-
Notifications
You must be signed in to change notification settings - Fork 2
New issue
Have a question about this project? Sign up for a free GitHub account to open an issue and contact its maintainers and the community.
By clicking “Sign up for GitHub”, you agree to our terms of service and privacy statement. We’ll occasionally send you account related emails.
Already on GitHub? Sign in to your account
dspira-lessons/forum/ #2
Comments
Welcome everyone to DSPIRA! Feel free to ask questions here! |
The web page for Electronics Forum is broken. |
|
So, we're trying to cut this square can with the recommended canopener. How in the world did you do this with this can opener?!?!?!?!?! |
Did you watch the video?
Best,
Robert Baker
…On Thu, Jul 22, 2021 at 8:46 PM natewvgsi ***@***.***> wrote:
So, we're trying to cut this square can with the recommended canopener.
How in the world did you do this with this can opener?!?!?!?!?!
—
You are receiving this because you are subscribed to this thread.
Reply to this email directly, view it on GitHub
<#2 (comment)>,
or unsubscribe
<https://github.com/notifications/unsubscribe-auth/ABZERAIUHPJFZ4JAYTT7Z6LTZC3WTANCNFSM4TT25DVQ>
.
|
We did, finally figuring out we purchased the wrong Oxo can opener! We
finally did beat the can into submission and are moving on today. Thanks!!
…On Fri, Jul 23, 2021 at 9:04 AM rbaker314 ***@***.***> wrote:
Did you watch the video?
Best,
Robert Baker
On Thu, Jul 22, 2021 at 8:46 PM natewvgsi ***@***.***> wrote:
> So, we're trying to cut this square can with the recommended canopener.
> How in the world did you do this with this can opener?!?!?!?!?!
>
> —
> You are receiving this because you are subscribed to this thread.
> Reply to this email directly, view it on GitHub
> <
#2 (comment)
>,
> or unsubscribe
> <
https://github.com/notifications/unsubscribe-auth/ABZERAIUHPJFZ4JAYTT7Z6LTZC3WTANCNFSM4TT25DVQ
>
> .
>
—
You are receiving this because you commented.
Reply to this email directly, view it on GitHub
<#2 (comment)>,
or unsubscribe
<https://github.com/notifications/unsubscribe-auth/AU6E3ZQWA5TCOXLYWA4FKITTZFSFJANCNFSM4TT25DVQ>
.
--
Nate
|
Hello all - we were inspired by the work here to build a telescope for our own RET program in Hawaii. I then refined the design a bit through a graduate seminar and have added more documentation and software on the later stages to go from raw data to a rotation curve. Hopefully this is helpful to others on the forum https://github.com/interstellarmedium/HI_telescope |
Hi
You have made great progress!
Congratulations!
Cheers
Glen
… On Jan 25, 2022, at 3:29 PM, Jonathan Williams ***@***.***> wrote:
Hello all - we were inspired by the work here to build a telescope for our own RET program in Hawaii. I then refined the design a bit through a graduate seminar and have added more documentation and software on the later stages to go from raw data to a rotation curve. Hopefully this is helpful to others on the forum https://github.com/interstellarmedium/HI_telescope
—
Reply to this email directly, view it on GitHub, or unsubscribe.
Triage notifications on the go with GitHub Mobile for iOS or Android.
You are receiving this because you are subscribed to this thread.
|
Hi Jonathan,
Glad to see you’ve found the HI4PI survey.
We’ve been working with Benjamin Winkel, at Max Planck,
who provided a lower resolution, all sky image of hydrogen.
You might enjoy looking at the sky, using the jupyter notebook
at this site:
https://github.com/glangsto/hi4pi
The HI4PI images are beautiful.
Best regards
Glen
Glen I Langston, Ph. D.
Galactic Astronomy Program Director
National Science Foundation
304-456-3032
… On Jan 25, 2022, at 3:34 PM, Glen Langston ***@***.***> wrote:
This email originated from outside of the National Science Foundation. Do not click links or open attachments unless you recognize the sender and know the content is safe.
Hi
You have made great progress!
Congratulations!
Cheers
Glen
> On Jan 25, 2022, at 3:29 PM, Jonathan Williams ***@***.***> wrote:
>
>
> Hello all - we were inspired by the work here to build a telescope for our own RET program in Hawaii. I then refined the design a bit through a graduate seminar and have added more documentation and software on the later stages to go from raw data to a rotation curve. Hopefully this is helpful to others on the forum https://github.com/interstellarmedium/HI_telescope
>
> —
> Reply to this email directly, view it on GitHub, or unsubscribe.
> Triage notifications on the go with GitHub Mobile for iOS or Android.
> You are receiving this because you are subscribed to this thread.
>
—
Reply to this email directly, view it on GitHub, or unsubscribe.
Triage notifications on the go with GitHub Mobile for iOS or Android.
You are receiving this because you are subscribed to this thread.
|
Hi Glen, Thanks for pointing this out - very useful indeed! Jonathan |
Hi
I’ve been working to get all our horn observations accessible via
the very fun/remarkable jupyter notebooks.
John Makous pointed out how easy it is to use the Google Colaboratory site.
If you download the attached jupyter notebook and then upload it to the google
web site
collab.research.google.com
Then you can calibrate and view the saved observations and all the other
notebooks.
You can also upload your observations and plot them with these tools too.
Good luck!
Glen
… On Jan 25, 2022, at 3:34 PM, Glen Langston ***@***.***> wrote:
Hi
You have made great progress!
Congratulations!
Cheers
Glen
> On Jan 25, 2022, at 3:29 PM, Jonathan Williams ***@***.***> wrote:
>
>
> Hello all - we were inspired by the work here to build a telescope for our own RET program in Hawaii. I then refined the design a bit through a graduate seminar and have added more documentation and software on the later stages to go from raw data to a rotation curve. Hopefully this is helpful to others on the forum https://github.com/interstellarmedium/HI_telescope
>
> —
> Reply to this email directly, view it on GitHub, or unsubscribe.
> Triage notifications on the go with GitHub Mobile for iOS or Android.
> You are receiving this because you are subscribed to this thread.
>
|
Arg…
The GitHub site that manages these emails removes attachments.
But the attachment is available as a link also:
https://github.com/glangsto/jupyter/blob/master/MilkyWayPlottingColab.ipynb
This whole script runs in less than a minute.
For those of you not familiar with notebooks,
Click in the first box.
Then simultaneously type “Shift and Return” keys to step through the commands.
Its fun…
Cheers
Glen
… On Feb 8, 2022, at 10:46 AM, Glen Langston ***@***.***> wrote:
Hi
I’ve been working to get all our horn observations accessible via
the very fun/remarkable jupyter notebooks.
John Makous pointed out how easy it is to use the Google Colaboratory site.
If you download the attached jupyter notebook and then upload it to the google
web site
collab.research.google.com
Then you can calibrate and view the saved observations and all the other
notebooks.
You can also upload your observations and plot them with these tools too.
Good luck!
Glen
<MilkyWayPlottingColab.ipynb>
> On Jan 25, 2022, at 3:34 PM, Glen Langston ***@***.***> wrote:
>
> Hi
> You have made great progress!
>
> Congratulations!
>
> Cheers
>
> Glen
>
>
>> On Jan 25, 2022, at 3:29 PM, Jonathan Williams ***@***.***> wrote:
>>
>>
>> Hello all - we were inspired by the work here to build a telescope for our own RET program in Hawaii. I then refined the design a bit through a graduate seminar and have added more documentation and software on the later stages to go from raw data to a rotation curve. Hopefully this is helpful to others on the forum https://github.com/interstellarmedium/HI_telescope
>>
>> —
>> Reply to this email directly, view it on GitHub, or unsubscribe.
>> Triage notifications on the go with GitHub Mobile for iOS or Android.
>> You are receiving this because you are subscribed to this thread.
>>
>
|
A lot of my students have Macs, so I have been thinking about trying to set the software up on Raspberry Pi instead, but I have some logistical questions for anyone who has used the Pi. What are you using for a display? Do you have dedicated monitors, or are you remotely connecting from a laptop? And if the telescope is outside, how are you powering the Pi? Is battery life an issue? Thanks, |
Hi Evan, We have used raspberry Pis extensively. Typical we login remotely using ssh into the pi or use a vncviewer. Sometimes we attach to a monitor if available or if the initial network setup went awry. One can power the raspberry pi using power over ethernet but that may or may not require a separate hardware. @GlenLangston @glangsto has more experience with having telescopes with raspberry pi's out in the field. -P |
Hi Evan,
Hope your exploration of radio astronomy is going well.
As Pranav said, we frequently use Raspberry Pi’s for Radio Astronomy.
The code is all available as a single (large) download from:
https://drive.google.com/file/d/1tF6BaEj1Sabq6fJXeNpMsqcb8RStfqJs/view?usp=sharing
This code should be installed on a 16GB (or bigger) SD card using
balena-Etcher and then plugged into your Raspberry Pi 4B or 400.
You may need a monitor and keyboard for the initial setup, but
after that you can run using VNC, which allows you to use any laptop
to see what is going on.
The installation guide and examples are in a PDF at:
https://drive.google.com/file/d/1nvr6mUQsmsFC07G4KLD4oQAHfzUOfY-b/view?usp=sharing
Many people have successfully done this.
Good Luck!
Glen
Alternatively you can read the excellent step-by-step instructions for building
a radio telescope and install the code by downloading the packages from GitHub.
This has been extensively tested too.
See: https://wvurail.org/dspira-lessons/forum/
… On Oct 17, 2022, at 11:49 AM, Pranav Sanghavi ***@***.***> wrote:
Hi Evan,
We have used raspberry Pis extensively. Typical we login remotely using ssh into the pi or use a vncviewer. Sometimes we attach to a monitor if available or if the initial network setup went awry.
One can power the raspberry pi using power over ethernet but that may or may not require a separate hardware. @GlenLangston @glangsto has more experience with having telescopes with raspberry pi's out in the field.
-P
—
Reply to this email directly, view it on GitHub, or unsubscribe.
You are receiving this because you were mentioned.
|
Hi Glen,
Thank you for your reply. Does VNC cost money to use? When I go to download the software, I only get the option of a 14-day free trial.
Evan
________________________________
From: Glen Langston ***@***.***>
Sent: Thursday, October 20, 2022 2:26 PM
To: WVURAIL/dspira-lessons ***@***.***>
Cc: Evan Halstead ***@***.***>; Comment ***@***.***>
Subject: Re: [WVURAIL/dspira-lessons] dspira-lessons/forum/ (#2)
Hi Evan,
Hope your exploration of radio astronomy is going well.
As Pranav said, we frequently use Raspberry Pi’s for Radio Astronomy.
The code is all available as a single (large) download from:
https://drive.google.com/file/d/1tF6BaEj1Sabq6fJXeNpMsqcb8RStfqJs/view?usp=sharing
This code should be installed on a 16GB (or bigger) SD card using
balena-Etcher and then plugged into your Raspberry Pi 4B or 400.
You may need a monitor and keyboard for the initial setup, but
after that you can run using VNC, which allows you to use any laptop
to see what is going on.
The installation guide and examples are in a PDF at:
https://drive.google.com/file/d/1nvr6mUQsmsFC07G4KLD4oQAHfzUOfY-b/view?usp=sharing
Many people have successfully done this.
Good Luck!
Glen
Alternatively you can read the excellent step-by-step instructions for building
a radio telescope and install the code by downloading the packages from GitHub.
This has been extensively tested too.
See: https://wvurail.org/dspira-lessons/forum/
On Oct 17, 2022, at 11:49 AM, Pranav Sanghavi ***@***.***> wrote:
Hi Evan,
We have used raspberry Pis extensively. Typical we login remotely using ssh into the pi or use a vncviewer. Sometimes we attach to a monitor if available or if the initial network setup went awry.
One can power the raspberry pi using power over ethernet but that may or may not require a separate hardware. @GlenLangston @glangsto has more experience with having telescopes with raspberry pi's out in the field.
-P
—
Reply to this email directly, view it on GitHub, or unsubscribe.
You are receiving this because you were mentioned.
—
Reply to this email directly, view it on GitHub<#2 (comment)>, or unsubscribe<https://github.com/notifications/unsubscribe-auth/AG2PGHNBT6BTZ5EH7NI7X6DWEGFHDANCNFSM4TT25DVQ>.
You are receiving this because you commented.Message ID: ***@***.***>
|
Hi Evan,
The VNC service I’m using is free from RealVNC.
Go to downloads instead of accepting the buy it options.
There are other free options also.
Glen
… On Oct 22, 2022, at 10:36 AM, ehalstea ***@***.***> wrote:
Hi Glen,
Thank you for your reply. Does VNC cost money to use? When I go to download the software, I only get the option of a 14-day free trial.
Evan
________________________________
From: Glen Langston ***@***.***>
Sent: Thursday, October 20, 2022 2:26 PM
To: WVURAIL/dspira-lessons ***@***.***>
Cc: Evan Halstead ***@***.***>; Comment ***@***.***>
Subject: Re: [WVURAIL/dspira-lessons] dspira-lessons/forum/ (#2)
Hi Evan,
Hope your exploration of radio astronomy is going well.
As Pranav said, we frequently use Raspberry Pi’s for Radio Astronomy.
The code is all available as a single (large) download from:
https://drive.google.com/file/d/1tF6BaEj1Sabq6fJXeNpMsqcb8RStfqJs/view?usp=sharing
This code should be installed on a 16GB (or bigger) SD card using
balena-Etcher and then plugged into your Raspberry Pi 4B or 400.
You may need a monitor and keyboard for the initial setup, but
after that you can run using VNC, which allows you to use any laptop
to see what is going on.
The installation guide and examples are in a PDF at:
https://drive.google.com/file/d/1nvr6mUQsmsFC07G4KLD4oQAHfzUOfY-b/view?usp=sharing
Many people have successfully done this.
Good Luck!
Glen
Alternatively you can read the excellent step-by-step instructions for building
a radio telescope and install the code by downloading the packages from GitHub.
This has been extensively tested too.
See: https://wvurail.org/dspira-lessons/forum/
> On Oct 17, 2022, at 11:49 AM, Pranav Sanghavi ***@***.***> wrote:
>
>
> Hi Evan,
>
> We have used raspberry Pis extensively. Typical we login remotely using ssh into the pi or use a vncviewer. Sometimes we attach to a monitor if available or if the initial network setup went awry.
>
> One can power the raspberry pi using power over ethernet but that may or may not require a separate hardware. @GlenLangston @glangsto has more experience with having telescopes with raspberry pi's out in the field.
>
> -P
>
> —
> Reply to this email directly, view it on GitHub, or unsubscribe.
> You are receiving this because you were mentioned.
>
—
Reply to this email directly, view it on GitHub<#2 (comment)>, or unsubscribe<https://github.com/notifications/unsubscribe-auth/AG2PGHNBT6BTZ5EH7NI7X6DWEGFHDANCNFSM4TT25DVQ>.
You are receiving this because you commented.Message ID: ***@***.***>
—
Reply to this email directly, view it on GitHub, or unsubscribe.
You are receiving this because you were mentioned.
|
Thanks, Glen.
When you are out in the field, how do you power the Raspberry Pi? Also, do you have any experience with those small touch screen displays?
Evan
________________________________
From: Glen Langston ***@***.***>
Sent: Saturday, October 22, 2022 10:43 AM
To: WVURAIL/dspira-lessons ***@***.***>
Cc: Evan Halstead ***@***.***>; Comment ***@***.***>
Subject: Re: [WVURAIL/dspira-lessons] dspira-lessons/forum/ (#2)
Hi Evan,
The VNC service I’m using is free from RealVNC.
Go to downloads instead of accepting the buy it options.
There are other free options also.
Glen
On Oct 22, 2022, at 10:36 AM, ehalstea ***@***.***> wrote:
Hi Glen,
Thank you for your reply. Does VNC cost money to use? When I go to download the software, I only get the option of a 14-day free trial.
Evan
________________________________
From: Glen Langston ***@***.***>
Sent: Thursday, October 20, 2022 2:26 PM
To: WVURAIL/dspira-lessons ***@***.***>
Cc: Evan Halstead ***@***.***>; Comment ***@***.***>
Subject: Re: [WVURAIL/dspira-lessons] dspira-lessons/forum/ (#2)
Hi Evan,
Hope your exploration of radio astronomy is going well.
As Pranav said, we frequently use Raspberry Pi’s for Radio Astronomy.
The code is all available as a single (large) download from:
https://drive.google.com/file/d/1tF6BaEj1Sabq6fJXeNpMsqcb8RStfqJs/view?usp=sharing
This code should be installed on a 16GB (or bigger) SD card using
balena-Etcher and then plugged into your Raspberry Pi 4B or 400.
You may need a monitor and keyboard for the initial setup, but
after that you can run using VNC, which allows you to use any laptop
to see what is going on.
The installation guide and examples are in a PDF at:
https://drive.google.com/file/d/1nvr6mUQsmsFC07G4KLD4oQAHfzUOfY-b/view?usp=sharing
Many people have successfully done this.
Good Luck!
Glen
Alternatively you can read the excellent step-by-step instructions for building
a radio telescope and install the code by downloading the packages from GitHub.
This has been extensively tested too.
See: https://wvurail.org/dspira-lessons/forum/
> On Oct 17, 2022, at 11:49 AM, Pranav Sanghavi ***@***.***> wrote:
>
>
> Hi Evan,
>
> We have used raspberry Pis extensively. Typical we login remotely using ssh into the pi or use a vncviewer. Sometimes we attach to a monitor if available or if the initial network setup went awry.
>
> One can power the raspberry pi using power over ethernet but that may or may not require a separate hardware. @GlenLangston @glangsto has more experience with having telescopes with raspberry pi's out in the field.
>
> -P
>
> —
> Reply to this email directly, view it on GitHub, or unsubscribe.
> You are receiving this because you were mentioned.
>
—
Reply to this email directly, view it on GitHub<#2 (comment)>, or unsubscribe<https://github.com/notifications/unsubscribe-auth/AG2PGHNBT6BTZ5EH7NI7X6DWEGFHDANCNFSM4TT25DVQ>.
You are receiving this because you commented.Message ID: ***@***.***>
—
Reply to this email directly, view it on GitHub, or unsubscribe.
You are receiving this because you were mentioned.
—
Reply to this email directly, view it on GitHub<#2 (comment)>, or unsubscribe<https://github.com/notifications/unsubscribe-auth/AG2PGHPCUVEQZ4PT3KIM6HLWEP4QBANCNFSM4TT25DVQ>.
You are receiving this because you commented.Message ID: ***@***.***>
|
Hi Evan,
I have a mini-network of 4 telescopes watching for fast transient events
(< 1 micro second in duration). These telescopes are powered by
Power Over Ethernet (POE) routers and splitters. (The key science goal
is cosmic ray, and maybe neutrino, detections).
For Raspberry Pi 400, a slightly more powerful POE splitter is needed. The 400 needs
20 Watts, which is not much, but 4 of them require 80 Watts.
1)UCTRONICS USB-C PoE Splitter Gigabit, PoE to USB-C 5V/4A Power Supply for Raspberry Pi 4 and More,
802.3at Power Over Ethernet to USB Type-C Adapter UCTRONICS
https://www.amazon.com/gp/product/B07V35DH5F/ref=ppx_yo_dt_b_search_asin_image?ie=UTF8&psc=1
2) SODOLA 8 Port Gigabit PoE Switch with 2 Gigabit Ethernet Uplink ,8 PoE+ Ports 1000Mbp,120W 48V Built-in Power,802.3af/at Compliant,Fanless Metal,Plug & Play Unmanaged PoE Network Switch
https://www.amazon.com/gp/product/B09N98CPK3/ref=ppx_yo_dt_b_asin_title_o00_s00?ie=UTF8&psc=1
This allows simply running a single long ethernet cable to each telescope, and no extra
power wires.
Good Luck!
Glen
… On Oct 25, 2022, at 12:07 PM, ehalstea ***@***.***> wrote:
Thanks, Glen.
When you are out in the field, how do you power the Raspberry Pi? Also, do you have any experience with those small touch screen displays?
Evan
________________________________
From: Glen Langston ***@***.***>
Sent: Saturday, October 22, 2022 10:43 AM
To: WVURAIL/dspira-lessons ***@***.***>
Cc: Evan Halstead ***@***.***>; Comment ***@***.***>
Subject: Re: [WVURAIL/dspira-lessons] dspira-lessons/forum/ (#2)
Hi Evan,
The VNC service I’m using is free from RealVNC.
Go to downloads instead of accepting the buy it options.
There are other free options also.
Glen
> On Oct 22, 2022, at 10:36 AM, ehalstea ***@***.***> wrote:
>
>
> Hi Glen,
>
> Thank you for your reply. Does VNC cost money to use? When I go to download the software, I only get the option of a 14-day free trial.
>
> Evan
> ________________________________
> From: Glen Langston ***@***.***>
> Sent: Thursday, October 20, 2022 2:26 PM
> To: WVURAIL/dspira-lessons ***@***.***>
> Cc: Evan Halstead ***@***.***>; Comment ***@***.***>
> Subject: Re: [WVURAIL/dspira-lessons] dspira-lessons/forum/ (#2)
>
>
> Hi Evan,
>
> Hope your exploration of radio astronomy is going well.
>
> As Pranav said, we frequently use Raspberry Pi’s for Radio Astronomy.
>
> The code is all available as a single (large) download from:
> https://drive.google.com/file/d/1tF6BaEj1Sabq6fJXeNpMsqcb8RStfqJs/view?usp=sharing
>
> This code should be installed on a 16GB (or bigger) SD card using
> balena-Etcher and then plugged into your Raspberry Pi 4B or 400.
>
> You may need a monitor and keyboard for the initial setup, but
> after that you can run using VNC, which allows you to use any laptop
> to see what is going on.
>
> The installation guide and examples are in a PDF at:
> https://drive.google.com/file/d/1nvr6mUQsmsFC07G4KLD4oQAHfzUOfY-b/view?usp=sharing
>
> Many people have successfully done this.
>
> Good Luck!
>
> Glen
>
> Alternatively you can read the excellent step-by-step instructions for building
> a radio telescope and install the code by downloading the packages from GitHub.
>
> This has been extensively tested too.
>
> See: https://wvurail.org/dspira-lessons/forum/
>
>
>
>
> > On Oct 17, 2022, at 11:49 AM, Pranav Sanghavi ***@***.***> wrote:
> >
> >
> > Hi Evan,
> >
> > We have used raspberry Pis extensively. Typical we login remotely using ssh into the pi or use a vncviewer. Sometimes we attach to a monitor if available or if the initial network setup went awry.
> >
> > One can power the raspberry pi using power over ethernet but that may or may not require a separate hardware. @GlenLangston @glangsto has more experience with having telescopes with raspberry pi's out in the field.
> >
> > -P
> >
> > —
> > Reply to this email directly, view it on GitHub, or unsubscribe.
> > You are receiving this because you were mentioned.
> >
>
>
> —
> Reply to this email directly, view it on GitHub<#2 (comment)>, or unsubscribe<https://github.com/notifications/unsubscribe-auth/AG2PGHNBT6BTZ5EH7NI7X6DWEGFHDANCNFSM4TT25DVQ>.
> You are receiving this because you commented.Message ID: ***@***.***>
> —
> Reply to this email directly, view it on GitHub, or unsubscribe.
> You are receiving this because you were mentioned.
>
—
Reply to this email directly, view it on GitHub<#2 (comment)>, or unsubscribe<https://github.com/notifications/unsubscribe-auth/AG2PGHPCUVEQZ4PT3KIM6HLWEP4QBANCNFSM4TT25DVQ>.
You are receiving this because you commented.Message ID: ***@***.***>
—
Reply to this email directly, view it on GitHub, or unsubscribe.
You are receiving this because you were mentioned.
|
Thanks, Glen. Do you happen to know if the custom OS for the raspberry pi with GnuRadio supports touch displays?
Evan
________________________________
From: Glen Langston ***@***.***>
Sent: Tuesday, October 25, 2022 2:57 PM
To: WVURAIL/dspira-lessons ***@***.***>
Cc: Evan Halstead ***@***.***>; Comment ***@***.***>
Subject: Re: [WVURAIL/dspira-lessons] dspira-lessons/forum/ (#2)
Hi Evan,
I have a mini-network of 4 telescopes watching for fast transient events
(< 1 micro second in duration). These telescopes are powered by
Power Over Ethernet (POE) routers and splitters. (The key science goal
is cosmic ray, and maybe neutrino, detections).
For Raspberry Pi 400, a slightly more powerful POE splitter is needed. The 400 needs
20 Watts, which is not much, but 4 of them require 80 Watts.
1)UCTRONICS USB-C PoE Splitter Gigabit, PoE to USB-C 5V/4A Power Supply for Raspberry Pi 4 and More,
802.3at Power Over Ethernet to USB Type-C Adapter UCTRONICS
https://www.amazon.com/gp/product/B07V35DH5F/ref=ppx_yo_dt_b_search_asin_image?ie=UTF8&psc=1
2) SODOLA 8 Port Gigabit PoE Switch with 2 Gigabit Ethernet Uplink ,8 PoE+ Ports 1000Mbp,120W 48V Built-in Power,802.3af/at Compliant,Fanless Metal,Plug & Play Unmanaged PoE Network Switch
https://www.amazon.com/gp/product/B09N98CPK3/ref=ppx_yo_dt_b_asin_title_o00_s00?ie=UTF8&psc=1
This allows simply running a single long ethernet cable to each telescope, and no extra
power wires.
Good Luck!
Glen
On Oct 25, 2022, at 12:07 PM, ehalstea ***@***.***> wrote:
Thanks, Glen.
When you are out in the field, how do you power the Raspberry Pi? Also, do you have any experience with those small touch screen displays?
Evan
________________________________
From: Glen Langston ***@***.***>
Sent: Saturday, October 22, 2022 10:43 AM
To: WVURAIL/dspira-lessons ***@***.***>
Cc: Evan Halstead ***@***.***>; Comment ***@***.***>
Subject: Re: [WVURAIL/dspira-lessons] dspira-lessons/forum/ (#2)
Hi Evan,
The VNC service I’m using is free from RealVNC.
Go to downloads instead of accepting the buy it options.
There are other free options also.
Glen
> On Oct 22, 2022, at 10:36 AM, ehalstea ***@***.***> wrote:
>
>
> Hi Glen,
>
> Thank you for your reply. Does VNC cost money to use? When I go to download the software, I only get the option of a 14-day free trial.
>
> Evan
> ________________________________
> From: Glen Langston ***@***.***>
> Sent: Thursday, October 20, 2022 2:26 PM
> To: WVURAIL/dspira-lessons ***@***.***>
> Cc: Evan Halstead ***@***.***>; Comment ***@***.***>
> Subject: Re: [WVURAIL/dspira-lessons] dspira-lessons/forum/ (#2)
>
>
> Hi Evan,
>
> Hope your exploration of radio astronomy is going well.
>
> As Pranav said, we frequently use Raspberry Pi’s for Radio Astronomy.
>
> The code is all available as a single (large) download from:
> https://drive.google.com/file/d/1tF6BaEj1Sabq6fJXeNpMsqcb8RStfqJs/view?usp=sharing
>
> This code should be installed on a 16GB (or bigger) SD card using
> balena-Etcher and then plugged into your Raspberry Pi 4B or 400.
>
> You may need a monitor and keyboard for the initial setup, but
> after that you can run using VNC, which allows you to use any laptop
> to see what is going on.
>
> The installation guide and examples are in a PDF at:
> https://drive.google.com/file/d/1nvr6mUQsmsFC07G4KLD4oQAHfzUOfY-b/view?usp=sharing
>
> Many people have successfully done this.
>
> Good Luck!
>
> Glen
>
> Alternatively you can read the excellent step-by-step instructions for building
> a radio telescope and install the code by downloading the packages from GitHub.
>
> This has been extensively tested too.
>
> See: https://wvurail.org/dspira-lessons/forum/
>
>
>
>
> > On Oct 17, 2022, at 11:49 AM, Pranav Sanghavi ***@***.***> wrote:
> >
> >
> > Hi Evan,
> >
> > We have used raspberry Pis extensively. Typical we login remotely using ssh into the pi or use a vncviewer. Sometimes we attach to a monitor if available or if the initial network setup went awry.
> >
> > One can power the raspberry pi using power over ethernet but that may or may not require a separate hardware. @GlenLangston @glangsto has more experience with having telescopes with raspberry pi's out in the field.
> >
> > -P
> >
> > —
> > Reply to this email directly, view it on GitHub, or unsubscribe.
> > You are receiving this because you were mentioned.
> >
>
>
> —
> Reply to this email directly, view it on GitHub<#2 (comment)>, or unsubscribe<https://github.com/notifications/unsubscribe-auth/AG2PGHNBT6BTZ5EH7NI7X6DWEGFHDANCNFSM4TT25DVQ>.
> You are receiving this because you commented.Message ID: ***@***.***>
> —
> Reply to this email directly, view it on GitHub, or unsubscribe.
> You are receiving this because you were mentioned.
>
—
Reply to this email directly, view it on GitHub<#2 (comment)>, or unsubscribe<https://github.com/notifications/unsubscribe-auth/AG2PGHPCUVEQZ4PT3KIM6HLWEP4QBANCNFSM4TT25DVQ>.
You are receiving this because you commented.Message ID: ***@***.***>
—
Reply to this email directly, view it on GitHub, or unsubscribe.
You are receiving this because you were mentioned.
—
Reply to this email directly, view it on GitHub<#2 (comment)>, or unsubscribe<https://github.com/notifications/unsubscribe-auth/AG2PGHNFOGUPZPOM5QGGGMLWFAUTJANCNFSM4TT25DVQ>.
You are receiving this because you commented.Message ID: ***@***.***>
|
Hi Evan,
I forgot you asked about the mini raspberry pi touch displays.
Yes they do work, including the touch display, but I found them
too small to be useful for much. Maybe my eyesight is not
what it could be, but I much prefer VNCing into the device
remotely.
If you send me a separate email, I will send you the info to VNC
into a running telescope, if you’d like.
Cheers
glen -dot- i -dot- langston -at- gmail -dot- com
You can see the interface via VNC with IP
162.249.150.125
But you need the login info
… On Oct 26, 2022, at 11:09 AM, ehalstea ***@***.***> wrote:
Thanks, Glen. Do you happen to know if the custom OS for the raspberry pi with GnuRadio supports touch displays?
Evan
________________________________
From: Glen Langston ***@***.***>
Sent: Tuesday, October 25, 2022 2:57 PM
To: WVURAIL/dspira-lessons ***@***.***>
Cc: Evan Halstead ***@***.***>; Comment ***@***.***>
Subject: Re: [WVURAIL/dspira-lessons] dspira-lessons/forum/ (#2)
Hi Evan,
I have a mini-network of 4 telescopes watching for fast transient events
(< 1 micro second in duration). These telescopes are powered by
Power Over Ethernet (POE) routers and splitters. (The key science goal
is cosmic ray, and maybe neutrino, detections).
For Raspberry Pi 400, a slightly more powerful POE splitter is needed. The 400 needs
20 Watts, which is not much, but 4 of them require 80 Watts.
1)UCTRONICS USB-C PoE Splitter Gigabit, PoE to USB-C 5V/4A Power Supply for Raspberry Pi 4 and More,
802.3at Power Over Ethernet to USB Type-C Adapter UCTRONICS
https://www.amazon.com/gp/product/B07V35DH5F/ref=ppx_yo_dt_b_search_asin_image?ie=UTF8&psc=1
2) SODOLA 8 Port Gigabit PoE Switch with 2 Gigabit Ethernet Uplink ,8 PoE+ Ports 1000Mbp,120W 48V Built-in Power,802.3af/at Compliant,Fanless Metal,Plug & Play Unmanaged PoE Network Switch
https://www.amazon.com/gp/product/B09N98CPK3/ref=ppx_yo_dt_b_asin_title_o00_s00?ie=UTF8&psc=1
This allows simply running a single long ethernet cable to each telescope, and no extra
power wires.
Good Luck!
Glen
> On Oct 25, 2022, at 12:07 PM, ehalstea ***@***.***> wrote:
>
>
> Thanks, Glen.
>
> When you are out in the field, how do you power the Raspberry Pi? Also, do you have any experience with those small touch screen displays?
>
> Evan
> ________________________________
> From: Glen Langston ***@***.***>
> Sent: Saturday, October 22, 2022 10:43 AM
> To: WVURAIL/dspira-lessons ***@***.***>
> Cc: Evan Halstead ***@***.***>; Comment ***@***.***>
> Subject: Re: [WVURAIL/dspira-lessons] dspira-lessons/forum/ (#2)
>
>
> Hi Evan,
>
> The VNC service I’m using is free from RealVNC.
>
> Go to downloads instead of accepting the buy it options.
>
> There are other free options also.
>
> Glen
>
>
>
> > On Oct 22, 2022, at 10:36 AM, ehalstea ***@***.***> wrote:
> >
> >
> > Hi Glen,
> >
> > Thank you for your reply. Does VNC cost money to use? When I go to download the software, I only get the option of a 14-day free trial.
> >
> > Evan
> > ________________________________
> > From: Glen Langston ***@***.***>
> > Sent: Thursday, October 20, 2022 2:26 PM
> > To: WVURAIL/dspira-lessons ***@***.***>
> > Cc: Evan Halstead ***@***.***>; Comment ***@***.***>
> > Subject: Re: [WVURAIL/dspira-lessons] dspira-lessons/forum/ (#2)
> >
> >
> > Hi Evan,
> >
> > Hope your exploration of radio astronomy is going well.
> >
> > As Pranav said, we frequently use Raspberry Pi’s for Radio Astronomy.
> >
> > The code is all available as a single (large) download from:
> > https://drive.google.com/file/d/1tF6BaEj1Sabq6fJXeNpMsqcb8RStfqJs/view?usp=sharing
> >
> > This code should be installed on a 16GB (or bigger) SD card using
> > balena-Etcher and then plugged into your Raspberry Pi 4B or 400.
> >
> > You may need a monitor and keyboard for the initial setup, but
> > after that you can run using VNC, which allows you to use any laptop
> > to see what is going on.
> >
> > The installation guide and examples are in a PDF at:
> > https://drive.google.com/file/d/1nvr6mUQsmsFC07G4KLD4oQAHfzUOfY-b/view?usp=sharing
> >
> > Many people have successfully done this.
> >
> > Good Luck!
> >
> > Glen
> >
> > Alternatively you can read the excellent step-by-step instructions for building
> > a radio telescope and install the code by downloading the packages from GitHub.
> >
> > This has been extensively tested too.
> >
> > See: https://wvurail.org/dspira-lessons/forum/
> >
> >
> >
> >
> > > On Oct 17, 2022, at 11:49 AM, Pranav Sanghavi ***@***.***> wrote:
> > >
> > >
> > > Hi Evan,
> > >
> > > We have used raspberry Pis extensively. Typical we login remotely using ssh into the pi or use a vncviewer. Sometimes we attach to a monitor if available or if the initial network setup went awry.
> > >
> > > One can power the raspberry pi using power over ethernet but that may or may not require a separate hardware. @GlenLangston @glangsto has more experience with having telescopes with raspberry pi's out in the field.
> > >
> > > -P
> > >
> > > —
> > > Reply to this email directly, view it on GitHub, or unsubscribe.
> > > You are receiving this because you were mentioned.
> > >
> >
> >
> > —
> > Reply to this email directly, view it on GitHub<#2 (comment)>, or unsubscribe<https://github.com/notifications/unsubscribe-auth/AG2PGHNBT6BTZ5EH7NI7X6DWEGFHDANCNFSM4TT25DVQ>.
> > You are receiving this because you commented.Message ID: ***@***.***>
> > —
> > Reply to this email directly, view it on GitHub, or unsubscribe.
> > You are receiving this because you were mentioned.
> >
>
>
> —
> Reply to this email directly, view it on GitHub<#2 (comment)>, or unsubscribe<https://github.com/notifications/unsubscribe-auth/AG2PGHPCUVEQZ4PT3KIM6HLWEP4QBANCNFSM4TT25DVQ>.
> You are receiving this because you commented.Message ID: ***@***.***>
> —
> Reply to this email directly, view it on GitHub, or unsubscribe.
> You are receiving this because you were mentioned.
>
—
Reply to this email directly, view it on GitHub<#2 (comment)>, or unsubscribe<https://github.com/notifications/unsubscribe-auth/AG2PGHNFOGUPZPOM5QGGGMLWFAUTJANCNFSM4TT25DVQ>.
You are receiving this because you commented.Message ID: ***@***.***>
—
Reply to this email directly, view it on GitHub, or unsubscribe.
You are receiving this because you were mentioned.
|
Hi - I'd like to try out the DSPIRA activities. I ran into a problem early in the process, where I'm getting an error on cmake. The error messages are: and then there was Unknown CMake command "GR_SWIG_MAKE" Is this is a common problem, and is there a known solution? |
Hi George,
Glad to hear you’re interested in Radio Astronomy and are ready to start
observations.
It appears that one critical step is necessary if you’ve installed
GNUradio 3.10 or later. It took me a few tries to get the sequence correct,
as it has been a while since I reinstalled from scratch.
The first number it the command history number, ignore that:
1079 mkdir temp
1080 cd temp
1081 git clone https://www.github.com/WVURAIL/gr-radio_astro
1082 cd gr-radio_astro/
...
1095 git branch -r -l
...
1101 git checkout gr310
1102 mkdir build
...
1104 cd build
1105 cmake ../
1106 make -j 3
This just worked fine. Probably the key piece that is missing is the:
git checkout gr310
step, which removes all mention of code needing SWIG. There are a few more steps
after this including:
sudo make install
and
sudo ldconfig
Let us know how this works out for you!
Best regards
Glen
PS Change the mkdir step to place the code wherever you want it.
I typically use: ~/Research
ie:
mkdir ~/Research
cd ~/Research
But this is not required.
… On Jan 6, 2023, at 10:19 AM, ghassel ***@***.***> wrote:
Hi - I'd like to try out the DSPIRA activities. I ran into a problem early in the process, where I'm getting an error on cmake. The error messages are:
CMake Error at swig/CMakeLists.txt.37 (include):
include could not find the requested file:
GrSwig
and then there was Unknown CMake command "GR_SWIG_MAKE"
Is this is a common problem, and is there a known solution?
Thanks!
-George
—
Reply to this email directly, view it on GitHub, or unsubscribe.
You are receiving this because you were mentioned.Message ID: ***@***.***>
|
Hi Glen,
Thanks for the help and instructions. I got a little bit farther, but now
have a new error on cmake that doesn't seem as informative as the previous
one. I'm copying the last parts of what came up, and I can send along any
more info. that might be useful:
…-- Found Boost:
/usr/lib/x86_64-linux-gnu/cmake/Boost-1.74.0/BoostConfig.cmake (found
suitable version "1.74.0", minimum required is "1.74.0") found components:
date_time program_options system regex thread unit_test_framework
-- Found Volk: Volk::volk
CMake Error at /usr/local/lib/cmake/gnuradio/GnuradioConfig.cmake:40
(include):
include could not find requested file:
/usr/local/lib/cmake/gnuradio/gnuradio-pmtConfig.cmake
Call Stack (most recent call first):
CMakeLists.txt:88 (find_package)
CMake Error at /usr/local/lib/cmake/gnuradio/GnuradioConfig.cmake:41
(include):
include could not find requested file:
/usr/local/lib/cmake/gnuradio/gnuradio-runtimeConfig.cmake
Call Stack (most recent call first):
CMakeLists.txt:88 (find_package)
-- Found Git: /usr/bin/git
-- Extracting version information from git describe...
fatal: No annotated tags can describe
'1cdb8703a1905547f3d7a9e404e068c7c8d29fa0'.
However, there were unannotated tags: try --tags.
-- Found Doxygen: /usr/bin/doxygen (found version "1.9.1") found
components: doxygen missing components: dot
-- Using install prefix: /usr/local
-- Building for version: g1cdb870 / 1.0.0git
-- No C++ unit tests... skipping
-- PYTHON_EXECUTABLE not set - using default python3
-- Found PythonInterp: /usr/bin/python3.10 (found version "3.10.7")
-- Found PythonLibs: /usr/lib/x86_64-linux-gnu/libpython3.10.so (found
suitable exact version "3.10.7")
-- PYTHON and GRC components are disabled
-- Configuring incomplete, errors occurred!
See also
"/home/viper/Research/temp/gr-radio_astro/build/CMakeFiles/CMakeOutput.log"
I appreciate any suggestions or insights. Thanks!!
On Sat, Jan 7, 2023 at 10:48 AM Glen Langston ***@***.***>
wrote:
Hi George,
Glad to hear you’re interested in Radio Astronomy and are ready to start
observations.
It appears that one critical step is necessary if you’ve installed
GNUradio 3.10 or later. It took me a few tries to get the sequence correct,
as it has been a while since I reinstalled from scratch.
The first number it the command history number, ignore that:
1079 mkdir temp
1080 cd temp
1081 git clone https://www.github.com/WVURAIL/gr-radio_astro
1082 cd gr-radio_astro/
...
1095 git branch -r -l
...
1101 git checkout gr310
1102 mkdir build
...
1104 cd build
1105 cmake ../
1106 make -j 3
This just worked fine. Probably the key piece that is missing is the:
git checkout gr310
step, which removes all mention of code needing SWIG. There are a few more
steps
after this including:
sudo make install
and
sudo ldconfig
Let us know how this works out for you!
Best regards
Glen
PS Change the mkdir step to place the code wherever you want it.
I typically use: ~/Research
ie:
mkdir ~/Research
cd ~/Research
But this is not required.
> On Jan 6, 2023, at 10:19 AM, ghassel ***@***.***> wrote:
>
>
> Hi - I'd like to try out the DSPIRA activities. I ran into a problem
early in the process, where I'm getting an error on cmake. The error
messages are:
> CMake Error at swig/CMakeLists.txt.37 (include):
> include could not find the requested file:
> GrSwig
> and then there was Unknown CMake command "GR_SWIG_MAKE"
> Is this is a common problem, and is there a known solution?
> Thanks!
> -George
> —
> Reply to this email directly, view it on GitHub, or unsubscribe.
> You are receiving this because you were mentioned.Message ID:
***@***.***>
—
Reply to this email directly, view it on GitHub
<#2 (comment)>,
or unsubscribe
<https://github.com/notifications/unsubscribe-auth/AG5YWTF25PYUY6X3S727JW3WRGF4VANCNFSM4TT25DVQ>
.
You are receiving this because you commented.Message ID:
***@***.***>
|
Hi George,
That was quick work getting to the next issue!
At least the git checkout step worked.
Now I’m guessing that some “sudo aptget install commands”
will fix these problems, starting with first messages first.
Since the process dies at doxygen, try this command and let us know what happens:
sudo apt-get install doxygen
This should yield a question about updating, which you should answer YES to.
Also consider:
sudo apt-get update
can be very helpful, but has the danger of breaking things.
Glen
PS: What computer type are you using? If a Raspberry pi, then you could
just download the entire operating system image.
Below are what successful CMAKE messages look like. It might be you need to
update doxygen or “dot”
***@***.***:~/temp/gr-radio_astro/build $ cmake ../
-- The CXX compiler identification is GNU 10.2.1
-- The C compiler identification is GNU 10.2.1
-- Detecting CXX compiler ABI info
-- Detecting CXX compiler ABI info - done
-- Check for working CXX compiler: /usr/bin/c++ - skipped
-- Detecting CXX compile features
-- Detecting CXX compile features - done
-- Detecting C compiler ABI info
-- Detecting C compiler ABI info - done
-- Check for working C compiler: /usr/bin/cc - skipped
-- Detecting C compile features
-- Detecting C compile features - done
-- Build type not specified: defaulting to release.
-- Looking for pthread.h
-- Looking for pthread.h - found
-- Performing Test CMAKE_HAVE_LIBC_PTHREAD
-- Performing Test CMAKE_HAVE_LIBC_PTHREAD - Failed
-- Looking for pthread_create in pthreads
-- Looking for pthread_create in pthreads - not found
-- Looking for pthread_create in pthread
-- Looking for pthread_create in pthread - found
-- Found Threads: TRUE
-- Found PkgConfig: /usr/bin/pkg-config (found version "0.29.2")
-- Checking for module 'gmp'
-- Found gmp, version 6.2.1
-- Found GMP: /usr/lib/aarch64-linux-gnu/libgmpxx.so
-- Using GMP.
-- Found MPLIB: /usr/lib/aarch64-linux-gnu/libgmpxx.so
-- Found Boost: /usr/lib/aarch64-linux-gnu/cmake/Boost-1.74.0/BoostConfig.cmake (found suitable version "1.74.0", minimum required is "1.74.0") found components: date_time program_options system regex thread unit_test_framework
-- Found Volk: Volk::volk
-- User set python executable /usr/bin/python3
-- Found PythonInterp: /usr/bin/python3 (found version "3.9.2")
-- Found PythonLibs: /usr/lib/aarch64-linux-gnu/libpython3.9.so (found suitable exact version "3.9.2")
-- Found Git: /usr/bin/git
-- Extracting version information from git describe...
-- Found Doxygen: /usr/bin/doxygen (found version "1.9.1") found components: doxygen dot
-- Using install prefix: /usr/local
-- Building for version: 1cdb8703 / 1.0.0git
-- No C++ unit tests... skipping
-- PYTHON and GRC components are enabled
-- Python checking for pygccxml - not found
-- Found PythonLibs: /usr/lib/aarch64-linux-gnu/libpython3.9.so
-- Performing Test HAS_FLTO
-- Performing Test HAS_FLTO - Success
-- Found pybind11: /usr/include (found version "2.6.2" )
-- Configuring done
-- Generating done
-- Build files have been written to: /home/radioastro/temp/gr-radio_astro/build
… On Jan 7, 2023, at 11:32 AM, ghassel ***@***.***> wrote:
Hi Glen,
Thanks for the help and instructions. I got a little bit farther, but now
have a new error on cmake that doesn't seem as informative as the previous
one. I'm copying the last parts of what came up, and I can send along any
more info. that might be useful:
-- Found Boost:
/usr/lib/x86_64-linux-gnu/cmake/Boost-1.74.0/BoostConfig.cmake (found
suitable version "1.74.0", minimum required is "1.74.0") found components:
date_time program_options system regex thread unit_test_framework
-- Found Volk: Volk::volk
CMake Error at /usr/local/lib/cmake/gnuradio/GnuradioConfig.cmake:40
(include):
include could not find requested file:
/usr/local/lib/cmake/gnuradio/gnuradio-pmtConfig.cmake
Call Stack (most recent call first):
CMakeLists.txt:88 (find_package)
CMake Error at /usr/local/lib/cmake/gnuradio/GnuradioConfig.cmake:41
(include):
include could not find requested file:
/usr/local/lib/cmake/gnuradio/gnuradio-runtimeConfig.cmake
Call Stack (most recent call first):
CMakeLists.txt:88 (find_package)
-- Found Git: /usr/bin/git
-- Extracting version information from git describe...
fatal: No annotated tags can describe
'1cdb8703a1905547f3d7a9e404e068c7c8d29fa0'.
However, there were unannotated tags: try --tags.
-- Found Doxygen: /usr/bin/doxygen (found version "1.9.1") found
components: doxygen missing components: dot
-- Using install prefix: /usr/local
-- Building for version: g1cdb870 / 1.0.0git
-- No C++ unit tests... skipping
-- PYTHON_EXECUTABLE not set - using default python3
-- Found PythonInterp: /usr/bin/python3.10 (found version "3.10.7")
-- Found PythonLibs: /usr/lib/x86_64-linux-gnu/libpython3.10.so (found
suitable exact version "3.10.7")
-- PYTHON and GRC components are disabled
-- Configuring incomplete, errors occurred!
See also
"/home/viper/Research/temp/gr-radio_astro/build/CMakeFiles/CMakeOutput.log"
I appreciate any suggestions or insights. Thanks!!
On Sat, Jan 7, 2023 at 10:48 AM Glen Langston ***@***.***>
wrote:
> Hi George,
>
> Glad to hear you’re interested in Radio Astronomy and are ready to start
> observations.
>
> It appears that one critical step is necessary if you’ve installed
> GNUradio 3.10 or later. It took me a few tries to get the sequence correct,
> as it has been a while since I reinstalled from scratch.
>
> The first number it the command history number, ignore that:
> 1079 mkdir temp
> 1080 cd temp
> 1081 git clone https://www.github.com/WVURAIL/gr-radio_astro
> 1082 cd gr-radio_astro/
> ...
> 1095 git branch -r -l
> ...
> 1101 git checkout gr310
> 1102 mkdir build
> ...
> 1104 cd build
> 1105 cmake ../
> 1106 make -j 3
>
> This just worked fine. Probably the key piece that is missing is the:
>
> git checkout gr310
>
> step, which removes all mention of code needing SWIG. There are a few more
> steps
> after this including:
> sudo make install
> and
> sudo ldconfig
>
> Let us know how this works out for you!
>
> Best regards
>
> Glen
>
> PS Change the mkdir step to place the code wherever you want it.
> I typically use: ~/Research
>
> ie:
>
> mkdir ~/Research
> cd ~/Research
>
> But this is not required.
>
>
> > On Jan 6, 2023, at 10:19 AM, ghassel ***@***.***> wrote:
> >
> >
> > Hi - I'd like to try out the DSPIRA activities. I ran into a problem
> early in the process, where I'm getting an error on cmake. The error
> messages are:
> > CMake Error at swig/CMakeLists.txt.37 (include):
> > include could not find the requested file:
> > GrSwig
> > and then there was Unknown CMake command "GR_SWIG_MAKE"
> > Is this is a common problem, and is there a known solution?
> > Thanks!
> > -George
> > —
> > Reply to this email directly, view it on GitHub, or unsubscribe.
> > You are receiving this because you were mentioned.Message ID:
> ***@***.***>
>
> —
> Reply to this email directly, view it on GitHub
> <#2 (comment)>,
> or unsubscribe
> <https://github.com/notifications/unsubscribe-auth/AG5YWTF25PYUY6X3S727JW3WRGF4VANCNFSM4TT25DVQ>
> .
> You are receiving this because you commented.Message ID:
> ***@***.***>
>
—
Reply to this email directly, view it on GitHub, or unsubscribe.
You are receiving this because you were mentioned.Message ID: ***@***.***>
|
Hello again George,
I read your messages a bit further and found the job actually stopped
at accessing “PMT” == Polymorphic Types (I think).
Then some Googling yielded a suggestion to fix this with “pip3”
This command worked on my raspberry pi, to update pmt
pip3 install pmt
yielding these messages:
Looking in indexes: https://pypi.org/simple, https://www.piwheels.org/simple
Collecting pmt
Downloading https://www.piwheels.org/simple/pmt/pmt-0.0.4-py3-none-any.whl (4.4 kB)
Installing collected packages: pmt
Successfully installed pmt-0.0.4
Good Luck!
Glen
… On Jan 7, 2023, at 11:32 AM, ghassel ***@***.***> wrote:
Hi Glen,
Thanks for the help and instructions. I got a little bit farther, but now
have a new error on cmake that doesn't seem as informative as the previous
one. I'm copying the last parts of what came up, and I can send along any
more info. that might be useful:
-- Found Boost:
/usr/lib/x86_64-linux-gnu/cmake/Boost-1.74.0/BoostConfig.cmake (found
suitable version "1.74.0", minimum required is "1.74.0") found components:
date_time program_options system regex thread unit_test_framework
-- Found Volk: Volk::volk
CMake Error at /usr/local/lib/cmake/gnuradio/GnuradioConfig.cmake:40
(include):
include could not find requested file:
/usr/local/lib/cmake/gnuradio/gnuradio-pmtConfig.cmake
Call Stack (most recent call first):
CMakeLists.txt:88 (find_package)
CMake Error at /usr/local/lib/cmake/gnuradio/GnuradioConfig.cmake:41
(include):
include could not find requested file:
/usr/local/lib/cmake/gnuradio/gnuradio-runtimeConfig.cmake
Call Stack (most recent call first):
CMakeLists.txt:88 (find_package)
-- Found Git: /usr/bin/git
-- Extracting version information from git describe...
fatal: No annotated tags can describe
'1cdb8703a1905547f3d7a9e404e068c7c8d29fa0'.
However, there were unannotated tags: try --tags.
-- Found Doxygen: /usr/bin/doxygen (found version "1.9.1") found
components: doxygen missing components: dot
-- Using install prefix: /usr/local
-- Building for version: g1cdb870 / 1.0.0git
-- No C++ unit tests... skipping
-- PYTHON_EXECUTABLE not set - using default python3
-- Found PythonInterp: /usr/bin/python3.10 (found version "3.10.7")
-- Found PythonLibs: /usr/lib/x86_64-linux-gnu/libpython3.10.so (found
suitable exact version "3.10.7")
-- PYTHON and GRC components are disabled
-- Configuring incomplete, errors occurred!
See also
"/home/viper/Research/temp/gr-radio_astro/build/CMakeFiles/CMakeOutput.log"
I appreciate any suggestions or insights. Thanks!!
On Sat, Jan 7, 2023 at 10:48 AM Glen Langston ***@***.***>
wrote:
> Hi George,
>
> Glad to hear you’re interested in Radio Astronomy and are ready to start
> observations.
>
> It appears that one critical step is necessary if you’ve installed
> GNUradio 3.10 or later. It took me a few tries to get the sequence correct,
> as it has been a while since I reinstalled from scratch.
>
> The first number it the command history number, ignore that:
> 1079 mkdir temp
> 1080 cd temp
> 1081 git clone https://www.github.com/WVURAIL/gr-radio_astro
> 1082 cd gr-radio_astro/
> ...
> 1095 git branch -r -l
> ...
> 1101 git checkout gr310
> 1102 mkdir build
> ...
> 1104 cd build
> 1105 cmake ../
> 1106 make -j 3
>
> This just worked fine. Probably the key piece that is missing is the:
>
> git checkout gr310
>
> step, which removes all mention of code needing SWIG. There are a few more
> steps
> after this including:
> sudo make install
> and
> sudo ldconfig
>
> Let us know how this works out for you!
>
> Best regards
>
> Glen
>
> PS Change the mkdir step to place the code wherever you want it.
> I typically use: ~/Research
>
> ie:
>
> mkdir ~/Research
> cd ~/Research
>
> But this is not required.
>
>
> > On Jan 6, 2023, at 10:19 AM, ghassel ***@***.***> wrote:
> >
> >
> > Hi - I'd like to try out the DSPIRA activities. I ran into a problem
> early in the process, where I'm getting an error on cmake. The error
> messages are:
> > CMake Error at swig/CMakeLists.txt.37 (include):
> > include could not find the requested file:
> > GrSwig
> > and then there was Unknown CMake command "GR_SWIG_MAKE"
> > Is this is a common problem, and is there a known solution?
> > Thanks!
> > -George
> > —
> > Reply to this email directly, view it on GitHub, or unsubscribe.
> > You are receiving this because you were mentioned.Message ID:
> ***@***.***>
>
> —
> Reply to this email directly, view it on GitHub
> <#2 (comment)>,
> or unsubscribe
> <https://github.com/notifications/unsubscribe-auth/AG5YWTF25PYUY6X3S727JW3WRGF4VANCNFSM4TT25DVQ>
> .
> You are receiving this because you commented.Message ID:
> ***@***.***>
>
—
Reply to this email directly, view it on GitHub, or unsubscribe.
You are receiving this because you were mentioned.Message ID: ***@***.***>
|
Hello again George,
After I ran my suggestion (ie pip3 install pmt)
my observing software did not run, so DON’T do the above!
There is some other issue with your environment. Probably re-installing some
package will clear the issues. Sorry to not have a clearer answer.
Good Luck
Maybe if you summarize the software you’ve installed on your computer
we can make a better guess.
Glen
… On Jan 7, 2023, at 11:32 AM, ghassel ***@***.***> wrote:
Hi Glen,
Thanks for the help and instructions. I got a little bit farther, but now
have a new error on cmake that doesn't seem as informative as the previous
one. I'm copying the last parts of what came up, and I can send along any
more info. that might be useful:
-- Found Boost:
/usr/lib/x86_64-linux-gnu/cmake/Boost-1.74.0/BoostConfig.cmake (found
suitable version "1.74.0", minimum required is "1.74.0") found components:
date_time program_options system regex thread unit_test_framework
-- Found Volk: Volk::volk
CMake Error at /usr/local/lib/cmake/gnuradio/GnuradioConfig.cmake:40
(include):
include could not find requested file:
/usr/local/lib/cmake/gnuradio/gnuradio-pmtConfig.cmake
Call Stack (most recent call first):
CMakeLists.txt:88 (find_package)
CMake Error at /usr/local/lib/cmake/gnuradio/GnuradioConfig.cmake:41
(include):
include could not find requested file:
/usr/local/lib/cmake/gnuradio/gnuradio-runtimeConfig.cmake
Call Stack (most recent call first):
CMakeLists.txt:88 (find_package)
-- Found Git: /usr/bin/git
-- Extracting version information from git describe...
fatal: No annotated tags can describe
'1cdb8703a1905547f3d7a9e404e068c7c8d29fa0'.
However, there were unannotated tags: try --tags.
-- Found Doxygen: /usr/bin/doxygen (found version "1.9.1") found
components: doxygen missing components: dot
-- Using install prefix: /usr/local
-- Building for version: g1cdb870 / 1.0.0git
-- No C++ unit tests... skipping
-- PYTHON_EXECUTABLE not set - using default python3
-- Found PythonInterp: /usr/bin/python3.10 (found version "3.10.7")
-- Found PythonLibs: /usr/lib/x86_64-linux-gnu/libpython3.10.so (found
suitable exact version "3.10.7")
-- PYTHON and GRC components are disabled
-- Configuring incomplete, errors occurred!
See also
"/home/viper/Research/temp/gr-radio_astro/build/CMakeFiles/CMakeOutput.log"
I appreciate any suggestions or insights. Thanks!!
On Sat, Jan 7, 2023 at 10:48 AM Glen Langston ***@***.***>
wrote:
> Hi George,
>
> Glad to hear you’re interested in Radio Astronomy and are ready to start
> observations.
>
> It appears that one critical step is necessary if you’ve installed
> GNUradio 3.10 or later. It took me a few tries to get the sequence correct,
> as it has been a while since I reinstalled from scratch.
>
> The first number it the command history number, ignore that:
> 1079 mkdir temp
> 1080 cd temp
> 1081 git clone https://www.github.com/WVURAIL/gr-radio_astro
> 1082 cd gr-radio_astro/
> ...
> 1095 git branch -r -l
> ...
> 1101 git checkout gr310
> 1102 mkdir build
> ...
> 1104 cd build
> 1105 cmake ../
> 1106 make -j 3
>
> This just worked fine. Probably the key piece that is missing is the:
>
> git checkout gr310
>
> step, which removes all mention of code needing SWIG. There are a few more
> steps
> after this including:
> sudo make install
> and
> sudo ldconfig
>
> Let us know how this works out for you!
>
> Best regards
>
> Glen
>
> PS Change the mkdir step to place the code wherever you want it.
> I typically use: ~/Research
>
> ie:
>
> mkdir ~/Research
> cd ~/Research
>
> But this is not required.
>
>
> > On Jan 6, 2023, at 10:19 AM, ghassel ***@***.***> wrote:
> >
> >
> > Hi - I'd like to try out the DSPIRA activities. I ran into a problem
> early in the process, where I'm getting an error on cmake. The error
> messages are:
> > CMake Error at swig/CMakeLists.txt.37 (include):
> > include could not find the requested file:
> > GrSwig
> > and then there was Unknown CMake command "GR_SWIG_MAKE"
> > Is this is a common problem, and is there a known solution?
> > Thanks!
> > -George
> > —
> > Reply to this email directly, view it on GitHub, or unsubscribe.
> > You are receiving this because you were mentioned.Message ID:
> ***@***.***>
>
> —
> Reply to this email directly, view it on GitHub
> <#2 (comment)>,
> or unsubscribe
> <https://github.com/notifications/unsubscribe-auth/AG5YWTF25PYUY6X3S727JW3WRGF4VANCNFSM4TT25DVQ>
> .
> You are receiving this because you commented.Message ID:
> ***@***.***>
>
—
Reply to this email directly, view it on GitHub, or unsubscribe.
You are receiving this because you were mentioned.Message ID: ***@***.***>
|
Hi Glen,
Sorry that your observing software stopped running! Hopefully you're
able to get that fixed.
I'm using Ubuntu 22.04 on a laptop, but will try to get a raspberry pi and
see if that works any better, or I'll try re-installing some other things.
I don't have much else on here other than gnuradio and python3 , I don't
think. Thanks for looking into it for me. I'll reply if I can get
something working.
On Sat, Jan 7, 2023 at 12:54 PM Glen Langston ***@***.***>
wrote:
… Hello again George,
After I ran my suggestion (ie pip3 install pmt)
my observing software did not run, so DON’T do the above!
There is some other issue with your environment. Probably re-installing
some
package will clear the issues. Sorry to not have a clearer answer.
Good Luck
Maybe if you summarize the software you’ve installed on your computer
we can make a better guess.
Glen
> On Jan 7, 2023, at 11:32 AM, ghassel ***@***.***> wrote:
>
>
> Hi Glen,
>
> Thanks for the help and instructions. I got a little bit farther, but now
> have a new error on cmake that doesn't seem as informative as the
previous
> one. I'm copying the last parts of what came up, and I can send along any
> more info. that might be useful:
>
>
> -- Found Boost:
> /usr/lib/x86_64-linux-gnu/cmake/Boost-1.74.0/BoostConfig.cmake (found
> suitable version "1.74.0", minimum required is "1.74.0") found
components:
> date_time program_options system regex thread unit_test_framework
> -- Found Volk: Volk::volk
> CMake Error at /usr/local/lib/cmake/gnuradio/GnuradioConfig.cmake:40
> (include):
> include could not find requested file:
>
> /usr/local/lib/cmake/gnuradio/gnuradio-pmtConfig.cmake
> Call Stack (most recent call first):
> CMakeLists.txt:88 (find_package)
>
>
> CMake Error at /usr/local/lib/cmake/gnuradio/GnuradioConfig.cmake:41
> (include):
> include could not find requested file:
>
> /usr/local/lib/cmake/gnuradio/gnuradio-runtimeConfig.cmake
> Call Stack (most recent call first):
> CMakeLists.txt:88 (find_package)
>
>
> -- Found Git: /usr/bin/git
> -- Extracting version information from git describe...
> fatal: No annotated tags can describe
> '1cdb8703a1905547f3d7a9e404e068c7c8d29fa0'.
> However, there were unannotated tags: try --tags.
> -- Found Doxygen: /usr/bin/doxygen (found version "1.9.1") found
> components: doxygen missing components: dot
> -- Using install prefix: /usr/local
> -- Building for version: g1cdb870 / 1.0.0git
> -- No C++ unit tests... skipping
> -- PYTHON_EXECUTABLE not set - using default python3
> -- Found PythonInterp: /usr/bin/python3.10 (found version "3.10.7")
> -- Found PythonLibs: /usr/lib/x86_64-linux-gnu/libpython3.10.so (found
> suitable exact version "3.10.7")
> -- PYTHON and GRC components are disabled
> -- Configuring incomplete, errors occurred!
> See also
>
"/home/viper/Research/temp/gr-radio_astro/build/CMakeFiles/CMakeOutput.log"
>
> I appreciate any suggestions or insights. Thanks!!
>
>
>
>
>
> On Sat, Jan 7, 2023 at 10:48 AM Glen Langston ***@***.***>
> wrote:
>
> > Hi George,
> >
> > Glad to hear you’re interested in Radio Astronomy and are ready to
start
> > observations.
> >
> > It appears that one critical step is necessary if you’ve installed
> > GNUradio 3.10 or later. It took me a few tries to get the sequence
correct,
> > as it has been a while since I reinstalled from scratch.
> >
> > The first number it the command history number, ignore that:
> > 1079 mkdir temp
> > 1080 cd temp
> > 1081 git clone https://www.github.com/WVURAIL/gr-radio_astro
> > 1082 cd gr-radio_astro/
> > ...
> > 1095 git branch -r -l
> > ...
> > 1101 git checkout gr310
> > 1102 mkdir build
> > ...
> > 1104 cd build
> > 1105 cmake ../
> > 1106 make -j 3
> >
> > This just worked fine. Probably the key piece that is missing is the:
> >
> > git checkout gr310
> >
> > step, which removes all mention of code needing SWIG. There are a few
more
> > steps
> > after this including:
> > sudo make install
> > and
> > sudo ldconfig
> >
> > Let us know how this works out for you!
> >
> > Best regards
> >
> > Glen
> >
> > PS Change the mkdir step to place the code wherever you want it.
> > I typically use: ~/Research
> >
> > ie:
> >
> > mkdir ~/Research
> > cd ~/Research
> >
> > But this is not required.
> >
> >
> > > On Jan 6, 2023, at 10:19 AM, ghassel ***@***.***> wrote:
> > >
> > >
> > > Hi - I'd like to try out the DSPIRA activities. I ran into a problem
> > early in the process, where I'm getting an error on cmake. The error
> > messages are:
> > > CMake Error at swig/CMakeLists.txt.37 (include):
> > > include could not find the requested file:
> > > GrSwig
> > > and then there was Unknown CMake command "GR_SWIG_MAKE"
> > > Is this is a common problem, and is there a known solution?
> > > Thanks!
> > > -George
> > > —
> > > Reply to this email directly, view it on GitHub, or unsubscribe.
> > > You are receiving this because you were mentioned.Message ID:
> > ***@***.***>
> >
> > —
> > Reply to this email directly, view it on GitHub
> > <
#2 (comment)
>,
> > or unsubscribe
> > <
https://github.com/notifications/unsubscribe-auth/AG5YWTF25PYUY6X3S727JW3WRGF4VANCNFSM4TT25DVQ
>
> > .
> > You are receiving this because you commented.Message ID:
> > ***@***.***>
> >
> —
> Reply to this email directly, view it on GitHub, or unsubscribe.
> You are receiving this because you were mentioned.Message ID:
***@***.***>
—
Reply to this email directly, view it on GitHub
<#2 (comment)>,
or unsubscribe
<https://github.com/notifications/unsubscribe-auth/AG5YWTBVQIQK2VJOWJDHNXLWRGUVFANCNFSM4TT25DVQ>
.
You are receiving this because you commented.Message ID:
***@***.***>
|
Hi George,
I do recommend the Pi 400, as they are easy to work with.
I’m in a meeting in Seattle WA, and my telescope computers are in WV.
With VNC, which is in the download image, you automatically can
log into your PIs from anywhere.
See: https://docs.google.com/document/d/1T_IJhRzMmsDWOqOOUYMyr36vEMxKXEbWL_G2tNK9Os8/edit?usp=share_link
This document contains a link to the downloadable operating system
Glen
PS: The pip3 commands are easy to undo. I just typed:
pip3 uninstall pmt
and all was fine again.
… On Jan 7, 2023, at 1:00 PM, ghassel ***@***.***> wrote:
Hi Glen,
Sorry that your observing software stopped running! Hopefully you're
able to get that fixed.
I'm using Ubuntu 22.04 on a laptop, but will try to get a raspberry pi and
see if that works any better, or I'll try re-installing some other things.
I don't have much else on here other than gnuradio and python3 , I don't
think. Thanks for looking into it for me. I'll reply if I can get
something working.
On Sat, Jan 7, 2023 at 12:54 PM Glen Langston ***@***.***>
wrote:
> Hello again George,
>
> After I ran my suggestion (ie pip3 install pmt)
> my observing software did not run, so DON’T do the above!
>
> There is some other issue with your environment. Probably re-installing
> some
> package will clear the issues. Sorry to not have a clearer answer.
>
> Good Luck
>
> Maybe if you summarize the software you’ve installed on your computer
> we can make a better guess.
>
> Glen
>
>
> > On Jan 7, 2023, at 11:32 AM, ghassel ***@***.***> wrote:
> >
> >
> > Hi Glen,
> >
> > Thanks for the help and instructions. I got a little bit farther, but now
> > have a new error on cmake that doesn't seem as informative as the
> previous
> > one. I'm copying the last parts of what came up, and I can send along any
> > more info. that might be useful:
> >
> >
> > -- Found Boost:
> > /usr/lib/x86_64-linux-gnu/cmake/Boost-1.74.0/BoostConfig.cmake (found
> > suitable version "1.74.0", minimum required is "1.74.0") found
> components:
> > date_time program_options system regex thread unit_test_framework
> > -- Found Volk: Volk::volk
> > CMake Error at /usr/local/lib/cmake/gnuradio/GnuradioConfig.cmake:40
> > (include):
> > include could not find requested file:
> >
> > /usr/local/lib/cmake/gnuradio/gnuradio-pmtConfig.cmake
> > Call Stack (most recent call first):
> > CMakeLists.txt:88 (find_package)
> >
> >
> > CMake Error at /usr/local/lib/cmake/gnuradio/GnuradioConfig.cmake:41
> > (include):
> > include could not find requested file:
> >
> > /usr/local/lib/cmake/gnuradio/gnuradio-runtimeConfig.cmake
> > Call Stack (most recent call first):
> > CMakeLists.txt:88 (find_package)
> >
> >
> > -- Found Git: /usr/bin/git
> > -- Extracting version information from git describe...
> > fatal: No annotated tags can describe
> > '1cdb8703a1905547f3d7a9e404e068c7c8d29fa0'.
> > However, there were unannotated tags: try --tags.
> > -- Found Doxygen: /usr/bin/doxygen (found version "1.9.1") found
> > components: doxygen missing components: dot
> > -- Using install prefix: /usr/local
> > -- Building for version: g1cdb870 / 1.0.0git
> > -- No C++ unit tests... skipping
> > -- PYTHON_EXECUTABLE not set - using default python3
> > -- Found PythonInterp: /usr/bin/python3.10 (found version "3.10.7")
> > -- Found PythonLibs: /usr/lib/x86_64-linux-gnu/libpython3.10.so (found
> > suitable exact version "3.10.7")
> > -- PYTHON and GRC components are disabled
> > -- Configuring incomplete, errors occurred!
> > See also
> >
> "/home/viper/Research/temp/gr-radio_astro/build/CMakeFiles/CMakeOutput.log"
> >
> > I appreciate any suggestions or insights. Thanks!!
> >
> >
> >
> >
> >
> > On Sat, Jan 7, 2023 at 10:48 AM Glen Langston ***@***.***>
> > wrote:
> >
> > > Hi George,
> > >
> > > Glad to hear you’re interested in Radio Astronomy and are ready to
> start
> > > observations.
> > >
> > > It appears that one critical step is necessary if you’ve installed
> > > GNUradio 3.10 or later. It took me a few tries to get the sequence
> correct,
> > > as it has been a while since I reinstalled from scratch.
> > >
> > > The first number it the command history number, ignore that:
> > > 1079 mkdir temp
> > > 1080 cd temp
> > > 1081 git clone https://www.github.com/WVURAIL/gr-radio_astro
> > > 1082 cd gr-radio_astro/
> > > ...
> > > 1095 git branch -r -l
> > > ...
> > > 1101 git checkout gr310
> > > 1102 mkdir build
> > > ...
> > > 1104 cd build
> > > 1105 cmake ../
> > > 1106 make -j 3
> > >
> > > This just worked fine. Probably the key piece that is missing is the:
> > >
> > > git checkout gr310
> > >
> > > step, which removes all mention of code needing SWIG. There are a few
> more
> > > steps
> > > after this including:
> > > sudo make install
> > > and
> > > sudo ldconfig
> > >
> > > Let us know how this works out for you!
> > >
> > > Best regards
> > >
> > > Glen
> > >
> > > PS Change the mkdir step to place the code wherever you want it.
> > > I typically use: ~/Research
> > >
> > > ie:
> > >
> > > mkdir ~/Research
> > > cd ~/Research
> > >
> > > But this is not required.
> > >
> > >
> > > > On Jan 6, 2023, at 10:19 AM, ghassel ***@***.***> wrote:
> > > >
> > > >
> > > > Hi - I'd like to try out the DSPIRA activities. I ran into a problem
> > > early in the process, where I'm getting an error on cmake. The error
> > > messages are:
> > > > CMake Error at swig/CMakeLists.txt.37 (include):
> > > > include could not find the requested file:
> > > > GrSwig
> > > > and then there was Unknown CMake command "GR_SWIG_MAKE"
> > > > Is this is a common problem, and is there a known solution?
> > > > Thanks!
> > > > -George
> > > > —
> > > > Reply to this email directly, view it on GitHub, or unsubscribe.
> > > > You are receiving this because you were mentioned.Message ID:
> > > ***@***.***>
> > >
> > > —
> > > Reply to this email directly, view it on GitHub
> > > <
> #2 (comment)
> >,
> > > or unsubscribe
> > > <
> https://github.com/notifications/unsubscribe-auth/AG5YWTF25PYUY6X3S727JW3WRGF4VANCNFSM4TT25DVQ
> >
> > > .
> > > You are receiving this because you commented.Message ID:
> > > ***@***.***>
> > >
> > —
> > Reply to this email directly, view it on GitHub, or unsubscribe.
> > You are receiving this because you were mentioned.Message ID:
> ***@***.***>
>
> —
> Reply to this email directly, view it on GitHub
> <#2 (comment)>,
> or unsubscribe
> <https://github.com/notifications/unsubscribe-auth/AG5YWTBVQIQK2VJOWJDHNXLWRGUVFANCNFSM4TT25DVQ>
> .
> You are receiving this because you commented.Message ID:
> ***@***.***>
>
—
Reply to this email directly, view it on GitHub, or unsubscribe.
You are receiving this because you were mentioned.Message ID: ***@***.***>
|
Hello everyone! My professor is concerned that perhaps our aluminized home insulation board is too thick. Her estimate is the material is about 1 inch thick, give or take. Is this acceptable or should we invest in thinner/thicker insulation? Thanks! |
Hi
The metal surface insulation we’ve used is about 1/2 inch thick. Thicker is OK,
if that’s what you have. The metal coating should be on the inside of the horn.
Good luck,
Glen
… On Nov 13, 2023, at 11:41 AM, EvrettSob ***@***.***> wrote:
Hello everyone!
My professor is concerned that perhaps our aluminized home insulation board is too thick. Her estimate is the material is about 1 inch thick, give or take. Is this acceptable or should we invest in thinner/thicker insulation? Thanks!
—
Reply to this email directly, view it on GitHub, or unsubscribe.
You are receiving this because you were mentioned.Message ID: ***@***.***>
|
Hi,
We use half inch foam board insulation with one side aluminized. It is easy
to work with, inexpensive and lighter.
Best,
Robert Baker
…On Mon, Nov 13, 2023 at 8:41 AM EvrettSob ***@***.***> wrote:
Hello everyone!
My professor is concerned that perhaps our aluminized home insulation
board is too thick. Her estimate is the material is about 1 inch thick,
give or take. Is this acceptable or should we invest in thinner/thicker
insulation? Thanks!
—
Reply to this email directly, view it on GitHub
<#2 (comment)>,
or unsubscribe
<https://github.com/notifications/unsubscribe-auth/ABZERAIV5XUXNSRPZM765WDYEJETXAVCNFSM4TT25DV2U5DIOJSWCZC7NNSXTN2JONZXKZKDN5WW2ZLOOQ5TCOBQHA2TEOBWGMZA>
.
You are receiving this because you commented.Message ID:
***@***.***>
|
Hi, As of today, on page : https://wvurail.org/dspira-lessons/HornOperation_spectrometer_description Thank you for the work put into this. Amazing! Cheers, |
DSPIRA Forum – Digital Signal Processing in Radio Astronomy - Lessons Portal
Lots of lessons
https://wvurail.org//dspira-lessons/forum/
The text was updated successfully, but these errors were encountered: