/
DroneBridgeConfig.ini
executable file
·204 lines (180 loc) · 8.75 KB
/
DroneBridgeConfig.ini
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
[COMMON]
# ---------------------------------------------------------------
# This section is used configure common settings of DroneBridge ground and UAV
# ---------------------------------------------------------------
# Frequency of the long range link (see supported frequencies at the bottom of this document)
freq=2437
# CTS protection (use in areas with other wifi networks)
# set to "auto" for automatic detection, "N" to disable, "Y" to enable
cts_protection=auto
# choose a random number. Allowed numbers: 0-255
# has to be the same on drone and groundstation! Acts as a identifier for both and the link.
communication_id=200
# FEC parameters for video module
video_blocks=8
video_fecs=4
video_blocklength=1024
# Video FPS - Choose between 30, 40, 48, 59.9
fps=48
# Uncomment to blacklist a network interface from being changed. Useful if using RPi ZeroW in headless mode and need internal wifi to remain unchanged
# Set to 'wlan0' for RPi Zero/Pi3 or MAC address of adapter to ignore
# blacklist_ap=wlan0
# Compatibility mode for sending operations so that DroneBridge protocol can be received & decoded by non patched network drivers
# Use with Ubuntu etc. as receiving OS. Set to 1 to enable. Set to 0 to disable
compatibility_mode=0
[GROUND]
# ---------------------------------------------------------------
# This section is used configure DroneBridge on the ground station side
# ---------------------------------------------------------------
# ------- RADIO LINK SETTINGS -------
# -----------------------------------
# Fixed data rate for Atheros cards - with Ralink cards the data rate is set individually for each module (automatically)
# Lower settings yield higher range and vice versa.
# Bitrate in Mbps. Options: 1|2|5|6|9|11|12|18|24|36|48|54
datarate=2
# Manually set the frequency of specified wifi adapters [Y|N]
freq_ovr=N
# When freq_ovr=Y - Define the adapter and its frequency that it should use
nic_1=24050f73b574
frq_1=2472
nic_2=24050f73b574
frq_2=2472
nic_3=24050f73b574
frq_3=2472
nic_4=24050f73b574
frq_4=2472
# [auto|manual] Use "auto" if only one wifi stick is connected! We will choose that one for all DB-modules
interface_selection=auto
# If interface_selection=manual
# Interfaces which DroneBridge modules use to communicate with groundstation (manual mode)
# Type in the MAC address of the desired wifi card without the ":"
interface_control=24050f73b574
interface_tel=24050f73b574
interface_video=24050f73b574
interface_comm=24050f73b574
interface_proxy=24050f73b574
# ------- ACTIVATE MODULES -------
# --------------------------------
# enable "Y" or disable "N" DroneBridge modules
en_control=Y
en_video=Y
en_comm=Y
en_plugin=N
# [1|2|5] 1: MSP v1, 2: MSP v2, 5: DroneBridge RC protocol (recommended)
rc_proto=5
# Allow or prevent [Y|N] overwrite of RC values sent via DroneBridge control module (used by head trackers etc.)
en_rc_overwrite=N
# Number of Joystick interface for RC (/dev/input/js0 -> 0)
joy_interface=0
# set this to "Y" to enable Wifi Hotspot. Default SSID is "DroneBridge", password is "dronebridge".
# See apconfig.txt for configuration. This will forward the received video and telemetry streams to a
# smartphone/tablet or computer connected to the RX Pi via WiFi.
wifi_ap=N
#
# Set to "internal" to use the interal Pi3 wifi chip or the MAC address of the USB wifi card you want to use
wifi_ap_if=internal
# set this to "Y" to enable Ethernet hotspot. This will forward the received video and telemetry streams
# to another computer or other device connected to the Raspberry via Ethernet
eth_hotspot=N
# Set this to "raw" to forward a raw h264 stream to 2nd display devices (for FPV_VR app)
# Set to "rtp" to forward RTP h264 stream (for Tower app and gstreamer etc.)
# NOTE: IN THIS RELEASE ONLY RAW FORWARD IS SUPPORTED!
fwd_stream=raw
# UDP port to send video stream to, set to 5000 for FPV_VR/DroneBridge app or 5600 for Mission Planner
fwd_stream_port=5000
[AIR]
# ---------------------------------------------------------------
# This section is used configure DroneBridge on the UAV side
# ---------------------------------------------------------------
# ------- RADIO LINK SETTINGS -------
# -----------------------------------
# Fixed data rate for Atheros cards - with Ralink cards the data rate is set individually for each module (automatically)
# Lower settings yield higher range and vice versa. Options: 1|2|5|6|9|11|12|18|24|36|48|54
# Bitrate in Mbps
datarate=18
# Manually set the frequency of specified wifi adapters [Y|N]
freq_ovr=N
# When freq_ovr=Y - Define the adapter and its frequency that it should use
nic_1=24050f73b574
frq_1=2472
nic_2=24050f73b574
frq_2=2472
# [auto|manual] Use "auto" if only one wifi stick is connected! We will choose that one for all DB-modules
interface_selection=auto
# If interface_selection=manual
# Interfaces which DroneBridge modules use to communicate with groundstation (manual mode)
interface_control=18a6f716a511
interface_tel=18a6f716a511
interface_video=18a6f716a511
interface_comm=18a6f716a511
# ------- ACTIVATE MODULES -------
# --------------------------------
# enable "Y" or disable "N" DroneBridge modules
en_tel=Y
en_video=Y
en_comm=Y
en_control=Y
en_plugin=N
# ------- VIDEO MODULE UAV (WBC) -------
# --------------------------------------
# Set additional raspivid parameters here
extraparams=-cd H264 -n -fl -ih -pf high -ex sports -mm average -awb horizon
# Lower values mean faster glitch-recovery, but also lower video quality.
# With fps=48 and keyframerate=5, glitches will stay visible for around 100ms in worst case.
# You can set this higher or lower according to your needs. Minimum value is 2.
keyframerate=5
# Camera settings: https://www.raspberrypi.org/documentation/raspbian/applications/camera.md
# V1 cam: 640x480: 48fps, 59.9fps, 1296x730: 30fps, 48fps. 1920x1080: 30fps
# V2 cam: 640x480: 48fps, 59.9fps, 1280x720: 30fps, 48fps, 59.9fps. 1640x922: 30fps, 40fps. 1920x1080: 30fps
width=1280
height=720
# set to "auto" for automatic video bitrate measuring. Set to a fixed value in [kBit/s] to disable automatic measuring
# ! AUTO DOES NOT WORK PROPERLY IN ALPHA RELEASE !
video_bitrate=5500
# if video_bitrate above is set to "auto" the video bitrate will be determined
# by measuring the available bitrate and multiplying it with BITRATE_PERCENT
# Depending on channel utilization by other wifi networks you may need to set
# this to a lower value like 60% to avoid a delayed video stream.
# On free channels you may set this to a higher value like 75% to get a higher
# bitrate and thus image quality.
video_channel_util=65
# Enable video recorder on the UAV side
en_video_rec=N
# Path to the directory where video files will be stored.
video_mem=/DroneBridge/recordings
# ------- CONTROL MODULE UAV -------
# ------------------------------------
# Serial interface used by control module (MSP/MAVLink up/downlink)
# set to /dev/serial1 if you connect via USB-VCP | set to /dev/serial0 if you use Pis UART
serial_int_cont=/dev/serial0
# Serial baud rate set on <serial_int_cont>
# Options are: 2400, 4800, 9600, 19200, 38400, 57600, 115200
baud_control=115200
# Serial protocol used (by control module) to send RC commands (MSP only) and
# to communicate with FC in general (settings, missions etc.)
# 1=MSPv1, 2=MSPv2 [iNAV], 3=MAVLink v1, 4=MAVLink v2, 5=MAVLink transparent pass through [recommended for MAVLink]
serial_prot=5
# Over the air long range packet size when serial_prot=5; should be a value of 2^n (n=1,2,3,...)
pass_through_packet_size=128
# MAVLink RC messages are not supported, but you can use SUMD RC instead. You will need an extra serial
# port for this. FTDI adapters can solve that issue. If SUMD is deactivated and serial_prot is MSP the RC
# messages will be sent via MSP (SET_RAW_RC)
# [Y|N] [!experimental!]
enable_sumd_rc=N
serial_int_sumd=/dev/ttyUSB0
[MYCUSTOMSECTION]
# Add as many sections as you like to this file. You can e.g. store the settings for your plugin right inside this conig file.
# To change/request these settings you can use the communication protocol. Just set the keys and section right.
plugin_1_setting=45
# the following frequencies are supported:
# 2412, 2417, 2422, 2427, 2432, 2437, 2442, 2447, 2452, 2457, 2462, 2467, 2472, 2484 (Ralink and Atheros)
# 2312, 2317, 2322, 2327, 2332, 2337, 2342, 2347, 2352, 2357, 2362, 2367, 2372, 2377, 2382, 2387, 2392, 2397, 2402, 2407 (Atheros only)
# 2477, 2482, 2487, 2489, 2492, 2494, 2497, 2499, 2512, 2532, 2572, 2592, 2612, 2632, 2652, 2672, 2692, 2712 (Atheros only)
#
# 5180, 5200, 5220, 5240, 5260, 5280, 5300, 5320
# 5500, 5520, 5540, 5560, 5580, 5600, 5620, 5640, 5660, 5680, 5700
# 5745, 5765, 5785, 5805, 5825
#
# 2.3Ghz and 2.5-2.7Ghz band only works with Atheros cards. Check your local regulations before transmitting!
# Frequencies higher than 2512MHz work with Atheros, but with a lot lower transmit power and sensitivity and
# thus greatly reduced range.