/
README
81 lines (75 loc) · 4.67 KB
/
README
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
externals_2017.f
-Program to calculate measured cross sections
-Input files
--input/cross-sec-data/*: cross section data for fits & interpolations
--input/d2model/parms.dat: parameters for d2model
--input/externals/externals.inp: list of i/o files which are fed into externals_2017.f
--input/grids/*.inp: Input kinematics file listing variables: E0, Ep, theta, W2, Q2
--input/targets/*.targ: Contains target & input parameters for the externals code
-Output files:
--output/externals/externals.out: Output file from externals code with radiative corrections
--output/externals/*.out: Output file from externals code with diagnostics information
externals.inp
-List of i/o files which are fed into externals_2017.f
-The first line is a comment
-Dependent files:
--eg1b.inp (second line)
---EXTERNAL_RUNPLAN (UNIT=7)
---Input kinematics file listing variables: E0, Ep, theta, W2, Q2 -> make_grid.C prints these
---Code assumes that first six lines of file are comments. This reading is done in
subroutine READIN_EXT
---Only E0, Ep, and theta are read in by the externals code, W2 and Q2
are supplemental information for the user
--eg1b.targ (third line)
---EXTERNAL_TARGET (UNIT=5)
---Contains input parameters for the externals code
---Has a very specific format read (see subroutine READIN_EXT) so must be careful about format
---First 3 line read into COMMENT array then skips a line
---5th and 6th lines read in IA and IZ with format 15x,i5 then skips a line
----IA and IZ are the atomic number and charge of target.
---8th and 9th lines read in AVGA and AVGM with format 15x,f14.8 then skips a line
----If AVGA and AVGM are zero then calculated in subroutine weiz. For A>4 uses
the Weisacker mass formula.
---11th line reads in TARGET with format 20x,A7 then skips a line
----TARGET is used for specific experiments hardwired in the code to set the target
radiation lengths in subroutine RADIATORS. If set to "readin" ( or any name
that is not hadrcoded in subroutine RADIATORS) , the radiation
lengths are set from input ttarg,twall,tbeam,tspec
Also the variable SMRDEP is set differently from default for certain experiments.
---13th-16th line reads in ttarg,twall,tbeam,tspec with format 15x,f14.8
---17th lines reads NSEG with format 15x,i5 then skips 2 lines
----NSEG sets number of segments for the SIMPSON rule integration. Nseg must be EVEN.
---20th line reads IG with format 15x,i5 then skips a line
----IG selects the elastic proton form factor model
in subroutine NFORM ( see NFORM for list)
IG=15 use Bosted fit. Should be updated with more recent parametrizations.
---22nd line reads IDUT with format 15x,i5
----IDUT selects the elastic deuteron form factor model in subroutine NUC_FORM_FACTOR
---23nd line reads INEL_MODEL with format 15x,i5
----INEL_MODEL selects inelastic cross section model in INELAST.
INEL_MODEL = 4 selects F1F209 . Best option. Many older models available.
---24th line reads PAULI_MODEL with format 15x,i5
----PAULI_MODEL sets model in subroutine PAULI_SUPPRESSION.
0 = old stein model; 1 = tsai model; 2 no suppression
F1F2QE09 uses Pauli suppression model from Tsai RMP 46,816(74) eq.B54
---25th line reads NUC_METHOD with format 15x,i5
----UC_METHOD 0=No cos(theta_k) integration; 1= cos(th_k) integration
---26th line reads NUC_MODEL with format 15x,i5
----NUC_MODEL not used if INEL_MODEL=4.
--output/externals/*.out (fourth line)
---EXTERNAL_OUT (UNIT=10)
---Output file from externals code with diagnostics information.
---Has the table of kinematics and radiatied cross sections.
---Contains the following variables: beam energy, scattered electron energy,
scattered electron angle, x, q2, SIGMA_BORN+SIGMA_CORR,
sigma_qela(2) + sigma_elpk(2) + sigma_inel(2), sigma_elpk(2), sigma_qela(2), sigma_inel(2),
SIGMA_BORN, iesv, iqsv, iwsv, sigma_qela(1) + sigma_elpk(1) + sigma_inel(1), sigma_elastic
---Note: the variables iesv, iqsv, iwsv are filled when doeg1b flag is set to true
make_grid.C
-Defines the grid for rad-corr, writes an input file (*.inp) containing the
variables: E0, E, theta, W2, Q2 based on energy steps in scattered beam energy and angle
-The produced input file is read by the externals_2017.f script
make_rc_dat.C
-Converts the output from extern.out in to the *.dat format that is required for the
Monte-Carlo re-weighting code
Flow: ./run_externals.sh -> ./make_grid -> ./externals_2017 -> ./make_rc_dat