/
p1.mk
91 lines (74 loc) · 3.56 KB
/
p1.mk
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
# Copyright (C) 2010 The Android Open Source Project
#
# Licensed under the Apache License, Version 2.0 (the "License");
# you may not use this file except in compliance with the License.
# You may obtain a copy of the License at
#
# http://www.apache.org/licenses/LICENSE-2.0
#
# Unless required by applicable law or agreed to in writing, software
# distributed under the License is distributed on an "AS IS" BASIS,
# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
# See the License for the specific language governing permissions and
# limitations under the License.
# This file is the device-specific product definition file for
# crespo. It lists all the overlays, files, modules and properties
# that are specific to this hardware: i.e. those are device-specific
# drivers, configuration files, settings, etc...
# Note that crespo is not a fully open device. Some of the drivers
# aren't publicly available in all circumstances, which means that some
# of the hardware capabilities aren't present in builds where those
# drivers aren't available. Such cases are handled by having this file
# separated into two halves: this half here contains the parts that
# are available to everyone, while another half in the vendor/ hierarchy
# augments that set with the parts that are only relevant when all the
# associated drivers are available. Aspects that are irrelevant but
# harmless in no-driver builds should be kept here for simplicity and
# transparency. There are two variants of the half that deals with
# the unavailable drivers: one is directly checked into the unreleased
# vendor tree and is used by engineers who have access to it. The other
# is generated by setup-makefile.sh in the same directory as this files,
# and is used by people who have access to binary versions of the drivers
# but not to the original vendor tree. Be sure to update both.
# These is the hardware-specific overlay, which points to the location
# of hardware-specific resource overrides, typically the frameworks and
# application settings that are stored in resourced.
DEVICE_PACKAGE_OVERLAYS := device/samsung/p1/overlay
# Init files
PRODUCT_COPY_FILES += \
device/samsung/p1/init.gt-p1000.rc:root/init.gt-p1000.rc \
device/samsung/p1/ueventd.gt-p1000.rc:root/ueventd.gt-p1000.rc
# vold
PRODUCT_COPY_FILES += \
device/samsung/p1/prebuilt/etc/vold.fstab:system/etc/vold.fstab
# RIL
# Permissions
PRODUCT_COPY_FILES += \
frameworks/base/data/etc/android.hardware.telephony.gsm.xml:system/etc/permissions/android.hardware.telephony.gsm.xml
# Device-specific packages
PRODUCT_PACKAGES := \
SamsungServiceMode
# Build.prop overrides
PRODUCT_PROPERTY_OVERRIDES += \
ro.telephony.call_ring.delay=3000 \
ro.telephony.call_ring.absent=true \
mobiledata.interfaces=pdp0,eth0,gprs \
ro.telephony.ril.v3=icccardstatus,datacall,signalstrength,facilitylock \
ro.ril.enable.managed.roaming=1 \
ro.ril.oem.nosim.ecclist=911,112,999,000,08,118,120,122,110,119,995 \
ro.ril.emc.mode=2
# Kernel modules
PRODUCT_COPY_FILES += $(foreach module,\
$(filter-out $(RAMDISK_MODULES),$(wildcard device/samsung/p1/modules/*.ko)),\
$(module):system/lib/modules/$(notdir $(module)))
ifeq ($(TARGET_PREBUILT_KERNEL),)
LOCAL_KERNEL := device/samsung/p1/kernel
else
LOCAL_KERNEL := $(TARGET_PREBUILT_KERNEL)
endif
PRODUCT_COPY_FILES += \
$(LOCAL_KERNEL):kernel
# Inherit P1 common device configuration.
$(call inherit-product, device/samsung/p1-common/device_base.mk)
# Propreitary drivers
$(call inherit-product-if-exists, vendor/samsung/p1/p1-vendor.mk)