No IP show while emulating Tp-Link Archer AX50

[y198nt]

You can download the file at here: https://us.softpedia-secure-download.com/dl/68da52af83d3218977ededbd17bcf150/6613a902/301008453/drivers/router/Archer%20AX50(EU)_V1_210730.zip

When I run sudo python3 fat.py archer-ax53/ax50v1_intel-up-ver1-0-11-P1[20210730-rel54485]_signed.bin. First there is no IP for interaction

But after I pressed enter, it working normally. But it just there is no ip to interact
Starting firmware emulation... use Ctrl-a + x to exit
.
[ 0.000000] Linux version 2.6.39.4+ (ddcc@ddcc-virtual) (gcc version 5.3.0 (GCC) ) #2 Tue Sep 1 18:08:53 EDT 2020
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 00019300 (MIPS 24Kc)
[ 0.000000] FPU revision is: 00739300
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 00001000 @ 00000000 (reserved)
[ 0.000000] memory: 000ef000 @ 00001000 (ROM data)
[ 0.000000] memory: 00678000 @ 000f0000 (reserved)
[ 0.000000] memory: 0f897000 @ 00768000 (usable)
[ 0.000000] debug: ignoring loglevel setting.
[ 0.000000] Wasting 60672 bytes for tracking 1896 unused pages
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0x00000000 -> 0x00001000
[ 0.000000] Normal 0x00001000 -> 0x0000ffff
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x0000ffff
[ 0.000000] On node 0 totalpages: 65535
[ 0.000000] free_area_init_node: node 0, pgdat 80702800, node_mem_map 81000000
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 4064 pages, LIFO batch:0
[ 0.000000] Normal zone: 480 pages used for memmap
[ 0.000000] Normal zone: 60959 pages, LIFO batch:15
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65023
[ 0.000000] Kernel command line: root=/dev/sda1 console=ttyS0 nandsim.parts=64,64,64,64,64,64,64,64,64,64 rdinit=/firmadyne/preInit.sh rw debug ignore_loglevel print-fatal-signals=1 user_debug=31 firmadyne.syscall=0
[ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Primary instruction cache 2kB, VIPT, 2-way, linesize 16 bytes.
[ 0.000000] Primary data cache 2kB, 2-way, VIPT, no aliases, linesize 16 bytes
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 252264k/254556k available (4554k kernel code, 2292k reserved, 1609k data, 240k init, 0k highmem)
[ 0.000000] NR_IRQS:256
[ 0.000000] CPU frequency 333.33 MHz
[ 0.000000] Console: colour dummy device 80x25
[ 0.004000] Calibrating delay loop... 2662.40 BogoMIPS (lpj=5324800)
[ 0.032000] pid_max: default: 32768 minimum: 301
[ 0.036000] Mount-cache hash table entries: 512
[ 0.044000] Performance counters: No available PMU.
[ 0.052000] NET: Registered protocol family 16
[ 0.064000] bio: create slab at 0
[ 0.064000] vgaarb: loaded
[ 0.068000] SCSI subsystem initialized
[ 0.068000] libata version 3.00 loaded.
[ 0.072000] usbcore: registered new interface driver usbfs
[ 0.072000] usbcore: registered new interface driver hub
[ 0.072000] usbcore: registered new device driver usb
[ 0.076000] pci 0000:00:00.0: [11ab:4620] type 0 class 0x000600
[ 0.076000] pci 0000:00:00.0: reg 14: [mem 0x01000000-0x01ffffff pref]
[ 0.080000] pci 0000:00:0a.0: [8086:7110] type 0 class 0x000601
[ 0.080000] pci 0000:00:0a.1: [8086:7111] type 0 class 0x000101
[ 0.080000] pci 0000:00:0a.1: reg 20: [io 0x0000-0x000f]
[ 0.084000] pci 0000:00:0a.2: [8086:7112] type 0 class 0x000c03
[ 0.084000] pci 0000:00:0a.2: reg 20: [io 0x0000-0x001f]
[ 0.084000] pci 0000:00:0a.3: [8086:7113] type 0 class 0x000680
[ 0.088000] pci 0000:00:0a.3: address space collision: [io 0x1100-0x110f] conflicts with GT-64120 PCI I/O [io 0x1000-0x1fffff]
[ 0.088000] pci 0000:00:12.0: [1013:00b8] type 0 class 0x000300
[ 0.088000] pci 0000:00:12.0: reg 10: [mem 0x00000000-0x01ffffff pref]
[ 0.088000] pci 0000:00:12.0: reg 14: [mem 0x00000000-0x00000fff]
[ 0.088000] pci 0000:00:12.0: reg 30: [mem 0x00000000-0x0000ffff pref]
[ 0.088000] pci 0000:00:13.0: [8086:100e] type 0 class 0x000200
[ 0.088000] pci 0000:00:13.0: reg 10: [mem 0x00000000-0x0001ffff]
[ 0.088000] pci 0000:00:13.0: reg 14: [io 0x0000-0x003f]
[ 0.088000] pci 0000:00:13.0: reg 30: [mem 0x00000000-0x0007ffff pref]
[ 0.088000] pci 0000:00:14.0: [8086:100e] type 0 class 0x000200
[ 0.088000] pci 0000:00:14.0: reg 10: [mem 0x00000000-0x0001ffff]
[ 0.088000] pci 0000:00:14.0: reg 14: [io 0x0000-0x003f]
[ 0.092000] pci 0000:00:14.0: reg 30: [mem 0x00000000-0x0007ffff pref]
[ 0.092000] pci 0000:00:15.0: [8086:100e] type 0 class 0x000200
[ 0.092000] pci 0000:00:15.0: reg 10: [mem 0x00000000-0x0001ffff]
[ 0.096000] pci 0000:00:15.0: reg 14: [io 0x0000-0x003f]
[ 0.096000] pci 0000:00:15.0: reg 30: [mem 0x00000000-0x0007ffff pref]
[ 0.096000] vgaarb: device added: PCI:0000:00:12.0,decodes=io+mem,owns=none,locks=none
[ 0.096000] pci 0000:00:0a.3: BAR 8: [io 0x1100-0x110f] has bogus alignment
[ 0.100000] pci 0000:00:12.0: BAR 0: assigned [mem 0x10000000-0x11ffffff pref]
[ 0.100000] pci 0000:00:12.0: BAR 0: set to [mem 0x10000000-0x11ffffff pref] (PCI address [0x10000000-0x11ffffff])
[ 0.100000] pci 0000:00:13.0: BAR 6: assigned [mem 0x12000000-0x1207ffff pref]
[ 0.100000] pci 0000:00:14.0: BAR 6: assigned [mem 0x12080000-0x120fffff pref]
[ 0.100000] pci 0000:00:15.0: BAR 6: assigned [mem 0x12100000-0x1217ffff pref]
[ 0.100000] pci 0000:00:13.0: BAR 0: assigned [mem 0x12180000-0x1219ffff]
[ 0.100000] pci 0000:00:13.0: BAR 0: set to [mem 0x12180000-0x1219ffff] (PCI address [0x12180000-0x1219ffff])
[ 0.100000] pci 0000:00:14.0: BAR 0: assigned [mem 0x121a0000-0x121bffff]
[ 0.100000] pci 0000:00:14.0: BAR 0: set to [mem 0x121a0000-0x121bffff] (PCI address [0x121a0000-0x121bffff])
[ 0.100000] pci 0000:00:15.0: BAR 0: assigned [mem 0x121c0000-0x121dffff]
[ 0.100000] pci 0000:00:15.0: BAR 0: set to [mem 0x121c0000-0x121dffff] (PCI address [0x121c0000-0x121dffff])
[ 0.100000] pci 0000:00:12.0: BAR 6: assigned [mem 0x121e0000-0x121effff pref]
[ 0.100000] pci 0000:00:12.0: BAR 1: assigned [mem 0x121f0000-0x121f0fff]
[ 0.100000] pci 0000:00:12.0: BAR 1: set to [mem 0x121f0000-0x121f0fff] (PCI address [0x121f0000-0x121f0fff])
[ 0.100000] pci 0000:00:13.0: BAR 1: assigned [io 0x1000-0x103f]
[ 0.104000] pci 0000:00:13.0: BAR 1: set to [io 0x1000-0x103f] (PCI address [0x1000-0x103f])
[ 0.104000] pci 0000:00:14.0: BAR 1: assigned [io 0x1040-0x107f]
[ 0.104000] pci 0000:00:14.0: BAR 1: set to [io 0x1040-0x107f] (PCI address [0x1040-0x107f])
[ 0.104000] pci 0000:00:15.0: BAR 1: assigned [io 0x1080-0x10bf]
[ 0.104000] pci 0000:00:15.0: BAR 1: set to [io 0x1080-0x10bf] (PCI address [0x1080-0x10bf])
[ 0.104000] pci 0000:00:0a.2: BAR 4: assigned [io 0x10c0-0x10df]
[ 0.104000] pci 0000:00:0a.2: BAR 4: set to [io 0x10c0-0x10df] (PCI address [0x10c0-0x10df])
[ 0.104000] pci 0000:00:0a.1: BAR 4: assigned [io 0x10e0-0x10ef]
[ 0.104000] pci 0000:00:0a.1: BAR 4: set to [io 0x10e0-0x10ef] (PCI address [0x10e0-0x10ef])
[ 0.112000] Switching to clocksource MIPS
[ 0.116000] Switched to NOHz mode on CPU #0
[ 0.116000] NET: Registered protocol family 2
[ 0.116000] IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.120000] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.120000] TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.120000] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.124000] TCP reno registered
[ 0.124000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.124000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.124000] NET: Registered protocol family 1
[ 0.124000] PCI: CLS 0 bytes, default 64
[ 0.176000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.176000] Registering unionfs 2.6 (for 2.6.39.4)
[ 0.176000] JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[ 0.176000] ROMFS MTD (C) 2007 Red Hat, Inc.
[ 0.176000] msgmni has been set to 492
[ 0.184000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 0.184000] io scheduler noop registered
[ 0.184000] io scheduler cfq registered (default)
[ 0.184000] firmadyne: devfs: 1, execute: 1, procfs: 1, syscall: 0
[ 0.184000] firmadyne: Cannot register character device: watchdog, 0xa, 0x82!
[ 0.184000] firmadyne: Cannot register character device: wdt, 0xfd, 0x0!
[ 0.216000] PCI: Enabling device 0000:00:12.0 (0000 -> 0002)
[ 0.220000] cirrusfb 0000:00:12.0: Cirrus Logic chipset on PCI bus, RAM (4096 kB) at 0x10000000
[ 0.424000] Console: switching to colour frame buffer device 80x30
[ 0.436000] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 0.460000] serial8250.0: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 0.464000] console [ttyS0] enabled, bootconsole disabled
[ 0.464000] console [ttyS0] enabled, bootconsole disabled
[ 0.484000] serial8250.0: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 0.492000] brd: module loaded
[ 0.492000] loop: module loaded
[ 0.496000] ata_piix 0000:00:0a.1: version 2.13
[ 0.496000] PCI: Enabling device 0000:00:0a.1 (0000 -> 0001)
[ 0.496000] PCI: Setting latency timer of device 0000:00:0a.1 to 64
[ 0.504000] scsi0 : ata_piix
[ 0.508000] scsi1 : ata_piix
[ 0.508000] ata1: PATA max UDMA/33 cmd 0x1f0 ctl 0x3f6 bmdma 0x10e0 irq 14
[ 0.508000] ata2: PATA max UDMA/33 cmd 0x170 ctl 0x376 bmdma 0x10e8 irq 15
[ 0.516000] [nandsim] warning: read_byte: unexpected data output cycle, state is STATE_READY return 0x0
[ 0.516000] [nandsim] warning: read_byte: unexpected data output cycle, state is STATE_READY return 0x0
[ 0.516000] [nandsim] warning: read_byte: unexpected data output cycle, state is STATE_READY return 0x0
[ 0.516000] [nandsim] warning: read_byte: unexpected data output cycle, state is STATE_READY return 0x0
[ 0.516000] [nandsim] warning: read_byte: unexpected data output cycle, state is STATE_READY return 0x0
[ 0.516000] [nandsim] warning: read_byte: unexpected data output cycle, state is STATE_READY return 0x0
[ 0.520000] NAND device: Manufacturer ID: 0x98, Chip ID: 0x39 (Toshiba NAND 128MiB 1,8V 8-bit)
[ 0.520000] flash size: 128 MiB
[ 0.520000] page size: 512 bytes
[ 0.520000] OOB area size: 16 bytes
[ 0.520000] sector size: 16 KiB
[ 0.520000] pages number: 262144
[ 0.520000] pages per sector: 32
[ 0.520000] bus width: 8
[ 0.520000] bits in sector size: 14
[ 0.520000] bits in page size: 9
[ 0.520000] bits in OOB size: 4
[ 0.520000] flash size with OOB: 135168 KiB
[ 0.520000] page address bytes: 4
[ 0.520000] sector address bytes: 3
[ 0.520000] options: 0x62
[ 0.524000] Scanning device for bad blocks
[ 0.564000] Creating 11 MTD partitions on "NAND 128MiB 1,8V 8-bit":
[ 0.564000] 0x000000000000-0x000000100000 : "NAND simulator partition 0"
[ 0.568000] 0x000000100000-0x000000200000 : "NAND simulator partition 1"
[ 0.568000] 0x000000200000-0x000000300000 : "NAND simulator partition 2"
[ 0.572000] 0x000000300000-0x000000400000 : "NAND simulator partition 3"
[ 0.572000] 0x000000400000-0x000000500000 : "NAND simulator partition 4"
[ 0.572000] 0x000000500000-0x000000600000 : "NAND simulator partition 5"
[ 0.572000] 0x000000600000-0x000000700000 : "NAND simulator partition 6"
[ 0.572000] 0x000000700000-0x000000800000 : "NAND simulator partition 7"
[ 0.572000] 0x000000800000-0x000000900000 : "NAND simulator partition 8"
[ 0.576000] 0x000000900000-0x000000a00000 : "NAND simulator partition 9"
[ 0.576000] 0x000000a00000-0x000008000000 : "NAND simulator partition 10"
[ 0.576000] e1000: Intel(R) PRO/1000 Network Driver - version 7.3.21-k8-NAPI
[ 0.576000] e1000: Copyright (c) 1999-2006 Intel Corporation.
[ 0.576000] PCI: Enabling device 0000:00:13.0 (0000 -> 0003)
[ 0.576000] PCI: Setting latency timer of device 0000:00:13.0 to 64
[ 0.580000] cfg80211: Calling CRDA to update world regulatory domain
[ 0.816000] ata2.01: NODEV after polling detection
[ 0.816000] ata1.01: NODEV after polling detection
[ 0.816000] ata2.00: ATAPI: QEMU DVD-ROM, 2.5+, max UDMA/100
[ 0.820000] ata1.00: ATA-7: QEMU HARDDISK, 2.5+, max UDMA/100
[ 0.820000] ata1.00: 524288 sectors, multi 16: LBA48
[ 0.820000] ata1.00: configured for UDMA/33
[ 0.828000] ata2.00: configured for UDMA/33
[ 0.832000] scsi 0:0:0:0: Direct-Access ATA QEMU HARDDISK 2.5+ PQ: 0 ANSI: 5
[ 0.836000] sd 0:0:0:0: [sda] 524288 512-byte logical blocks: (268 MB/256 MiB)
[ 0.836000] sd 0:0:0:0: [sda] Write Protect is off
[ 0.836000] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 0.836000] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 0.852000] e1000 0000:00:13.0: eth0: (PCI:33MHz:32-bit) 52:54:00:12:34:56
[ 0.852000] e1000 0000:00:13.0: eth0: Intel(R) PRO/1000 Network Connection
[ 0.852000] PCI: Enabling device 0000:00:14.0 (0000 -> 0003)
[ 0.852000] PCI: Setting latency timer of device 0000:00:14.0 to 64
[ 0.860000] sda: sda1
[ 0.868000] sd 0:0:0:0: [sda] Attached SCSI disk
[ 0.872000] scsi 1:0:0:0: CD-ROM QEMU QEMU DVD-ROM 2.5+ PQ: 0 ANSI: 5
[ 1.128000] e1000 0000:00:14.0: eth1: (PCI:33MHz:32-bit) 52:54:00:12:34:57
[ 1.128000] e1000 0000:00:14.0: eth1: Intel(R) PRO/1000 Network Connection
[ 1.128000] PCI: Enabling device 0000:00:15.0 (0000 -> 0003)
[ 1.128000] PCI: Setting latency timer of device 0000:00:15.0 to 64
[ 1.388000] e1000 0000:00:15.0: eth2: (PCI:33MHz:32-bit) 52:54:00:12:34:58
[ 1.404000] e1000 0000:00:15.0: eth2: Intel(R) PRO/1000 Network Connection
[ 1.416000] e1000e: Intel(R) PRO/1000 Network Driver - 1.3.10-k2
[ 1.424000] e1000e: Copyright(c) 1999 - 2011 Intel Corporation.
[ 1.432000] pcnet32: pcnet32.c:v1.35 21.Apr.2008 tsbogend@alpha.franken.de
[ 1.444000] PPP generic driver version 2.4.2
[ 1.448000] PPP Deflate Compression module registered
[ 1.460000] PPP MPPE Compression module registered
[ 1.464000] NET: Registered protocol family 24
[ 1.464000] tun: Universal TUN/TAP device driver, 1.6
[ 1.468000] tun: (C) 1999-2004 Max Krasnyansky maxk@qualcomm.com
[ 1.472000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.476000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 1.476000] uhci_hcd: USB Universal Host Controller Interface driver
[ 1.480000] PCI: Enabling device 0000:00:0a.2 (0000 -> 0001)
[ 1.480000] PCI: Setting latency timer of device 0000:00:0a.2 to 64
[ 1.480000] uhci_hcd 0000:00:0a.2: UHCI Host Controller
[ 1.484000] uhci_hcd 0000:00:0a.2: new USB bus registered, assigned bus number 1
[ 1.484000] uhci_hcd 0000:00:0a.2: irq 11, io base 0x000010c0
[ 1.488000] hub 1-0:1.0: USB hub found
[ 1.488000] hub 1-0:1.0: 2 ports detected
[ 1.492000] Initializing USB Mass Storage driver...
[ 1.492000] usbcore: registered new interface driver usb-storage
[ 1.492000] USB Mass Storage support registered.
[ 1.496000] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 1.496000] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 1.496000] mousedev: PS/2 mouse device common for all mice
[ 1.500000] rtc_cmos rtc_cmos: rtc core: registered rtc_cmos as rtc0
[ 1.500000] rtc0: alarms up to one day, 242 bytes nvram
[ 1.504000] i2c /dev entries driver
[ 1.504000] piix4_smbus 0000:00:0a.3: SMBus Host Controller at 0x1100, revision 0
[ 1.504000] sdhci: Secure Digital Host Controller Interface driver
[ 1.504000] sdhci: Copyright(c) Pierre Ossman
[ 1.504000] usbcore: registered new interface driver usbhid
[ 1.504000] usbhid: USB HID core driver
[ 1.508000] Netfilter messages via NETLINK v0.30.
[ 1.508000] nf_conntrack version 0.5.0 (3941 buckets, 15764 max)
[ 1.508000] ctnetlink v0.93: registering with nfnetlink.
[ 1.512000] IPv4 over IPv4 tunneling driver
[ 1.512000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 1.516000] arp_tables: (C) 2002 David S. Miller
[ 1.520000] TCP cubic registered
[ 1.520000] Initializing XFRM netlink socket
[ 1.520000] NET: Registered protocol family 10
[ 1.528000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 1.528000] IPv6 over IPv4 tunneling driver
[ 1.532000] NET: Registered protocol family 17
[ 1.532000] Bridge firewalling registered
[ 1.536000] Ebtables v2.0 registered
[ 1.536000] 802.1Q VLAN Support v1.8 Ben Greear greearb@candelatech.com
[ 1.536000] All bugs added by David S. Miller davem@redhat.com
[ 1.536000] lib80211: common routines for IEEE802.11 drivers
[ 1.536000] lib80211_crypt: registered algorithm 'NULL'
[ 1.540000] rtc_cmos rtc_cmos: setting system clock to 2024-04-08 08:17:00 UTC (1712564220)
[ 1.568000] EXT2-fs (sda1): warning: mounting unchecked fs, running e2fsck is recommended
[ 1.568000] VFS: Mounted root (ext2 filesystem) on device 8:1.
[ 1.572000] Freeing prom memory: 956k freed
[ 1.612000] Freeing unused kernel memory: 240k freed
[ 1.660000] input: AT Raw Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
[ 1.680000] firmadyne: sys_reboot[PID: 1 (init)]: magic1:fee1dead, magic2:28121969, cmd:0
[ 1.688000] EXT2-fs (sda1): error: ext2_lookup: deleted inode referenced: 464
[ 1.692000] EXT2-fs (sda1): error: ext2_lookup: deleted inode referenced: 464
init started: BusyBox v1.19.4 (2021-07-23 15:51:06 CST)
[ 1.712000] EXT2-fs (sda1): error: ext2_lookup: deleted inode referenced: 464
[ 1.712000] EXT2-fs (sda1): error: ext2_lookup: deleted inode referenced: 464
[ 1.776000] EXT2-fs (sda1): error: ext2_lookup: deleted inode referenced: 35225
[ 1.796000] firmadyne: do_execve: /firmadyne/console
[ 1.800000] OFFSETS: offset of pid: 0xc4 offset of comm: 0x1a4
[ 1.864000] input: ImExPS/2 Generic Explorer Mouse as /devices/platform/i8042/serio1/input/input1
[ 1.936000] EXT2-fs (sda1): error: ext2_lookup: deleted inode referenced: 464
[ 1.936000] EXT2-fs (sda1): error: ext2_lookup: deleted inode referenced: 464
[ 1.960000] EXT2-fs (sda1): error: ext2_lookup: deleted inode referenced: 464
[ 1.964000] EXT2-fs (sda1): error: ext2_lookup: deleted inode referenced: 464
sysinit: cat: can't open '/proc/cmdline': No such file or directory
[ 2.088000] EXT2-fs (sda1): error: ext2_lookup: deleted inode referenced: 464
[ 2.088000] EXT2-fs (sda1): error: ext2_lookup: deleted inode referenced: 464
sysinit: sysctl: chdir(/proc/sys): No such file or directory
[ 2.112000] EXT2-fs (sda1): error: ext2_lookup: deleted inode referenced: 464
[ 2.112000] EXT2-fs (sda1): error: ext2_lookup: deleted inode referenced: 464
sysinit: sysctl: chdir(/proc/sys): No such file or directory
[ 2.132000] EXT2-fs (sda1): error: ext2_lookup: deleted inode referenced: 464
[ 2.132000] EXT2-fs (sda1): error: ext2_lookup: deleted inode referenced: 464
sysinit: sysctl: chdir(/proc/sys): No such file or directory
[ 2.152000] EXT2-fs (sda1): error: ext2_lookup: deleted inode referenced: 464
[ 2.152000] EXT2-fs (sda1): error: ext2_lookup: deleted inode referenced: 464
sysinit: sysctl: chdir(/proc/sys): No such file or directory
[ 2.172000] EXT2-fs (sda1): error: ext2_lookup: deleted inode referenced: 464
[ 2.172000] EXT2-fs (sda1): error: ext2_lookup: deleted inode referenced: 464
sysinit: sysctl: chdir(/proc/sys): No such file or directory
[ 2.192000] EXT2-fs (sda1): error: ext2_lookup: deleted inode referenced: 464
[ 2.192000] EXT2-fs (sda1): error: ext2_lookup: deleted inode referenced: 464
sysinit: sysctl: chdir(/proc/sys): No such file or directory
[ 2.208000] EXT2-fs (sda1): error: ext2_lookup: deleted inode referenced: 464
[ 2.212000] EXT2-fs (sda1): error: ext2_lookup: deleted inode referenced: 464
sysinit: sysctl: chdir(/proc/sys): No such file or directory
QEMU: Terminated

[extremecoders-re]

Try increasing the timeout to 120 seconds in inferNetwork.sh

https://github.com/firmadyne/firmadyne/blob/748fdec9a8eb716fbb9598404389211aed8c987a/scripts/inferNetwork.sh#L40

[y198nt]

qemu.final.serial.log

it still error although i raise the time up to 180,
sudo python3 fat.py archer-ax53/_ax50v1_intel-up-ver1-0-11-P1[20210730-rel54485]_signed.bin.extracted/0x460AA/460AA.squashfs

                           __           _
                          / _|         | |
                         | |_    __ _  | |_
                         |  _|  / _` | | __|
                         | |   | (_| | | |_
                         |_|    \__,_|  \__|

            Welcome to the Firmware Analysis Toolkit - v0.3
Offensive IoT Exploitation Training http://bit.do/offensiveiotexploitation
              By Attify - https://attify.com  | @attifyme

[+] Firmware: 460AA.squashfs
[+] Extracting the firmware...
[+] Image ID: 2
[+] Identifying architecture...
[+] Architecture: mipseb
[+] Building QEMU disk image...
[+] Setting up the network connection, please standby...
[+] Network interfaces: []
[+] All set! Press ENTER to run the firmware...
[+] When running, press Ctrl + A X to terminate qemu
[+] Command line: /home/gh0st/firmware-analysis-toolkit/firmadyne/scratch/
2/run.sh
Starting firmware emulation... use Ctrl-a + x to exit