software from Broadcom/LSI let you monitor MegaRAID controller.

Download the external software and follow the included install instructions.
Add the following line to your snmpd.conf file (usually /etc/snmp/snmpd.conf)

pass .1.3.6.1.4.1.3582 /usr/sbin/lsi_mrdsnmpmain

Restart snmpd on your host

Memcached

SNMP Extend

Copy the memcached script to /etc/snmp/ on your remote server.

wget https://raw.githubusercontent.com/librenms/librenms-agent/master/snmp/memcached -O /etc/snmp/memcached

Make the script executable:

chmod +x /etc/snmp/memcached

Edit your snmpd.conf file (usually /etc/snmp/snmpd.conf) and add:

extend memcached /etc/snmp/memcached

Restart snmpd on your host

The application should be auto-discovered as described at the top of the page. If it is not, please follow the steps set out under SNMP Extend heading top of page.

Munin

Agent

Install the script to your agent:

wget https://raw.githubusercontent.com/librenms/librenms-agent/master/agent-local/munin -O /usr/lib/check_mk_agent/local/munin

Make the script executable

chmod +x /usr/lib/check_mk_agent/local/munin

Create the munin scripts dir:

mkdir -p /usr/share/munin/munin-scripts

Install your munin scripts into the above directory.

To create your own custom munin scripts, please see this example:

#!/bin/bash
if [ "$1" = "config" ]; then
    echo 'graph_title Some title'
    echo 'graph_args --base 1000 -l 0' #not required
    echo 'graph_vlabel Some label'
    echo 'graph_scale no' #not required, can be yes/no
    echo 'graph_category system' #Choose something meaningful, can be anything
    echo 'graph_info This graph shows something awesome.' #Short desc
    echo 'foobar.label Label for your unit' # Repeat these two lines as much as you like
    echo 'foobar.info Desc for your unit.'
    exit 0
fi
echo -n "foobar.value " $(date +%s) #Populate a value, here unix-timestamp

MySQL

Create the cache directory, '/var/cache/librenms/' and make sure that it is owned by the user running the SNMP daemon.

mkdir -p /var/cache/librenms/

The MySQL script requires PHP-CLI and the PHP MySQL extension, so please verify those are installed.

CentOS (May vary based on PHP version)

yum install php-cli php-mysql

Debian (May vary based on PHP version)

apt-get install php-cli php-mysql

Unlike most other scripts, the MySQL script requires a configuration file mysql.cnf in the same directory as the extend or agent script with following content:

<?php
$mysql_user = 'root';
$mysql_pass = 'toor';
$mysql_host = 'localhost';
$mysql_port = 3306;

Note that depending on your MySQL installation (chrooted install for example), you may have to specify 127.0.0.1 instead of localhost. Localhost make a MySQL connection via the mysql socket, while 127.0.0.1 make a standard IP connection to mysql.

Note also if you get a mysql error Uncaught TypeError: mysqli_num_rows(): Argument #1, this is because you are using a newer mysql version which doesnt support UNBLOCKING for slave statuses, so you need to also include the line $chk_options['slave'] = false; into mysql.cnf to skip checking slave statuses

Agent

Install the agent on this device if it isn't already

and copy the mysql script to /usr/lib/check_mk_agent/local/

Verify it is working by running /usr/lib/check_mk_agent/local/mysql

SNMP extend

Copy the mysql script to the desired host.

wget https://github.com/librenms/librenms-agent/raw/master/snmp/mysql -O /etc/snmp/mysql

Make the file executable

chmod +x /etc/snmp/mysql

Edit /etc/snmp/mysql to set your MySQL connection constants or declare them in /etc/snmp/mysql.cnf (new file)
Edit your snmpd.conf file and add:

extend mysql /etc/snmp/mysql

Restart snmpd.

The application should be auto-discovered as described at the top of the page. If it is not, please follow the steps set out under SNMP Extend heading top of page.

NGINX

NGINX is a free, open-source, high-performance HTTP server: https://www.nginx.org/

It's required to have the following directive in your nginx configuration responsible for the localhost server:

location /nginx-status {
    stub_status on;
    access_log  off;
    allow 127.0.0.1;
    allow ::1;
    deny  all;
}

SNMP Extend

Download the script onto the desired host.

wget https://raw.githubusercontent.com/librenms/librenms-agent/master/snmp/nginx -O /etc/snmp/nginx

Make the script executable

chmod +x /etc/snmp/nginx

Edit your snmpd.conf file (usually /etc/snmp/snmpd.conf) and add:

extend nginx /etc/snmp/nginx

Restart snmpd on your host

The application should be auto-discovered as described at the top of the page. If it is not, please follow the steps set out under SNMP Extend heading top of page.

Agent

Install the agent on this device if it isn't already and copy the nginx script to /usr/lib/check_mk_agent/local/

NFS Server

Export the NFS stats from as server.

SNMP Extend

Edit your snmpd.conf file (usually /etc/snmp/snmpd.conf) and add :

extend nfs-server /bin/cat /proc/net/rpc/nfsd

find out where cat is located using : which cat

reload snmpd service to activate the configuration

NTP Client

A shell script that gets stats from ntp client.

SNMP Extend

Download the script onto the desired host.

wget https://raw.githubusercontent.com/librenms/librenms-agent/master/snmp/ntp-client -O /etc/snmp/ntp-client

Make the script executable

chmod +x /etc/snmp/ntp-client

Edit your snmpd.conf file (usually /etc/snmp/snmpd.conf) and add:

extend ntp-client /etc/snmp/ntp-client

Restart snmpd on your host

The application should be auto-discovered as described at the top of the page. If it is not, please follow the steps set out under SNMP Extend heading top of page.

NTP Server aka NTPD

A shell script that gets stats from ntp server (ntpd).

SNMP Extend

Download the script onto the desired host.

wget https://raw.githubusercontent.com/librenms/librenms-agent/master/snmp/ntp-server.sh -O /etc/snmp/ntp-server.sh

Make the script executable

chmod +x /etc/snmp/ntp-server.sh

Edit your snmpd.conf file (usually /etc/snmp/snmpd.conf) and add:

extend ntp-server /etc/snmp/ntp-server.sh

Restart snmpd on your host

The application should be auto-discovered as described at the top of the page. If it is not, please follow the steps set out under SNMP Extend heading top of page.

Chronyd

A shell script that gets the stats from chronyd and exports them with SNMP Extend.

SNMP Extend

Download the shell script onto the desired host

wget https://raw.githubusercontent.com/librenms/librenms-agent/master/snmp/chrony -O /etc/snmp/chrony

Make the script executable

chmod +x /etc/snmp/chrony

Edit the snmpd.conf file to include the extend by adding the following line to the end of the config file:

extend chronyd /etc/snmp/chrony

Note: Some distributions need sudo-permissions for the script to work with SNMP Extend. See the instructions on the section SUDO for more information.

Restart snmpd service on the host

Application should be auto-discovered and its stats presented on the Apps-page on the host. Note: Applications module needs to be enabled on the host or globally for the statistics to work as intended.

Nvidia GPU

SNMP Extend

Copy the shell script, nvidia, to the desired host

wget https://github.com/librenms/librenms-agent/raw/master/snmp/nvidia -O /etc/snmp/nvidia

Make the script executable

chmod +x /etc/snmp/nvidia

Edit your snmpd.conf file and add:

extend nvidia /etc/snmp/nvidia

Restart snmpd on your host.
Verify you have nvidia-smi installed, which it generally should be if you have the driver from Nvida installed.

The GPU numbering on the graphs will correspond to how the nvidia-smi sees them as being.

For questions about what the various values are/mean, please see the nvidia-smi man file under the section covering dmon.

Opensearch\Elasticsearch

SNMP Extend

Download the script onto the desired host.

wget https://raw.githubusercontent.com/librenms/librenms-agent/master/snmp/opensearch -O /etc/snmp/opensearch

Make it executable

chmod +x /etc/snmp/opensearch

Install the required Perl dependencies.

# FreeBSD
pkg install p5-JSON p5-libwww
# Debian/Ubuntu
apt-get install libjson-perl libwww-perl
# cpanm
cpanm JSON Libwww

Update your snmpd.conf.

extend opensearch /bin/cat /var/cache/opensearch.json

Update root crontab with. This is required as it will this will likely time out otherwise. Use */1 if you want to have the most recent stats when polled or to */5 if you just want at exactly a 5 minute interval.

*/5 * * * * /etc/snmp/opensearch > /var/cache/opensearch.json

Enable it or wait for the device to be re-disocvered.

Open Grid Scheduler

Shell script to track the OGS/GE jobs running on clusters.

SNMP Extend

Download the script onto the desired host.

wget https://raw.githubusercontent.com/librenms/librenms-agent/master/agent-local/rocks.sh -O /etc/snmp/rocks.sh

Make the script executable

chmod +x /etc/snmp/rocks.sh

Edit your snmpd.conf file (usually /etc/snmp/snmpd.conf) and add:

extend ogs /etc/snmp/rocks.sh

Restart snmpd.

The application should be auto-discovered as described at the top of the page. If it is not, please follow the steps set out under SNMP Extend heading top of page.

Opensips

Script that reports load-average/memory/open-files stats of Opensips

SNMP Extend

Download the script onto the desired host

wget https://raw.githubusercontent.com/librenms/librenms-agent/master/snmp/opensips-stats.sh -O /etc/snmp/opensips-stats.sh

Make the script executable:

chmod +x /etc/snmp/opensips-stats.sh

Verify it is working by running /etc/snmp/opensips-stats.sh
Edit your snmpd.conf file (usually /etc/snmp/snmpd.conf) and add:

extend opensips /etc/snmp/opensips-stats.sh

OS Updates

A small shell script that checks your system package manager for any available updates. Supports apt-get/pacman/yum/zypper package managers.

For pacman users automatically refreshing the database, it is recommended you use an alternative database location --dbpath=/var/lib/pacman/checkupdate

SNMP Extend

Download the script onto the desired host.

wget https://raw.githubusercontent.com/librenms/librenms-agent/master/snmp/osupdate -O /etc/snmp/osupdate

Make the script executable

chmod +x /etc/snmp/osupdate

Edit your snmpd.conf file (usually /etc/snmp/snmpd.conf) and add:

extend osupdate /etc/snmp/osupdate

Restart snmpd on your host

Note: apt-get depends on an updated package index. There are several ways to have your system run apt-get update automatically. The easiest is to create /etc/apt/apt.conf.d/10periodic and pasting the following in it: APT::Periodic::Update-Package-Lists "1";. If you have apticron, cron-apt or apt-listchanges installed and configured, chances are that packages are already updated periodically .

The application should be auto-discovered as described at the top of the page. If it is not, please follow the steps set out under SNMP Extend heading top of page.

PHP-FPM

SNMP Extend

Copy the shell script, phpfpmsp, to the desired host

wget https://github.com/librenms/librenms-agent/raw/master/snmp/phpfpmsp -O /etc/snmp/phpfpmsp

Make the script executable

chmod +x /etc/snmp/phpfpmsp

Edit your snmpd.conf file (usually /etc/snmp/snmpd.conf) and add:

extend phpfpmsp /etc/snmp/phpfpmsp

Edit /etc/snmp/phpfpmsp to include the status URL for the PHP-FPM pool you are monitoring.
Restart snmpd on your host

It is worth noting that this only monitors a single pool. If you want to monitor multiple pools, this won't do it.

The application should be auto-discovered as described at the top of the page. If it is not, please follow the steps set out under SNMP Extend heading top of page.

Agent

Install the agent on this device if it isn't already and copy the phpfpmsp script to /usr/lib/check_mk_agent/local/

Pi-hole

SNMP Extend

Copy the shell script, pi-hole, to the desired host.

wget https://github.com/librenms/librenms-agent/raw/master/snmp/pi-hole -O /etc/snmp/pi-hole

Make the script executable

chmod +x /etc/snmp/pi-hole

Edit your snmpd.conf file and add:

extend pi-hole /etc/snmp/pi-hole

To get all data you must get your API auth token from Pi-hole server and change the API_AUTH_KEY entry inside the snmp script.
Restard snmpd.

The application should be auto-discovered as described at the top of the page. If it is not, please follow the steps set out under SNMP Extend heading top of page.

Portactivity

SNMP Extend

Install missing packages - Ubuntu is shown below.

apt install libparse-netstat-perl
apt install libjson-perl

Copy the Perl script to the desired host (the host must be added to LibreNMS devices)

wget https://github.com/librenms/librenms-agent/raw/master/snmp/portactivity -O /etc/snmp/portactivity

Make the script executable

chmod +x /etc/snmp/portactivity

Edit your snmpd.conf file (usually /etc/snmp/snmpd.conf) and add:

extend portactivity /etc/snmp/portactivity -p http,ldap,imap

Will monitor HTTP, LDAP, and IMAP. The -p switch specifies what ports to use. This is a comma seperated list.

These must be found in '/etc/services' or where ever NSS is set to fetch it from. If not, it will throw an error.

If you want to JSON returned by it to be printed in a pretty format use the -P flag.

Restart snmpd on your host.

Please note that for only TCP[46] services are supported.

Postfix

SNMP Extend

Copy the shell script, postfix-queues, to the desired host

wget https://github.com/librenms/librenms-agent/raw/master/snmp/postfix-queues -O /etc/snmp/postfix-queues

Copy the Perl script, postfixdetailed, to the desired host

wget https://github.com/librenms/librenms-agent/raw/master/snmp/postfixdetailed -O /etc/snmp/postfixdetailed

Make both scripts executable

chmod +x /etc/snmp/postfixdetailed /etc/snmp/postfix-queues

Edit your snmpd.conf file and add:

extend mailq /etc/snmp/postfix-queues
extend postfixdetailed /etc/snmp/postfixdetailed

Restart snmpd.
Install pflogsumm for your OS.
Make sure the cache file in /etc/snmp/postfixdetailed is some place that snmpd can write too. This file is used for tracking changes between various values between each time it is called by snmpd. Also make sure the path for pflogsumm is correct.
Run /etc/snmp/postfixdetailed to create the initial cache file so you don't end up with some crazy initial starting value. Please note that each time /etc/snmp/postfixdetailed is ran, the cache file is updated, so if this happens in between LibreNMS doing it then the values will be thrown off for that polling period.

The application should be auto-discovered as described at the top of the page. If it is not, please follow the steps set out under SNMP Extend heading top of page.

NOTE: If using RHEL for your postfix server, qshape must be installed manually as it is not officially supported. CentOs 6 rpms seem to work without issues.

Postgres

SNMP Extend

Copy the shell script, postgres, to the desired host

wget https://github.com/librenms/librenms-agent/raw/master/snmp/postgres -O /etc/snmp/postgres

Make the script executable

chmod +x /etc/snmp/postgres

Edit your snmpd.conf file and add:

extend postgres /etc/snmp/postgres

Restart snmpd on your host
Install the Nagios check check_postgres.pl on your system: https://github.com/bucardo/check_postgres
Verify the path to check_postgres.pl in /etc/snmp/postgres is correct.
If you wish it to ignore the database postgres for totalling up the stats, set ignorePG to 1(the default) in /etc/snmp/postgres. If you are using netdata or the like, you may wish to set this or otherwise that total will be very skewed on systems with light or moderate usage.

The application should be auto-discovered as described at the top of the page. If it is not, please follow the steps set out under SNMP Extend heading top of page.

PowerDNS

An authoritative DNS server: https://www.powerdns.com/auth.html

SNMP Extend

Copy the shell script, powerdns.py, to the desired host

wget https://github.com/librenms/librenms-agent/raw/master/snmp/powerdns.py -O /etc/snmp/powerdns.py

Make the script executable

chmod +x /etc/snmp/powerdns.py

Edit your snmpd.conf file and add:

extend powerdns /etc/snmp/powerdns.py

Restart snmpd on your host

The application should be auto-discovered as described at the top of the page. If it is not, please follow the steps set out under SNMP Extend heading top of page.

Agent

Install the agent on this device if it isn't already and copy the powerdns script to /usr/lib/check_mk_agent/local/

PowerDNS Recursor

A recursive DNS server: https://www.powerdns.com/recursor.html

Direct

The LibreNMS polling host must be able to connect to port 8082 on the monitored device. The web-server must be enabled, see the Recursor docs: https://doc.powerdns.com/md/recursor/settings/#webserver

Variables

$config['apps']['powerdns-recursor']['api-key'] required, this is defined in the Recursor config

$config['apps']['powerdns-recursor']['port'] numeric, defines the port to connect to PowerDNS Recursor on. The default is 8082

$config['apps']['powerdns-recursor']['https'] true or false, defaults to use http.

SNMP Extend

Copy the shell script, powerdns-recursor, to the desired host

wget https://github.com/librenms/librenms-agent/raw/master/snmp/powerdns-recursor -O /etc/snmp/powerdns-recursor

Make the script executable

chmod +x /etc/snmp/powerdns-recursor

Edit your snmpd.conf file and add:

extend powerdns-recursor /etc/snmp/powerdns-recursor

Restart snmpd on your host

The application should be auto-discovered as described at the top of the page. If it is not, please follow the steps set out under SNMP Extend heading top of page.

Agent

Install the agent on this device if it isn't already and copy the powerdns-recursor script to /usr/lib/check_mk_agent/local/

This script uses rec_control get-all to collect stats.

PowerDNS-dnsdist

SNMP Extend

Copy the BASH script to the desired host.

wget https://github.com/librenms/librenms-agent/raw/master/snmp/powerdns-dnsdist -O /etc/snmp/powerdns-dnsdist

Make the script executable

chmod +x /etc/snmp/powerdns-dnsdist

Edit your snmpd.conf file (usually /etc/snmp/snmpd.conf) and add:

extend powerdns-dnsdist /etc/snmp/powerdns-dnsdist

Restart snmpd on your host.

The application should be auto-discovered as described at the top of the page. If it is not, please follow the steps set out under SNMP Extend heading top of page.

PowerMon

PowerMon tracks the power usage on your host and can report on both consumption and cost, using a python script installed on the host.

PowerMon consumption graph

Currently the script uses one of two methods to determine current power usage:

ACPI via libsensors
HP-Health (HP Proliant servers only)

The ACPI method is quite unreliable as it is usually only implemented by battery-powered devices, e.g. laptops. YMMV. However, it's possible to support any method as long as it can return a power value, usually in Watts.

TIP: You can achieve this by adding a method and a function for that method to the script. It should be called by getData() and return a dictionary.

Because the methods are unreliable for all hardware, you need to declare to the script which method to use. The are several options to assist with testing, see --help.

SNMP Extend

Initial setup

Download the python script onto the host:

wget https://raw.githubusercontent.com/librenms/librenms-agent/master/snmp/powermon-snmp.py -O /usr/local/bin/powermon-snmp.py

Make the script executable:

chmod +x /usr/local/bin/powermon-snmp.py

Edit the script and set the cost per kWh for your supply. You must uncomment this line for the script to work:

vi /usr/local/bin/powermon-snmp.py
#costPerkWh = 0.15

Choose you method below:

=== "Method 1. sensors"

 * Install dependencies:
 ```
 dnf install lm_sensors
 pip install PySensors
 ```

 * Test the script from the command-line. For example:
 ```
 $ /usr/local/bin/powermon-snmp.py -m sensors -n -p
 {
   "meter": {
     "0": {
       "reading": 0.0
     }
   },
   "psu": {},
   "supply": {
     "rate": 0.15
   },
   "reading": "0.0"
 }
 ```

 If you see a reading of `0.0` it is likely this method is not supported for
 your system. If not, continue.

=== "Method 2. hpasmcli"

 * Obtain the hp-health package for your system. Generally there are
 three options:
     * Standalone package from [HPE Support](https://support.hpe.com/hpsc/swd/public/detail?swItemId=MTX-c0104db95f574ae6be873e2064#tab2)
     * From the HP Management Component Pack (MCP).
     * Included in the [HP Service Pack for Proliant (SPP)](https://support.hpe.com/hpesc/public/docDisplay?docId=emr_na-a00026884en_us)

 * If you've downloaded the standalone package, install it. For example:
 ```
 rpm -ivh hp-health-10.91-1878.11.rhel8.x86_64.rpm
 ```

 * Check the service is running:
 ```
 systemctl status hp-health
 ```

 * Test the script from the command-line. For example:
 ```
 $ /usr/local/bin/powermon-snmp.py -m hpasmcli -n -p
 {
   "meter": {
     "1": {
       "reading": 338.0
     }
   },
   "psu": {
     "1": {
       "present": "Yes",
       "redundant": "No",
       "condition": "Ok",
       "hotplug": "Supported",
       "reading": 315.0
     },
     "2": {
       "present": "Yes",
       "redundant": "No",
       "condition": "FAILED",
       "hotplug": "Supported"
     }
   },
   "supply": {
     "rate": 0.224931
   },
   "reading": 338.0
 }
 ```

 If you see a reading of `0.0` it is likely this method is not supported for
 your system. If not, continue.

Finishing Up

Edit your snmpd.conf file (usually /etc/snmp/snmpd.conf) and add the following:

extend  powermon   /usr/local/bin/powermon-snmp.py -m hpasmcli

> NOTE: Avoid using other script options in the snmpd config as the results may not be
> interpreted correctly by LibreNMS.

Reload your snmpd service:

systemctl reload snmpd

You're now ready to enable the application in LibreNMS.

Pwrstatd

Pwrstatd (commonly known as powerpanel) is an application/service available from CyberPower to monitor their PSUs over USB. It is currently capable of reading the status of only one PSU connected via USB at a time. The powerpanel software is available here: https://www.cyberpowersystems.com/products/software/power-panel-personal/

SNMP Extend

Copy the python script, pwrstatd.py, to the desired host

wget https://github.com/librenms/librenms-agent/raw/master/snmp/pwrstatd.py -O /etc/snmp/pwrstatd.py

Make the script executable

chmod +x /etc/snmp/pwrstatd.py

Edit your snmpd.conf file and add:

extend pwrstatd /etc/snmp/pwrstatd.py

(Optional) Create a /etc/snmp/pwrstatd.json file and specify the path to the pwrstat executable [the default path is /sbin/pwrstat]:

{
    "pwrstat_cmd": "/sbin/pwrstat"
}

Restart snmpd.

Proxmox

For Proxmox 4.4+ install the libpve-apiclient-perl package

apt install libpve-apiclient-perl

Download the script onto the desired host

wget https://raw.githubusercontent.com/librenms/librenms-agent/master/agent-local/proxmox -O /usr/local/bin/proxmox

Make the script executable

chmod +x /usr/local/bin/proxmox

Edit your snmpd.conf file (usually /etc/snmp/snmpd.conf) and add:

extend proxmox /usr/local/bin/proxmox

Note: if your snmpd doesn't run as root, you might have to invoke the script using sudo and modify the "extend" line

extend proxmox /usr/bin/sudo /usr/local/bin/proxmox

after, edit your sudo users (usually visudo) and add at the bottom:

Debian-snmp ALL=(ALL) NOPASSWD: /usr/local/bin/proxmox

Restart snmpd on your host

Puppet Agent

SNMP extend script to get your Puppet Agent data into your host.

SNMP Extend

Download the script onto the desired host

wget https://raw.githubusercontent.com/librenms/librenms-agent/master/snmp/puppet_agent.py -O /etc/snmp/puppet_agent.py

Make the script executable

chmod +x /etc/snmp/puppet_agent.py

Edit your snmpd.conf file (usually /etc/snmp/snmpd.conf) and add:

extend puppet-agent /etc/snmp/puppet_agent.py

The Script needs python3-yaml package to be installed.

Per default script searches for on of this files:

/var/cache/puppet/state/last_run_summary.yaml
/opt/puppetlabs/puppet/cache/state/last_run_summary.yaml

optionally you can add a specific summary file with creating /etc/snmp/puppet.json

{
     "agent": {
        "summary_file": "/my/custom/path/to/summary_file"
     }
}

custom summary file has highest priority

Restart snmpd on the host

PureFTPd

SNMP extend script to monitor PureFTPd.

SNMP Extend

Download the script onto the desired host

wget https://raw.githubusercontent.com/librenms/librenms-agent/master/snmp/pureftpd.py -O /etc/snmp/pureftpd.py

Make the script executable

chmod +x /etc/snmp/pureftpd.py

Edit your snmpd.conf file (usually /etc/snmp/snmpd.conf) and add:

extend pureftpd sudo /etc/snmp/pureftpd.py

Edit your sudo users (usually visudo) and add at the bottom:

snmp ALL=(ALL) NOPASSWD: /etc/snmp/pureftpd.py

or the path where your pure-ftpwho is located

If pure-ftpwho is not located in /usr/sbin

you will also need to create a config file, which is named

pureftpd.json. The file has to be located in /etc/snmp/.

{"pureftpwho_cmd": "/usr/sbin/pure-ftpwho"
}

Restart snmpd on your host

Raspberry PI

SNMP extend script to get your PI data into your host.

SNMP Extend

Download the script onto the desired host

wget https://raw.githubusercontent.com/librenms/librenms-agent/master/snmp/raspberry.sh -O /etc/snmp/raspberry.sh

Make the script executable

chmod +x /etc/snmp/raspberry.sh

Edit your snmpd.conf file (usually /etc/snmp/snmpd.conf) and add:

extend raspberry /usr/bin/sudo /bin/sh /etc/snmp/raspberry.sh

Edit your sudo users (usually visudo) and add at the bottom:

snmp ALL=(ALL) NOPASSWD: /bin/sh /etc/snmp/raspberry.sh

Note: If you are using Raspian, the default user is Debian-snmp. Change snmp above to Debian-snmp. You can verify the user snmpd is using with ps aux | grep snmpd

Restart snmpd on PI host

Raspberry Pi GPIO Monitor

SNMP extend script to monitor your IO pins or sensor modules connected to your GPIO header.

SNMP Extend

1: Make sure you have wiringpi installed on your Raspberry Pi. In Debian-based systems for example you can achieve this by issuing:

apt-get install wiringpi

2: Download the script to your Raspberry Pi. wget https://raw.githubusercontent.com/librenms/librenms-agent/master/snmp/rpigpiomonitor.php -O /etc/snmp/rpigpiomonitor.php

3: (optional) Download the example configuration to your Raspberry Pi. wget https://raw.githubusercontent.com/librenms/librenms-agent/master/snmp/rpigpiomonitor.ini -O /etc/snmp/rpigpiomonitor.ini

4: Make the script executable: chmod +x /etc/snmp/rpigpiomonitor.php

5: Create or edit your rpigpiomonitor.ini file according to your needs.

6: Check your configuration with rpigpiomonitor.php -validate

7: Edit your snmpd.conf file (usually /etc/snmp/snmpd.conf) and add:

extend rpigpiomonitor /etc/snmp/rpigpiomonitor.php

8: Restart snmpd on your Raspberry Pi and, if your Raspberry Pi is already present in LibreNMS, perform a manual rediscover.

Redis

Script to monitor your Redis Server

SNMP Extend

Download the script onto the desired host

wget https://raw.githubusercontent.com/librenms/librenms-agent/master/snmp/redis.py -O /etc/snmp/redis.py

Make the script executable

chmod +x /etc/snmp/redis.py

Edit your snmpd.conf file (usually /etc/snmp/snmpd.conf) and add:

extend redis /etc/snmp/redis.py

Agent

Install the agent on this device if it isn't already and copy the redis script to /usr/lib/check_mk_agent/local/

RRDCached

Install/Setup: For Install/Setup Local Librenms RRDCached: Please see RRDCached

Will collect stats by:

Connecting directly to the associated device on port 42217
Monitor thru snmp with SNMP extend, as outlined below
Connecting to the rrdcached server specified by the rrdcached setting

SNMP extend script to monitor your (remote) RRDCached via snmp

SNMP Extend

Download the script onto the desired host

wget https://raw.githubusercontent.com/librenms/librenms-agent/master/agent-local/rrdcached -O /etc/snmp/rrdcached

Make the script executable

chmod +x /etc/snmp/rrdcached

Edit your snmpd.conf file (usually /etc/snmp/snmpd.conf) and add:

extend rrdcached /etc/snmp/rrdcached

SDFS info

A small shell script that exportfs SDFS volume info.

SNMP Extend

Download the script onto the desired host

wget https://raw.githubusercontent.com/librenms/librenms-agent/master/snmp/sdfsinfo -O /etc/snmp/sdfsinfo

Make the script executable

chmod +x /etc/snmp/sdfsinfo

Edit your snmpd.conf file (usually /etc/snmp/snmpd.conf) and add:

extend sdfsinfo /etc/snmp/sdfsinfo

Restart snmpd on your host

The application should be auto-discovered as described at the top of the page. If it is not, please follow the steps set out under SNMP Extend heading top of page.

Seafile

SNMP extend script to monitor your Seafile Server

SNMP Extend

Copy the Python script, seafile.py, to the desired host

wget https://github.com/librenms/librenms-agent/raw/master/snmp/seafile.py -O /etc/snmp/seafile.py

Also you have to install the requests Package for Python3. Under Ubuntu/Debian just run apt install python3-requests

Make the script executable

chmod +x /etc/snmp/seafile.py

Edit your snmpd.conf file and add:

extend seafile /etc/snmp/seafile.py

You will also need to create the config file, which is named seafile.json . The script has to be located at /etc/snmp/.

{"url": "https://seafile.mydomain.org",
 "username": "some_admin_login@mail.address",
 "password": "password",
 "account_identifier": "name"
 "hide_monitoring_account": true
}

The variables are as below.

url = Url how to get access to Seafile Server
username = Login to Seafile Server.
           It is important that used Login has admin privileges.
           Otherwise most API calls will be denied.
password = Password to the configured login.
account_identifier = Defines how user accounts are listed in RRD Graph.
                     Options are: name, email
hide_monitoring_account = With this Boolean you can hide the Account which you
                          use to access Seafile API

**Note:**It is recommended to use a dedicated Administrator account for monitoring.

SMART

SNMP Extend

Copy the Perl script, smart, to the desired host.

wget https://github.com/librenms/librenms-agent/raw/master/snmp/smart -O /etc/snmp/smart

Make the script executable

chmod +x /etc/snmp/smart

Edit your snmpd.conf file and add:

extend smart /etc/snmp/smart

You will also need to create the config file, which defaults to the same path as the script, but with .config appended. So if the script is located at /etc/snmp/smart, the config file will be /etc/snmp/smart.config. Alternatively you can also specific a config via -c.

Anything starting with a # is comment. The format for variables is $variable=$value. Empty lines are ignored. Spaces and tabes at either the start or end of a line are ignored. Any line with out a matched variable or # are treated as a disk.

#This is a comment
cache=/var/cache/smart
smartctl=/usr/bin/env smartctl
useSN=1
ada0
ada1
da5 /dev/da5 -d sat
twl0,0 /dev/twl0 -d 3ware,0
twl0,1 /dev/twl0 -d 3ware,1
twl0,2 /dev/twl0 -d 3ware,2

The variables are as below.

cache = The path to the cache file to use. Default: /var/cache/smart
smartctl = The path to use for smartctl. Default: /usr/bin/env smartctl
useSN = If set to 1, it will use the disks SN for reporting instead of the device name.
        1 is the default. 0 will use the device name.

A disk line is can be as simple as just a disk name under /dev/. Such as in the config above The line "ada0" would resolve to "/dev/ada0" and would be called with no special argument. If a line has a space in it, everything before the space is treated as the disk name and is what used for reporting and everything after that is used as the argument to be passed to smartctl.

If you want to guess at the configuration, call it with -g and it will print out what it thinks it should be.

Restart snmpd on your host

If you have a large number of more than one or two disks on a system, you should consider adding this to cron. Also make sure the cache file is some place it can be written to.

 */3 * * * * /etc/snmp/smart -u

If your snmp agent runs as user "snmp", edit your sudo users (usually visudo) and add at the bottom:

snmp ALL=(ALL) NOPASSWD: /etc/snmp/smart, /usr/bin/env smartctl

and modify your snmpd.conf file accordingly:

extend smart /usr/bin/sudo /etc/snmp/smart

The application should be auto-discovered as described at the top of the page. If it is not, please follow the steps set out under SNMP Extend heading top of page.

If you set useSN to 1, it is worth noting that you will loose history(not able to access it from the web interface) for that device each time you change it. You will also need to run camcontrol or the like on said server to figure out what device actually corresponds with that serial number.

Also if the system you are using uses non-static device naming based on bus information, it may be worthwhile just using the SN as the device ID is going to be irrelevant in that case.

Squid

SNMP Proxy

Enable SNMP for Squid like below, if you have not already, and restart it.

acl snmppublic snmp_community public
snmp_port 3401
snmp_access allow snmppublic localhost
snmp_access deny all

Restart squid on your host.
Edit your snmpd.conf file and add, making sure you have the same community, host, and port as above:

proxy -v 2c -Cc -c public 127.0.0.1.3401 1.3.6.1.4.1.3495

For more advanced information on Squid and SNMP or setting up proxying for net-snmp, please see the links below.

http://wiki.squid-cache.org/Features/Snmp http://www.net-snmp.org/wiki/index.php/Snmpd_proxy

Supervisord

It shows you the totals per status and also the uptime per process. That way you can add alerts for instance when there are process in state FATAL.

SNMP Extend

Copy the python script to the desired host.

wget https://github.com/librenms/librenms-agent/raw/master/snmp/supervisord.py -O /etc/snmp/supervisord.py

Notice that this will use the default unix socket path. Modify the unix_socket_path variable in the script if your path differs from the default.

Make the script executable

chmod +x /etc/snmp/supervisord.py

Edit your snmpd.conf file (usually /etc/snmp/snmpd.conf) and add:

extend supervisord /etc/snmp/supervisord.py

Restart snmpd on your host

systemctl restart snmpd

Sagan

For metrics the stats are migrated as below from the stats JSON.

f_drop_percent and drop_percent are computed based on the found data.

Instance Key	Stats JSON Key
uptime	.stats.uptime
total	.stats.captured.total
drop	.stats.captured.drop
ignore	.stats.captured.ignore
threshold	.stats.captured.theshold
after	.stats.captured.after
match	.stats.captured.match
bytes	.stats.captured.bytes_total
bytes_ignored	.stats.captured.bytes_ignored
max_bytes_log_line	.stats.captured.max_bytes_log_line
eps	.stats.captured.eps
f_total	.stats.flow.total
f_dropped	.stats.flow.dropped

Those keys are appended with the name of the instance running with _ between the instance name and instance metric key. So uptime for ids would be ids_uptime.

The default is named 'ids' unless otherwise specified via the extend.

There is a special instance name of .total which is the total of all the instances. So if you want the total eps, the metric would be .total_eps. Also worth noting that the alert value is the highest one found among all the instances.

SNMP Extend

Install the extend.

cpanm Sagan::Monitoring

Setup cron. Below is a example.

*/5 * * * * /usr/local/bin/sagan_stat_check > /dev/null

Configure snmpd.conf

extend sagan-stats /usr/bin/env PATH=/sbin:/bin:/usr/sbin:/usr/bin:/usr/local/sbin:/usr/local/bin sagan_stat_check -c

Restart snmpd on your system.

You will want to make sure that sagan is setup to with the values set below for stats-json processor, for a single instance setup..

enabled: yes
time: 300
subtract_old_values: true
filename: "$LOG_PATH/stats.json"

Any configuration of sagan_stat_check should be done in the cron setup. If the default does not work, check the docs for it at MetaCPAN for sagan_stat_check

Suricata

SNMP Extend

Install the extend.

cpanm Suricata::Monitoring

Setup cron. Below is a example.

*/5 * * * * /usr/local/bin/suricata_stat_check > /dev/null

Configure snmpd.conf

extend suricata-stats /usr/bin/env PATH=/sbin:/bin:/usr/sbin:/usr/bin:/usr/local/sbin:/usr/local/bin suricata_stat_check -c

Restart snmpd on your system.

You will want to make sure Suricata is set to output the stats to the eve file once a minute. This will help make sure that it won't be to far back in the file and will make sure it is recent when the cronjob runs.

Any configuration of suricata_stat_check should be done in the cron setup. If the default does not work, check the docs for it at MetaCPAN for suricata_stat_check

TinyDNS aka djbdns

Agent

Install the agent on this device if it isn't already and copy the tinydns script to /usr/lib/check_mk_agent/local/

Note: We assume that you use DJB's Daemontools to start/stop tinydns. And that your tinydns instance is located in /service/dns, adjust this path if necessary.

Replace your log's run file, typically located in /service/dns/log/run with:

#!/bin/sh
exec setuidgid dnslog tinystats ./main/tinystats/ multilog t n3 s250000 ./main/

Create tinystats directory and chown:

mkdir /service/dns/log/main/tinystats
chown dnslog:nofiles /service/dns/log/main/tinystats

Restart TinyDNS and Daemontools: /etc/init.d/svscan restart Note: Some say svc -t /service/dns is enough, on my install (Gentoo) it doesn't rehook the logging and I'm forced to restart it entirely.

Unbound

Unbound configuration:

# Enable extended statistics.
server:
        extended-statistics: yes
        statistics-cumulative: yes

remote-control:
        control-enable: yes
        control-interface: 127.0.0.1

Restart your unbound after changing the configuration, verify it is working by running unbound-control stats.

Option 1. SNMP Extend (Preferred and easiest method)

Copy the shell script, unbound, to the desired host

wget https://github.com/librenms/librenms-agent/raw/master/snmp/unbound -O /etc/snmp/unbound

Make the script executable

chmod +x /etc/snmp/unbound

Edit your snmpd.conf file and add:

extend unbound /usr/bin/sudo /etc/snmp/unbound

Restart snmpd.

The application should be auto-discovered as described at the top of the page. If it is not, please follow the steps set out under SNMP Extend heading top of page.

Option 2. Agent

Install the agent on this device if it isn't already and copy the unbound.sh script to /usr/lib/check_mk_agent/local/

UPS-nut

A small shell script that exports nut ups status.

SNMP Extend

Copy the shell script, unbound, to the desired host

wget https://github.com/librenms/librenms-agent/raw/master/snmp/ups-nut.sh -O /etc/snmp/ups-nut.sh

Make the script executable

chmod +x /etc/snmp/ups-nut.sh

Edit your snmpd.conf file (usually /etc/snmp/snmpd.conf) and add:

extend ups-nut /etc/snmp/ups-nut.sh

Restart snmpd on your host

The application should be auto-discovered as described at the top of the page. If it is not, please follow the steps set out under SNMP Extend heading top of page.

Optionally if you have multiple UPS or your UPS is not named APCUPS you can specify its name as an argument into /etc/snmp/ups-nut.sh

extend ups-nut /etc/snmp/ups-nut.sh ups1
extend ups-nut /etc/snmp/ups-nut.sh ups2

UPS-apcups

A small shell script that exports apcacess ups status.

SNMP Extend

Copy the shell script, unbound, to the desired host

wget https://github.com/librenms/librenms-agent/raw/master/snmp/ups-apcups -O /etc/snmp/ups-apcups

Make the script executable

chmod +x /etc/snmp/ups-apcups

Edit your snmpd.conf file (usually /etc/snmp/snmpd.conf) and add:

extend ups-apcups /etc/snmp/ups-apcups

If 'apcaccess' is not in the PATH enviromental variable snmpd is using, you may need to do something like below.

extend ups-apcups/usr/bin/env PATH=/sbin:/bin:/usr/sbin:/usr/bin:/usr/local/sbin:/usr/local/bin /etc/snmp/ups-apcups

Restart snmpd on your host

The application should be auto-discovered as described at the top of the page. If it is not, please follow the steps set out under SNMP Extend heading top of page.

Voip-monitor

Shell script that reports cpu-load/memory/open-files files stats of Voip Monitor

SNMP Extend

Download the script onto the desired host

wget https://raw.githubusercontent.com/librenms/librenms-agent/master/snmp/voipmon-stats.sh -O /etc/snmp/voipmon-stats.sh

Make the script executable

chmod +x /etc/snmp/voipmon-stats.sh

Edit your snmpd.conf file (usually /etc/snmp/voipmon-stats.sh) and add:

extend voipmon /etc/snmp/voipmon-stats.sh

ZFS

SNMP Extend

zfs-linux requires python3 >=python3.5.

The installation steps are:

Copy the polling script to the desired host (the host must be added to LibreNMS devices)
Make the script executable
Edit snmpd.conf to include ZFS stats

FreeBSD

wget https://github.com/librenms/librenms-agent/raw/master/snmp/zfs-freebsd -O /etc/snmp/zfs-freebsd
chmod +x /etc/snmp/zfs-freebsd
echo "extend zfs /etc/snmp/zfs-freebsd" >> /etc/snmp/snmpd.conf

Linux

wget https://github.com/librenms/librenms-agent/raw/master/snmp/zfs-linux -O /etc/snmp/zfs-linux
chmod +x /etc/snmp/zfs-linux
echo "extend zfs /usr/bin/sudo /etc/snmp/zfs-linux" >> /etc/snmp/snmpd.conf

Edit your sudo users (usually visudo) and add at the bottom:

snmp ALL=(ALL) NOPASSWD: /etc/snmp/zfs-linux

Now restart snmpd and you're all set.

Files

Applications.md

Latest commit

History

Applications.md

File metadata and controls

Applications

SNMP Extend

SUDO

Enable the application discovery module

Enable the application(s) to be discovered

Agent

Apache

SNMP Extend

Agent

Asterisk

SNMP Extend

backupninja

SNMP Extend

BIND9 aka named

SNMP Extend

Agent

Certificate

SNMP Extend

C.H.I.P

Docker Stats

SNMP Extend

Entropy

SNMP Extend

EXIM Stats

SNMP Extend

Fail2ban

SNMP Extend

FreeBSD NFS Client

SNMP Extend

FreeBSD NFS Server

SNMP Extend

FreeRADIUS

SNMP Extend

Agent

Freeswitch

Agent

SNMP Extend

GPSD

SNMP Extend

Agent

Icecast

SNMP Extend

ISC DHCP Stats

SNMP Extend

mailcow-dockerized postfix

SNMP Extend

Mailscanner

SNMP Extend

Mdadm

SNMP Extend

MegaRAID

Memcached

SNMP Extend

Munin

Agent

MySQL

Agent

SNMP extend

NGINX

SNMP Extend

Agent

NFS Server

SNMP Extend

NTP Client

SNMP Extend

NTP Server aka NTPD

SNMP Extend

Chronyd

SNMP Extend

Nvidia GPU

SNMP Extend

Opensearch\Elasticsearch

SNMP Extend

Open Grid Scheduler