Replies: 26 comments
-
|
Beta Was this translation helpful? Give feedback.
-
if its a car without a reverse camera and you have put it on as an add on/upgrade I should imagine you will have to enable rear reverse camera in the navigation section with DDT4ALL on your rlink2 |
Beta Was this translation helpful? Give feedback.
-
Yes its is new and activated with ddt4all. it has now the camera menu, but says defet camera or missing signal. so i think i dident use the right pins? i have bought at adapter but it is 32 pin and the radio has 24 pin so i found the connections on the picture but i dont work |
Beta Was this translation helpful? Give feedback.
-
is your camera a 12v or 6v power requirement? |
Beta Was this translation helpful? Give feedback.
-
it is 6 volt. if i connect camera wit power from extern cable there is still no video signal on r link . but there is picture if i connect the video cable to a old tv... |
Beta Was this translation helpful? Give feedback.
-
Beta Was this translation helpful? Give feedback.
-
I think I saw it on this site and it fit fine with the pins that were not in use. so just like you have shown here but - for the camera supply I have taken out the rear lights. But it is not only the power that has problems, because I have tried to supply the camera with external power, so the video signal is also wrong. When the car is put into reverse gear, a black screen appears and it reports a camera error or lack of signal |
Beta Was this translation helpful? Give feedback.
-
yes, it could possibly be different wiring for the rlink2 vs the rlink1 24 pin connector then |
Beta Was this translation helpful? Give feedback.
-
My thought is that mabye there i a different wirring in r-link2 ? |
Beta Was this translation helpful? Give feedback.
-
I found this - pin 21 could it be on the 32pin cable? |
Beta Was this translation helpful? Give feedback.
-
the emty wire holes in my radio is 1,3,4,5,12,14,16,18,19,20,21 . when i have been surfing on the web i have seen a lot of r-link 2 with 32 pin connector, the problem is that mine is a 24 pin and cant find any diagram with 24 pin for r-link 2 so i could be sure of which wires i shoul use |
Beta Was this translation helpful? Give feedback.
-
Thank you Andy, I hope someone have the wire connection for r-link 2 so i for sure can find the faul |
Beta Was this translation helpful? Give feedback.
-
havent found a wiring diagram - but this sounds like the kind of lead you need maybe if yours is a 24pin plug: |
Beta Was this translation helpful? Give feedback.
-
Yes it would be great, but im not sure if the wirring is correct. Its for the elder medinav, i have seen som sellers write , that it wont support r-link? |
Beta Was this translation helpful? Give feedback.
-
You need a diagram for the connection ? I can give you… I need your VIN the lead at the picture is for MediaNav UlC4 not for RLink. It’s different. |
Beta Was this translation helpful? Give feedback.
-
I think that’s important to config the camera at RLink. To „yes“ |
Beta Was this translation helpful? Give feedback.
-
Vin nr. vf1rfa00063460938 thankyou |
Beta Was this translation helpful? Give feedback.
-
vf1rfa00063460938 thank you :-) |
Beta Was this translation helpful? Give feedback.
-
Apropos… you have to visit a garage, there is a OTS to reprogramming your ECUs |
Beta Was this translation helpful? Give feedback.
-
My German is not the Best ;-) is it corrett i should use pin 2,3,5. The car already have a wire in pin 2? |
Beta Was this translation helpful? Give feedback.
-
Im not shure if you have the correct connection. Normally you use the connection from „Radio“ behind the Clovebox. There I can’t find so long the diagram. But I have attached you the manual to install the camera system originally. There are the correct instructions an a diagram to connect. I hope it’s helpful. |
Beta Was this translation helpful? Give feedback.
-
Thank you so much :-) my fault i have trying to connect on the back of r-link screen an not behandling the clovebox. So i learned a lesseon today |
Beta Was this translation helpful? Give feedback.
-
so did you have to join your camera wires to the 32pin connector then? |
Beta Was this translation helpful? Give feedback.
-
Beta Was this translation helpful? Give feedback.
-
Ineed pin location for clio5 |
Beta Was this translation helpful? Give feedback.
-
Hy hope someone can help me. have a scenic iv from 2020 where i want to install reverse camera. anyone can help with a diagram to r-link 2 with 24 pin have tryed 18 cam+ 19 cam - 20 cam + suply but i dont work. thr camera an wire work when i connect to another schreen, so i think it is the wiring there is wrong...
Beta Was this translation helpful? Give feedback.
All reactions