/
FAQ
362 lines (245 loc) · 13.7 KB
/
FAQ
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
Questions:
1) I have an HCF modem. Can I use these drivers?
2) My modem's PCI ID is 127a:1025 or 127a:2005 and it doesn't work.
3) My dialer or Internet connection wizard does not find the modem, even though
no errors were reported during installation and /dev/ttySHSF0 exists.
4) I installed the driver, and now the /dev/ttySHSF0 or /dev/modem device is
supposed to be there but it doesn't exist.
5) The modem returns "NO DIALTONE" when I try to dial.
6) The modem works, but I can't hear anything when dialing.
7) What is a good initialization string to use with my modem?
8) The modem returns CONNECT messages with bogus connection speeds, like
"CONNECT 9600" or "CONNECT 115200".
9) Is the message about the kernel being tainted upon loading the modules
normal?
10) Changing serial port parameters with "setserial" on ttySHSF0 or /dev/modem
doesn't work.
11) I have an ACPI-based machine and the driver is crashing or not loading.
12) My modem doesn't work, or dials irregularly and sometimes it doesn't
transmit all the tones from the phone number.
13) The modem disconnects or the system crashes as soon as or shortly after I
start the graphical desktop (X, GNOME, KDE, etc..) or use the sound card.
14) My modem suddenly disconnects. What can potentially cause this?
15) rpm -i gives me this error: "Failed dependencies: pciutils is needed by ..."
16) hsfconfig gives me this error: "lspci: command not found"
17) How can I tell if my driver is working or not?
18) What should I do if my driver is not working?
19) Modules crash upon loading or refuse to load due to a wrong compiler
version.
20) Where does hsfconfig look for the kernel sources?
21) I'm having problems uninstalling the RPM package.
22) What does "warning: ...rpm: V3 DSA signature: NOKEY, key ID 5dfbf7dc" mean?
23) Is V.92 supported?
24) Is FAX supported?
25) Is VOICE supported?
26) Do you support other operating systems (eg. BeOS, FreeBSD, OpenBSD, etc.)?
27) Do you plan on releasing a Linux driver for Conexant ADSL chipsets?
Answers:
1) I have an HCF modem. Can I use these drivers?
No, these drivers are only for the Conexant HSF (softmodem)
family, not for the HCF (controllerless) chips.
HCF drivers are available from http://www.linuxant.com/drivers/hcf/
2) My modem's PCI ID is 127a:1025 or 127a:2005 and it doesn't work.
You probably should try both the HCF and HSF drivers, until
one works. Some early modems are incorrectly identified (HCF as HSF
and vice-versa) in some versions of the PCI ID lists used by lspci and
the linux kernel. Also, a few modem vendors have tried to save costs
by omitting the EEPROM where device IDs are stored, causing the same
default ID built into the bus interface chip to be used for both HCF
and HSF devices.
3) My dialer or Internet connection wizard does not find the modem, even though
no errors were reported during installation and /dev/ttySHSF0 exists.
You might want to try entering "/dev/modem" manually for the
modem device. Also, verify that "/dev/modem" is a symbolic link
pointing to ttySHSF0. If it is not the case, you can try
re-creating it with the command:
rm -f /dev/modem; ln -s ttySHSF0 /dev/modem
4) I installed the driver, and now the /dev/ttySHSF0 or /dev/modem device is
supposed to be there but it doesn't exist.
On devfs-based systems (such as Mandrake), the missing device node
is often a sign that the driver modules didn't load or initialize
properly. Try "modprobe /dev/ttySHSF", then check the /var/log/messages
file or run "dmesg" to see any kernel error messages that could provide
a clue as to why loading of the driver failed.
5) The modem returns "NO DIALTONE" when I try to dial.
Please verify your line cord and country settings
(with hsfconfig --country).
If they are correct and the "NO DIALTONE" problems persist, you
may try disabling dialtone detection with the "ATX3" command.
If this still doesn't work, there might be a more serious problem
with the machine, driver or its configuration. The cause might be ACPI
or APIC related (see FAQ items about these topics; try booting
with "acpi=off" and/or "noapic" kernel options) or incorrect
RELAYS or FLAGS definitions in the INF file for your modem.
You might want to try importing the original values for these
parameters from your modem's original Windows driver. If this
solves the problem or it persists, please tell us about it.
6) The modem works, but I can't hear anything when dialing.
Please verify the Ln and Mn settings with the AT&V command. They
should be L1 and M1.
If not, change them with the command: ATL1M1
If you still cannot hear any call progress sounds, and use a
modem model that does not have its own speaker (such as on a notebook),
verify your audio mixer settings (using aumix or equivalent utility) to
ensure that the volume levels are high enough and that the "PCM"
and "PhoneIn" channels are not muted.
With the HSF driver it is also possible to play call progress sounds
through the sound card. This requires that the system's audio driver be
properly configured. If other audio applications work but you still
cannot
hear call progress sounds, examine the /usr/sbin/hsfdcpd script.
7) What is a good initialization string to use with my modem?
The following initialization string, which resets the modem to factory
settings, should cover most situations:
AT &F
8) The modem returns CONNECT messages with bogus connection speeds, like
"CONNECT 9600" or "CONNECT 115200".
Use "ATW1" to enable reporting of line speed, error correction
protocol and DTE speed. See the command set reference manual
(100498D_RM_HxF_Released.pdf) for details.
9) Is the message about the kernel being tainted upon loading the modules
normal?
Yes, and it can be safely ignored.
10) Changing serial port parameters with "setserial" on ttySHSF0 or /dev/modem
doesn't work.
Since this modem driver provides a virtual serial interface, which
is not directly connected to a physical UART like a normal serial
port, it is not possible and would not make sense to configure
it with "setserial". Therefore you shouldn't use this command
on the ports associated with this driver.
11) I have an ACPI-based machine and the driver is crashing or not loading.
It might be necessary to recompile a generic kernel from
ftp.kernel.org with the latest ACPI (and perhaps also KACPID
kernel lost interrupt) patches from http://sf.net/projects/acpi/
Alternatively you could try the 2.6 development kernel, which has
better ACPI support. However we cannot guarantee that the drivers
will work with development kernels since they are constantly evolving.
12) My modem doesn't work, or dials irregularly and sometimes it doesn't
transmit all the tones from the phone number.
This problem might be ACPI-related or caused by a timing issue related
to the APIC timer module in some Linux kernels (usually SMP kernels).
You can verify if your kernel is using APIC by looking for the line
"ENABLING IO-APIC IRQs" when you run the "dmesg" command.
If you experience this problem, try disabling ACPI and/or
the APIC by booting your kernel with the option "acpi=off" and/or
the option "noapic".
13) The modem disconnects or the system crashes as soon as or shortly after I
start the graphical desktop (X, GNOME, KDE, etc..) or use the sound card.
Some users have reported conflicts between certain sound card drivers,
(especially AC97 devices) and our modem drivers. Most graphical
desktops access sound devices when starting up.
We are investigating these problems and are hoping to find solutions
soon. Meanwhile, we recommend disabling any conflicting modules while
you use the modem. If you experience a conflict, please report it.
14) My modem suddenly disconnects. What can potentially cause this?
An idle timer, bad connection, noise on the line,
call waiting, driver bug, incorrect NVM parameters,
overloaded system can all be potential causes for
sudden disconnections.
If you use the modem for an IP connection, try running a "ping"
in the background to keep the connection active.
If the problem persists, please send us detailed
information, including the output of
"cat /proc/driver/h*/0/lastcallstatus"
captured just after the connection was lost.
15) rpm -i gives me this error: "Failed dependencies: pciutils is needed by ..."
You need to install the pciutils package before installing the
driver. This package contains "lspci" which is used by hsfconfig
to detect your card.
pciutils should be installed from your Linux distribution CD. If
your distribution supports RPM, then the install command should be
similar to this: rpm -i /path/to/rpms/pciutils-....rpm
16) hsfconfig gives me this error: "lspci: command not found"
hsfconfig requires lspci to detect your card. lspci comes
with pciutils. We recommend that you install pciutils, but you can also
configure the device manually. hsfconfig will always fail if you
try to use the "-a" option without pciutils installed.
pciutils should be installed from your Linux distribution CD. If
your distribution supports RPM, then the install command should be
similar to this: rpm -i /path/to/rpms/pciutils-....rpm
17) How can I tell if my driver is working or not?
The easiest way to test your modem driver installation is to use a
terminal software like minicom. You should set the port to /dev/modem
or /dev/ttySHSF0. Once you have established a connection with the modem,
you can try to reset it by using the "ATZ" command. The modem should
answer "OK" to this command. Please refer to the
AT Command Set Reference Manual for the complete list of available
commands. You will find a link for the manual on our web site,
at the bottom of the driver's description section.
If you can communicate with the modem, then you should try to dial
a known valid number (eg. your ISP's number) with the command ATDT
followed by the phone number.
This procedure allows you to verify the driver's basic functionality
without involving a complex software like a PPP dialer.
18) What should I do if my driver is not working?
First, you should verify if the modules are loaded by the kernel with
the command "lsmod". You should see at least hsfengine and hsfserial.
If the modules do not appear, try to load them with "modprobe
/dev/ttySHSF". If you still don't see them with "lsmod", look at the
file /var/log/messages and the output from the command "dmesg" for
clues on why the modules failed to load.
19) Modules crash upon loading or refuse to load due to a wrong compiler
version.
It is very important that the driver modules be compiled with
the same compiler version that was used to build your kernel.
If the wrong version is used (i.e. gcc2 instead of gcc3 or vice-versa)
the system may crash or refuse to load the modules.
You can use the command "cat /proc/version" and "gcc -v" to
check the version strings.
20) Where does hsfconfig look for the kernel sources?
By default, hsfconfig looks for the symbolic link
/lib/modules/(kernelversion)/build
If this link exists and points to a valid directory, then
hsfconfig will use this directory as the kernel sources'
location.
If the link does not exist, hsfconfig will try to use
/usr/src/linux or /usr/local/src/linux.
Please note that if your kernel sources are in /usr/local/src/linux,
but you also have a /usr/src/linux link pointing to an invalid or empty
directory, then hsfconfig will try to use /usr/src/linux
and it will fail.
It is VERY important that the kernel sources' version match the kernel
version that you are currently running. If it isn't the case, then
hsfconfig will report and error.
21) I'm having problems uninstalling the RPM package.
Try the following command:
rpm -e --noscripts --force --allmatches hsfmodem
If the driver prevents your system from starting normally,
you could try booting in 'single user' or 'failsafe' mode first.
22) What does "warning: ...rpm: V3 DSA signature: NOKEY, key ID 5dfbf7dc" mean?
Before installing a package, RPM tries to verify its integrity.
The packages distributed by Linuxant are cryptographically
signed with our public PGP key, which is not known to RPM by
default. However, it can be found on many keyservers or downloaded from
http://www.linuxant.com/pubkey.asc
Once you have downloaded our public key, you can import it in your
RPM database. You can do this with the following command:
rpm --import /path/to/pubkey.asc
After the key has been imported, the NOKEY warning messages should
disappear.
Afterward, a package's signature can be verified with the command:
rpm --checksig /path/to/package.rpm
23) Is V.92 supported?
The V.92 modulation is supported as well as V.44 compression.
However, the MOH (Modem On Hold) feature cannot be supported at
this time because it requires a special application to interface
with the user. This should be provided in a future release.
24) Is FAX supported?
Both HCF and HSF drivers now have fax class 1 (+FCLASS=1) and 1.0
(+FCLASS=1.0)
support.
25) Is VOICE supported?
The HCF driver has voice support (+FCLASS=8), but this functionality
has not been tested a lot and might not work properly.
We hope to improve it and also add voice support to the HSF driver
soon.
26) Do you support other operating systems (eg. BeOS, FreeBSD, OpenBSD, etc.)?
At this time, we only distribute Linux drivers and there
are currently no plans to support other operating systems.
However, people interested in porting the drivers to other operating
systems should contact us.
27) Do you plan on releasing a Linux driver for Conexant ADSL chipsets?
Linuxant has licensed core technology and hopes to provide
official Linux drivers for Conexant ADSL chipsets in the future.
In the meantime, you could take a look at the "other drivers"
section on the links page at http://www.linuxant.com/drivers/links.php.