0.14.0

[hathach]

• Improve compiler support for CCRX and IAR
• Add timeout to osal_queue_receive()
• Add tud_task_ext(timeout, in_isr) as generic version of tud_task(). Same as tuh_task_ext(), tuh_task()
• Enable more warnings -Wnull-dereference -Wuninitialized -Wunused -Wredundant-decls -Wconversion
• Add new examples
  • host/bare_api to demonstrate generic (app-level) enumeration and endpoint transfer
  • dual/host_hid_to_device_cdc to run both device and host stack concurrently, get HID report from host and print out to device CDC. This example only work with multiple-controller MCUs and rp2040 with the help of pio-usb as added controller.

Controller Driver (DCD & HCD)

• Enhance rhports management to better support dual roles
  • CFG_TUD_ENABLED/CFG_TUH_ENABLED, CFG_TUD_MAX_SPEED/CFG_TUH_MAX_SPEED can be used to replace CFG_TUSB_RHPORT0_MODE/CFG_TUSB_RHPORT1_MODE
  • tud_init(rphort), tuh_init(rhport) can be used to init stack on specified roothub port (controller) instead of tusb_init(void)
• Add dcd/hcd port specific defines TUP_ (stand for tinyusb port-specific)
• [dwc2]
  • Update to support stm32 h72x, h73x with only 1 otg controller
  • Fix overwrite with grstctl when disable endpoint
• [EHCI] Fix an issue with EHCI driver
• [msp430] Fix for possible bug in msp430-elf-gcc 9.3.0
• [nrf5x] Fix DMA access race condition using atomic function
• [pic32] Fix PIC32 santiy
• [rp2040]
  • Add PICO-PIO-USB as controller (device/host) support for rp2040
  • Use shared IRQ handlers, so user can also hook the USB IRQ
  • Fix resumed signal not reported to device stack
• [stm32fsdev] Add support for stm32wb55

Device Stack

• [Audio] Add support for feedback endpoint computation
  • New API tud_audio_feedback_params_cb(), tud_audio_feedback_interval_isr().
  • Supported computation method are: frequency with fixed/float or power of 2. Feedback with fifo count is not yet supported.
  • Fix nitfs (should be 3) in TUD_AUDIO_HEADSET_STEREO_DESCRIPTOR
  • Fix typo in audiod_rx_done_cb()
• [DFU] Fix coexistence with other interfaces BTH, RNDIS
• [MSC] Fix inquiry response additional length field
• [Venndor] Improve write performance

Host Stack

• Add new API tuh_configure(rhport, cfg_id, cfg_param) for dynamnic port specific behavior configuration
• [HID] Open OUT endpoint if available
• [Hub] hub clear port and device interrupts
• [USBH] Major improvement
  • Rework usbh control transfer with complete callback. New API tuh_control_xfer() though still only carry 1 usbh (no queueing) at a time.
  • Add generic endpoint transfer with tuh_edpt_open(), tuh_edpt_xfer(). Require CFG_TUH_API_EDPT_XFER=1
  • Support app-level enumeration with new APIs
    • tuh_descriptor_get(), tuh_descriptor_get_device(), tuh_descriptor_get_configuration(), tuh_descriptor_get_hid_report()
    • tuh_descriptor_get_string(), tuh_descriptor_get_manufacturer_string(), tuh_descriptor_get_product_string(), tuh_descriptor_get_serial_string()
    • Also add _sync() as sync/blocking version for above APIs

What's Changed

• Add concurrent host and device example by @tannewt in Add concurrent host and device example #1340
• Set the standard inquiry response additional length field. by @iabdalkader in Set the standard inquiry response additional length field. #1349
• Enhance rhports management by @hathach in Enhance rhports management #1350
• Solve problems with CCRX toolchain by @Wini-Buh in Solve problems with CCRX toolchain #1311
• The IAR compilier does not resolve references to fields in the anonym… by @yoyopod in The IAR compilier does not resolve references to fields in the anonym… #1353
• Updated the clearing of the status register bits to use a straight '=… by @yoyopod in Updated the clearing of the status register bits to use a straight '=… #1352
• Mcu specific by @hathach in Mcu specific #1354
• Fix CPP compilation with IAR by @alexandre-perrin in Fix CPP compilation with IAR #1345
• Open OUT endpoint for HID host by @Daft-Freak in Open OUT endpoint for HID host #1343
• fix build with esp32s2, also use dwc2 for esp example by @hathach in fix build with esp32s2, also use dwc2 for esp example #1370
• Add host string descriptor functions by @tannewt in Add host string descriptor functions #1369
• documentatio: fix bad supported dev table format by @perigoso in documentatio: fix bad supported dev table format #1371
• Fix string descriptor fetch by @tannewt in Fix string descriptor fetch #1372
• vendor: Write improvements by @kasjer in vendor: Write improvements #1289
• stm32wb55 support by @kasjer in stm32wb55 support #1374
• Modify the wrong macro definition code by @Qianhao2579 in Modify the wrong macro definition code #1379
• Add missing releases to Mynewt repository.yml by @sjanc in Add missing releases to Mynewt repository.yml #1380
• fix issue 1359 by @hathach in fix issue 1359 #1389
• in TUD_AUDIO_HEADSET_STEREO_DESCRIPTOR, _nitfs should be 3. by @ccrome in in TUD_AUDIO_HEADSET_STEREO_DESCRIPTOR, _nitfs should be 3. #1360
• Add host example that prints out info of connected devices by @tannewt in Add host example that prints out info of connected devices #1392
• More host enhancement by @hathach in More host enhancement #1393
• merge device_info into bare_api example by @hathach in merge device_info into bare_api example #1394
• Rework host control xfer by @hathach in Rework host control xfer #1397
• Add sof isr by @PanRe in Add sof isr #1402
• Host edpt xfer by @hathach in Host edpt xfer #1403
• remove cxd56 pycache folder by @hathach in remove cxd56 __pycache__ folder #1409
• Fix docs by @perigoso in Fix docs #1413
• Osal queue timeout by @hathach in Osal queue timeout #1440
• Gh action use replacement ruby by @Firefishy in Gh action use replacement ruby #1444
• set irq priority for freertos by @ccrome in set irq priority for freertos #1460
• PIO USB support by @hathach in PIO USB support #1412
• pic32 sanity fixes by @kasjer in pic32 sanity fixes #1451
• fix links in docs by @sknebel in fix links in docs #1473
• Minor cleanup of RP2040 code post addition of Pico-PIO-USB by @kilograham in Minor cleanup of RP2040 code post addition of Pico-PIO-USB #1467
• Remove lib/Pico-PIO-USB, which has moved to hw/mcu/raspberry_pi/Pico-PIO-USB. Fixes fatal: No url found for submodule path 'lib/Pico-PIO-USB' in .gitmodules #1475. by @cr1901 in Remove lib/Pico-PIO-USB, which has moved to hw/mcu/raspberry_pi/Pico-PIO-USB. Fixes #1475. #1477
• changes proposal to audio feedback computation by @hathach in changes proposal to audio feedback computation #1463
• Fix printf long int compiler error by @M3gaFr3ak in Fix printf long int compiler error #1479
• Add SOF IRQ Handler by @hathach in Add SOF IRQ Handler  #1381
• Update dwc2_stm32.h by @Nikitarc in Update dwc2_stm32.h #1438
• overwrite grstctl on edpt_disable by @Iktek in overwrite grstctl on edpt_disable #1454
• remove cmake compile macro for net example (use lwipopts.h instead) by @hathach in remove cmake compile macro for net example (use lwipopts.h instead) #1483
• Fix compile error by @tfx2001 in Fix compile error #1485
• msp430x5xx: Add fix for possible bug in msp430-elf-gcc 9.3.0. by @cr1901 in msp430x5xx: Add fix for possible bug in msp430-elf-gcc 9.3.0. #1481
• Better support multiple controllers configuration by @hathach in Better support multiple controllers configuration #1495
• add TU_ATTR_FAST_FUNC for audio sof isr call chain by @hathach in add TU_ATTR_FAST_FUNC for audio sof isr call chain #1496
• add tuh_configure() for port/dynamic host behavior config by @hathach in add tuh_configure() for port/dynamic host behavior config #1498
• make all hcd/dcd function used in isr into ram by @hathach in make all hcd/dcd function used in isr into ram  #1501
• revert sof_isr driver rename since it cause issue with existing code by @hathach in revert sof_isr driver rename since it cause issue with existing code #1505
• more dynamic controller for host by @hathach in more dynamic controller for host #1506
• Host: Add support for multi-level usb hubs by @Ryzee119 in Host: Add support for multi-level usb hubs #1480
• rp2040: make moving 1K of code into RAM optional - and off by default by @kilograham in rp2040: make moving 1K of code into RAM optional - and off by default #1512
• correct bulk size for highspeed endpoint in dynamic_configuration and usbtmc exmaples by @hathach in correct bulk size for highspeed endpoint in dynamic_configuration and usbtmc exmaples #1516
• rp2040: use shared IRQ handlers, so user can also hook the USB IRQ by @kilograham in rp2040: use shared IRQ handlers, so user can also hook the USB IRQ #1519
• Fix typo for log format by @mingpepe in Fix typo for log format #1518
• Stub out dcd_edpt_close for samd by @maddyaby in Stub out dcd_edpt_close for samd #1515
• RP2040 HCD Improvements (Hub + Keyboard + Mouse working) by @liamfraser in RP2040 HCD Improvements (Hub + Keyboard + Mouse working) #1509
• Added The Teensy 4.1 board by @ccrome in Added The Teensy 4.1 board #1526
• Hid report len uint16 by @hathach in Hid report len uint16 #1533
• Add more warnings by @hathach in Add more warnings #1534
• samd: Fix a lock-up situation at high traffic. by @robert-hh in samd: Fix a lock-up situation at high traffic. #1535
• Re-add some warning suppression for rp2040 by @kilograham in Re-add some warning suppression for rp2040 #1521
• Fix actual compiler warning on gcc 10.3.1 by @kilograham in Fix actual compiler warning on gcc 10.3.1 #1538
• Improve ci by @hathach in Improve ci #1539
• rp2040 enable SOF as resumed signal when remote wakeup by @hathach in rp2040 enable SOF as resumed signal when remote wakeup #1542
• Define CFG_BOARD_UART_BAUDRATE in CMake by @phryniszak in Define CFG_BOARD_UART_BAUDRATE in CMake #1540
• Ci parallel build by @hathach in Ci parallel build #1544
• mimxrt: Change the definitions for MIMXRT boards. by @robert-hh in mimxrt: Change the definitions for MIMXRT boards. #1543
• Fix warnings when compiling rp2040 with older version of gcc by @hathach in Fix warnings when compiling rp2040 with older version of gcc #1552
• Rework CMake example warnings some more by @kilograham in Rework CMake example warnings some more #1554
• USBTMC: Fixes and support for high-speed USB by @pigrew in USBTMC: Fixes and support for high-speed USB #1531
• temporarily revert len back to uint8_t in tud_hid_report_complete_cb() 0.14.0 release by @hathach in temporarily revert len back to uint8_t in tud_hid_report_complete_cb() 0.14.0 release #1568
• Fix typo in audiod_rx_done_cb in audio_device.c by @maddyaby in Fix typo in audiod_rx_done_cb in audio_device.c #1514
• fix issue with TUD_OPT_HIGH_SPEED by @hathach in fix issue with TUD_OPT_HIGH_SPEED #1586
• add 'stm32l052dap52' (STM32L052K8 MCU) board target by @majbthrd in add 'stm32l052dap52' (STM32L052K8 MCU) board target #1588
• dfu: Allow DFU coexistence with other interfaces (BTH, RNDIS, future one) by @kasjer in dfu: Allow DFU coexistence with other interfaces (BTH, RNDIS, future one) #1597
• nrf5x: Fix DMA access by @kasjer in nrf5x: Fix DMA access #1489
• Host hub clear port and device interrupts by @Ryzee119 in Host hub clear port and device interrupts #1603
• increase version to 0.14.0 for release by @hathach in increase version to 0.14.0 for release #1569
• update repository.yml by @hathach in update repository.yml #1609

New Contributors

• @iabdalkader made their first contribution in Set the standard inquiry response additional length field. #1349
• @yoyopod made their first contribution in The IAR compilier does not resolve references to fields in the anonym… #1353
• @alexandre-perrin made their first contribution in Fix CPP compilation with IAR #1345
• @Qianhao2579 made their first contribution in Modify the wrong macro definition code #1379
• @ccrome made their first contribution in in TUD_AUDIO_HEADSET_STEREO_DESCRIPTOR, _nitfs should be 3. #1360
• @Firefishy made their first contribution in Gh action use replacement ruby #1444
• @sknebel made their first contribution in fix links in docs #1473
• @M3gaFr3ak made their first contribution in Fix printf long int compiler error #1479
• @Nikitarc made their first contribution in Update dwc2_stm32.h #1438
• @Iktek made their first contribution in overwrite grstctl on edpt_disable #1454
• @mingpepe made their first contribution in Fix typo for log format #1518
• @maddyaby made their first contribution in Stub out dcd_edpt_close for samd #1515
• @robert-hh made their first contribution in samd: Fix a lock-up situation at high traffic. #1535
• @phryniszak made their first contribution in Define CFG_BOARD_UART_BAUDRATE in CMake #1540

Full Changelog: 0.13.0...0.14.0

---

This discussion was created from the release 0.14.0.